NS3S615Wireless Security Alert System

FEATURES • Including wireless PIR(passive infrared) sensor & receiver • Powerful outdoor weather-PIR sensor detects motion sends a wireless signal to receiver turn on chime • Wireless RF transmission up to 60~90 meters • PIR sensor detection range up to 8 meters, detection angle up to 30 degree • Sound Hi/Off/Low switch of receiver • PIR sensor 9V battery operation (not included) • Receiver 3 "C" size batteries operation (not included) and compatible with AC adaptor (not included) • Battery low indicator LED for PIR sensor & receiver • No wiring, easy to installs OPERATION 1. Remove the screw of PIR sensor unit and Receiver unit from battery cover, and open the battery door.(Fig.1) 2. Install an alkaline 9V batteries (not included) for PIR sensor, 3x1.5 "C-size" batteries for receiver to the battery compartment make sure install with correct polarity. (Fig. 2) 3. Hang the PIR sensor at the entrance of your driveway (such as on a mailbox, on a tree or on a ground stake). You may also place the PIR sensor on your garage, near the front entrance or rear door. Any movement nearby will transmit a signal to the receiver chime unit triggering it to signal the chime.(Fig.3) size:145x205mm p/n:610-615XX-000R 4. Please ensure to place the PIR sensor unit at least three feet high above the ground. 5. High/Off/Low switch of receiver Turn the switch to High position, the unit will standby to Chime mode, when PIR sensor detected trigger, will sound door chime and the led will light up. You can turn HI/LOW switch to select door chime sound volume. 6. To test the PIR sensor unit detection area After selecting a location for installing of the unit you can turn the switch to Chime and wait for 30 seconds for "WARM-UP". Then you try walking in front of the unit. When the unit detects motion, the chime will sound. There will be no chime sound if you walk beyond the detection range. By testing the detection range, you can adjust the location of sensor angle for best coverage. Turn the chime off after your test. 7. Battery low indicator A) PIR sensor When PIR sensor batteries goes low, the LED will lighting to indicate the low battery. Please replace the new battery. B) Receiver When receiver batteries goes low, the LED of the middle will lighting to indicate the low battery. Please replace the new battery. 8. Power adapter (not included) for receiver unit with output 6V DC, 200mA female plug, center ( + ) positive can be applied to the DC jack for long time use. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC ID: NS3S615 - 1 - - 2 - (Fig. 1) Fig.3 (Fig. 2) Wireless Security Alert System Model615

Lelux Electronics Ltd. Unit 6, 10/F, TCL Tower, No.8, Tai Chung Road, Tsuen Wan, New Territories, Hong Kong Confidentiality Letter To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: NS3S615 We hereby request confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, signature : name / title: Luke Lo / President address: Unit 6, 10/F, TCL Tower, No.8, Tai Chung Road, Tsuen Wan, New Territories, Hong Kong

Label location

Antenna location

FCC ID: NS3S615 Keyway Testing Technology Co., Ltd. Report No. 14KWE112030F Page 1 of 22 FCC TEST REPORT for Lelux Electronics Ltd. Wireless Security Alert System Model Number:615 FCC ID: NS3S615 Prepared for : Lelux Electronics Ltd. Address : Unit 6, 10/F, TCL Tower, No.8, Tai Chung Road, Tsuen Wan, New Territories, Hong Kong Prepared by : Keyway Testing Technology Co., Ltd. Address : Baishun Industrial Zone, Zhangmutou Town, Dongguan, Guangdong, China Tel: 86-769-8718 2258 Fax: 86-769-8718 1058 Report No. : 14KWE112030F Date of Test : Nov. 6~10, 2014 Date of Report : Nov. 11, 2014 FCC ID: NS3S615 Keyway Testing Technology Co., Ltd. Report No. 14KWE112030F Page 2 of 22 TABLE OF CONTENTS Test Report Declaration Page 1. GENERAL PRODUCT INFORMATION ............................................................................4 1.1. Product Function.................................................................................................................... 4 1.2. Description of Device (EUT) .................................................................................................. 4 1.3. Independent Operation Modes .............................................................................................. 4 2. TEST SITES .....................................................................................................................5 2.1. Test Facilities ......................................................................................................................... 5 2.2. List of Test and Measurement Instruments............................................................................ 6 3. TEST SET-UP AND OPERATION MODES......................................................................7 3.1. Principle of Configuration Selection ....................................................................................... 7 3.2. Block Diagram of Test Set-up ................................................................................................ 7 3.3. Test Operation Mode and Test Software ............................................................................... 7 3.4. Special Accessories and Auxiliary Equipment ....................................................................... 7 3.5. Countermeasures to Achieve EMC Compliance.................................................................... 7 3.6. Test Environment:.................................................................................................................. 7 4. EMISSION TEST RESULTS.............................................................................................8 4.1. Radiated Emission Test .........................................................................................................8 5. CALCULATION OF AVERAGE FACTOR.......................................................................14 6. 20DB OCCUPY BANDWIDTH ........................................................................................17 6.1. Limits.................................................................................................................................... 17 7. DWELL TIME..................................................................................................................18 7.1. Limits.................................................................................................................................... 18 8. PHOTOGRAPHS OF TEST SET-UP..............................................................................19 9. PHOTOGRAPHS OF THE EUT......................................................................................20 FCC ID: NS3S615 Keyway Testing Technology Co., Ltd. Report No. 14KWE112030F Page 3 of 22 Keyway Testing Technology Co., Ltd. Applicant: Address: Lelux Electronics Ltd.. Unit 6, 10/F, TCL Tower, No.8, Tai Chung Road, Tsuen Wan, New Territories, Hong Kong Manufacturer: Address: Lelux Electronics Ltd.. Unit 6, 10/F, TCL Tower, No.8, Tai Chung Road, Tsuen Wan, New Territories, Hong Kong E.U.T: Wireless Security Alert System Model Number: 615 Trade Name: Serial No.: ------ Date of Receipt: Nov. 6, 2014 Date of Test: Nov. 6~10, 2014 Test Specification: FCC Part 15, Subpart C: Oct. 1, 2014 ANSI C63.4:2009 Test Result: The equipment under test was found to be compliance with the requirements of the standards applied. Issue Date: Nov. 11, 2014 Tested by: Reviewed by: Approved by: Jack Bu / Engineer Andy Gao / Supervisor Jade Yang/ Supervisor Other Aspects: None. Abbreviations: OK/P=passed fail/F=failed n.a/N=not applicable E.U.T=equipment under tested This test report is based on a single evaluation of one sample of above mentioned products. It is not permitted to be duplicated in extracts without written approval of Keyway Testing Technology Co., Ltd. FCC ID: NS3S615 Keyway Testing Technology Co., Ltd. Report No. 14KWE112030F Page 4 of 22 1. GENERAL PRODUCT INFORMATION 1.1. Product Function Refer to Technical Construction Form and User Manual. 1.2. Description of Device (EUT) Description : Wireless Security Alert System M/N : 615 Power Supply : DC 9V Operation Frequency : 433.92MHz Modulation Technology : ASK Antenna Type : Integral Antenna Gain : 2dBi 1.3. Independent Operation Modes The basic operation modes are: 1.3.1. Transmitting mode(TX Mode) 1.3.2. Normal mode. 1.3.3. Transmitting mode(Low voltage Mode) Remark: For all test, used new battery. FCC ID: NS3S615 Keyway Testing Technology Co., Ltd. Report No. 14KWE112030F Page 5 of 22 2. TEST SITES 2.1. Test Facilities Lab Qualifications : 944 Shielded Room built by ETS-Lindgren, USA Date of completion: March 28, 2011 966 Chamber built by ETS-Lindgren, USA Date of completion: March 28, 2011 Certificated by TUV Rheinland, Germany. Registration No.: UA 50207153 Date of registration: July 13, 2011 Certificated by UL, USA Registration No.: 100567-237 Date of registration: September 1, 2011 Certificated by Intertek Registration No.: 2011-RTL-L1-31 Date of registration: October 11…

Text truncated - open the document above for the full version.

Radiated Emission