NTUTX-3013Car Alarm

INSTRUCTION MANUAL TRANSMITTER FCC ID : NTUTX-3013 “This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” “ Caution : Any change or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.” 1 . INTRODUCTION The TX-3013 is a miniature code hopping 4 button and 4 channel transmitter, designed for use in advanced, high-security alarm and remote control systems. Transmission is activated by depressing the recessed 4 push buttons at the front of the unit. When activated, transmitter sends out 32-bit hopping code and 4-bit function code. Operation power is obtained from an internal 12volt alkaline battery. An LED lights during transmission, indicating the battery voltage condition. If the LED does not light during transmission, the battery must be replaced immediately. 2.SPECIFICATIONS FREQUENCY : 315MHZ EN-CODING : 28-BIT SERIAL NUMBER, 32-BIT HOPPING CODE AND 4-BIT FUNCTION CODE POWER SUPPLY : 12VOLT ALKALINE BATTERY ( 27A OR EQUIVALENT ) ATTENTION : TRANSMITTER CHARACTERISTICS MAY BE AFFECTED BY BATTERY CONDITION. - PAGE 1 – 3. FUNCTIONS OF EACH BUTTONS CHANNEL #1 OUTPUT FOR DOOR UNLOCKING CHANNEL #3 OUTPUT FOR DOOR LOCKING CHANNEL #2 OUTPUT FOR OPTIONAL OPERATION CHANNEL #4 OUTPUT FOR OPTIONAL OPERATION - PAGE 2 -

EXTERNAL TOP SIDE EXTERNAL BOTTOM SIDE FCC ID : NTUTX-3013

PROPOSED FCC ID. LABEL AND MARKING BOTTOM SIDE

INTERNAL TOP SIDE INTERNAL BOTTOM SIDE FCC ID : NTUTX-3013 FCC ID : NTUTX-3013

Description of Circuit Function FCC ID : NTUTX-3013 DATE : NOV. 17, 1999 MODEL : TX-3013 The TX-3013 is a remote control unit transmitting RF by loop antenna in the PCB pattern. It is operated by pressing theSW1, SW2, SW3 and SW4. If the SW1-SW4 would be pressed, the IC1 will transmit the code received through JP1 and the code will be output via R2 through the No 6 pin of IC. The R3 and C3 are power filter circuit of IC1 and the LED1 would be turned on when the IC1 is operated. The Q1 would be operated by data code received through R2 and the frequency would be fixed as 315MHZ by SAW resonator RE1. The L1 and loop antenna and C1 would transmit the frequency fitted with 315MHZ.

KTL Korea Testing Laboratory Page 1 of 15 TEST REPORT This test report only responds to the tested sample and shall not be reproduced except in full without written approval of the the Korea Testing Laboratory. Tested and reported by Reviewed by Soun-Kweon Seol , Senior Engineer Seok-Jin Kim , EMC Team Leader KOREA TESTING LABORATORY FG101-01-02-00 222-13, Guro-Dong Guro-Gu Seoul Korea 152-053 http://www.ktl.re.kr Ref. Report No. 99-341-055 Name and address of the applicant Young Jin Electronics Co., Ltd. Young Jin Bldg. 335-151, Sangdo-3Dong, Dongjak-Ku, Seoul, Korea 156-033 Standard / Test regulation FCC Part 15, Subpart C Test result Pass Incoming date : November 22, 1999 Test item(s) ; Security/Remote Control Transmitter (Car Alarm) Model/type ref. ; TX-3013 Manufacturer ; Young Jin Electronics Co., Ltd. Additional information ; -Required Authorization :Certification -FCC ID. : NTUTX-3013 Test date : December 11~14, 1999 Issue date : December 21, 1999 Ref. Report No. 99 - 341 - 055 Page 2 of 15 TABLE OF CONTENTS . GENERAL INFORMATION ................................................................................................................... 3 1. Grantee Name and Mailing Address 2. Manufacturer's Name and Mailing Address 3. Equipment Descriptions 4. Rules and Regulations 5. Measuring Procedure 6. Place of Measurement 7. Date of Measurement . GENERAL REQUIREMENTS OF THE EUT ...................................................................................... 5 1. Labelling Requirement (Section 15.19) 2. Information to User (Sections 15.21) 3. Special Accessories (Section 15.27) 4. Compliant Conditions (Section 15.231) 5. Modification of the Equipment Under Test . INPUT POWER MEASUREMENT (Section 15.31)............................................................................. 6 . RADIATED EMISSION MEASUREMENT (Section 15.231)............................................................ 7-13 1. Test Procedure 2. Photograph for the worst case configuration 3. Sample Calculation 4. Measurement Data 5. Reference Data . OCCUPIED BANDWIDTH MEASUREMENT (Section.15.231)...................................................... 14 . TEST EQUIPMENTS USED FOR FCC COMPLIANCE TESTING................................................ 15 Ref. Report No. 99 - 341 – 055 Page 3 of 15 . GENERAL INFORMATION 1. Grantee Name and : Young Jin Electronics Co.,Ltd. Mailing Address Young Jin Bldg. 335-151, Sangdo-3Dong, Dongjak-Ku, Seoul, Korea 156-033 2. Manufacturer's Name and : Young Jin Electronics Co.,Ltd. Mailing Address Young Jin Bldg. 335-151, Sangdo-3Dong, Dongjak-Ku, Seoul, Korea 156-033 3. Equipment Descriptions 3.1 Operating Frequency : 315.0MHz 3.2 Type of Emission : Pulse Code Signal 3.3 Power Supply : DC 12.0V (Battery) 3.4 Additional Information; - Oscillator used : 315.0MHz SAW generator - I.C. used : HCS301 4. Rules and Regulations : FCC Part 15, Subpart C 5. Measuring Procedure : ANSI C63.4-1992 6. Place of Measurement : Absorber-lined room(3-Meter) of KAITECH 7. Date of Measurement 6.1 Conducted Emission : Not Applicable 6.2 Radiated Emission : December 14, 1999 Ref. Report No. 99 - 341 - 055 Page 4 of 15 . GENERAL REQUIREMENTS OF THE EUT 1. Labelling Requirement (Section 15.19) 1.1 Location on Enclosure : Manual for Installation and Operating Instruction 1.2 How Applied : Printing 2. Information to User (Section 15.21) The following or similar statements were provided in the manual for user instruction. Please refer page 1 of the attached manual for details. 3. Special Accessories (Section 15.27) 3.1 Were the special Accessories provided? [ ] yes, [ x ] no 3.2 If yes, details for the special accessories are as follows : 3.3 If yes, were the appropriate instructions provided on the first page of the text concerned with the device? [ ] yes, [ ] no 3.4 Are these accessories provided of the type which can be readily obtained from multiple retail outlets? [ ] yes, [ ] no And therefore does the manual specify what additional components or accessories are required to used in order to comply with the Rules? [ ] yes, [ ] no This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Ref. Report No. 99 - 341 – 055 Page 5 of 15 4. Compliant Conditions (Section 15.231) 4.1 Was the EUT used for continuous transmissions, such as voice or video, and data transmission ? [ ] yes, [ x ] no 4.2 Was the EUT manually operated ? [ x ] yes, [ ] no If yes, did the EUT employ a switch that would automatically deactivate the transmitter within not more than 5 seconds of being released ? [ x ] yes, [ ] no 4.3 Was the EUT automatically activated ? [ ] yes, [ x ] no If yes, did the EUT cease transmission within 5 seconds after deactivation ? [ ] yes, [ ] no 4.4 Was the EUT used for periodic transmissions at regular predetermined intervals ? [ ] yes, [ x ] no 5. Modification of the Equipment Under Test [ x ] Any modifications were not made to the EUT during the testing since the test results were found of be complied with the FCC Rules with the EUT in the as received condition. [ ] Modification(s) was(were) made to the EUT in order to make it meet FCC Rules since it had shown non- compliance for some test items in the course of our testing. - Status of non-compliance : - Details of Modifications : Ref. Report No. 99 - 341 - 055 Page 6 of 15 . INPUT POWER MEASUREMENT (Section 15.31) INPUT POWER 50.6 mW Note : 1. Input Power : P ove = (P p x D) pulse + P D Where, P p : Input Peak Power (= V x I p ) P D : Input DC Power (= V x I D ) D : Duty Cycle (= τ eff x PRF) Measured Input Voltage (V) = 12.31 DCV …

Text truncated - open the document above for the full version.

TEST SETUP PHOTOS RADIATED EMISSION