NVRCSI-DSP25XHCPBidirectional Amplifier

CSI-DSP85-252-C/P & CSI-DSP85I-255-C/P Installation Manual Table of Contents Document Purpose / Intended Users .......................................................... 4 Product Registration Information ............................................................... 4 Application ............................................................................................. 4 Safety Guidelines .................................................................................... 4 Important Safety Information .................................................................... 5 Terms used in this manual ........................................................................ 5 Product Introduction ................................................................................ 5 Band Plans ............................................................................................. 6 File Naming Conventions .......................................................................... 7 LED Indicator .......................................................................................... 8 Functional Overview ................................................................................. 8 Ethernet ................................................................................................. 9 Monitoring & Alarms ................................................................................ 9 USB Interface ......................................................................................... 9 Local Communication Interface Ports .......................................................... 9 EIA232 Pin Specifi cations .......................................................................... 9 System Set-Up Considerations ................................................................ 10 Mounting the Digital Repeater ................................................................. 12 Optional Accessories .............................................................................. 13 Circuit Operational Description ................................................................ 13 Important Installation Notes ................................................................... 13 Functional Block Diagram ....................................................................... 14 Mechanical Specifi cations ........................................................................ 15 AC Power Specifi cations .......................................................................... 15 Dual Band Operating Power Parameters .................................................... 16 Mechanical Drawing ............................................................................... 17 System Status: ..................................................................................... 18 Web based GUI Session .......................................................................... 18 Local Network: ...................................................................................... 19 RF Confi guration: .................................................................................. 20 Program a Filter: ................................................................................... 21 Remote Network: .................................................................................. 22 SNMP Confi guration: .............................................................................. 22 Install & Upload: ................................................................................... 23 System Health: ..................................................................................... 23 Change Password: ................................................................................. 26 Text Menu Interface (Local Access) .......................................................... 26 Telnet Session (Remote Access) ............................................................... 30 Modem Interface (Remote Access with login) ............................................ 32 Additional Tips ...................................................................................... 32 Index ................................................................................................... 36 -4- Application This guide should be applied whenever a need exists to add Digital Repeater capability to an existing system or when this capability is being included with a new installation. Safety Guidelines The general safety information in this guideline applies to both operating and service personnel. Specifi c warnings and cautions will be found in other parts of this manual where they apply, but may not appear in this summary. Failure to comply with these precautions or specifi c warnings elsewhere in the manual violates safety standards of design, manufacture, and intended use of equipment. Cellular Specialties, Inc. assumes no liability for the customer’s failure to comply with these requirements: Grounding This Digital Repeater system is designed to operate from 100-240 VAC and should al- ways be operated with the ground wire properly connected. Do not remove or otherwise alter the grounding lug on the power cord. Explosive Atmospheres To avoid explosion or fi re, do not operate this product in the presence of fl ammable gases or fumes. Lightning Danger Do not install or make adjustments to this unit during an electrical storm. Use of a suitable lightning arrester, such as CSI’s model number CSI-CAP, is very strongly recom- mended. No User Serviceable Parts Inside HAZARDOUS VOLTAGES ARE PRESENT WHEN THE COVER IS REMOVED. Opening the chassis will void your warranty. If you suspect a malfunction with this product, call your dealer or the Cellular Specialties Support Line at: (603) 626-6677, Toll Free (USA) 1-877-844-4274. The serial number may be found on the label on the bottom panel, near the power connectors . Note this number below. Retain this manual, along with proof of purchase, to serve as a …

Text truncated - open the document above for the full version.

December 1, 2010 Federal Communications Commission Office of Engineering and Technology 7435 Oakland Mills Rd. Columbia, MD 21046 Subject: Request for Confidentiality Dear Sir or Madam: Cellular Specialties, Inc. respectfully requests that the schematic diagrams, block diagram, and circuit descriptions submitted with the application for certification under FCC ID: NVRCSI-DSP25XHCP be withheld from public disclosure. This request is made under the provisions of Section 0.457 (d) of the Commission’s rules and Section 0.552 (b) (4) of the Freedom of Information Act. This product has been developed at considerable expense, and disclosure of this information would place Cellular Specialties, Inc. at a competitive disadvantage. Thank you for your attention to this matter. Sincerely yours, Burt Salkins Burt Salkins Director of Engineering

December 1, 2010 Retlif Testing Laboratories 101 New Boston Road Goffstown, NH 03045 Attn: Scott Wentworth Ref: AGENT AUTHORIZATION/ANTI-DRUG ABUSE CERTIFICATION Dear Scott, Cellular Specialties, Inc. hereby authorizes Retlif Testing Laboratories, 101 New Boston Road, Goffstown, NH 03045 to act as our agent in all matters pertaining to FCC and Industry Canada Certification of our CSI-DSP85-25XH-CP Bidirectional Amplifier. Cellular Specialties, Inc. (The Applicant) Certifies that neither Cellular Specialties, Inc. nor any party to the application is subject to denial of Federal benefits, that include FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. Sincerely, Burt Salkins Director of Engineering

MODEL CSI-DSP85-25XH-CP Repeater FCC ID and IC LABEL FCC ID: NVRCSI-DSP25XHCP This device complies with parts 22, 24 and 2 of the FCC rules and Industry Canada IC: 4307A-DSP25XHCP Model No: CSI-DSP85-25XH-CP

1 December 2010 Federal Communications Commission Authorization and Evaluation Division Re: Adjustment of the Model CSI-DSP85-25XH-CP In-building Amplifier in the Field The CSI Model DSP85-25XH-CP In-Building Amplifier offers only adjustment of gain (below its factory-set maximum gain level) to the technician during installation and maintenance activities. This adjustment is dependent on the physical environment in which the amplifier is to be installed and is described in the Installation and Users Manual. This is the only adjustment accessible without opening the amplifier. Frequency response and gain thresholds are factory set and in no circumstance are they to be adjusted in the field. Regards, Burt Salkins Burt Salkins Director of Engineering

Evaluation of the CSI Model DSP85-25XH-CP BDA For Compliance with FCC Guidelines For Human Exposure to Radio Frequency Electromagnetic Fields 1 December 2010 General The CSI Model DSP85-25XH-CP Repeater is considered to be a dual-band “mobile” device operating in both the Cellular Service authorized under subpart H of part 22 and in the Personal Communication Service authorized under part 24. As such, the equipment is required to be evaluated for RF exposure if operated below 1.5 GHz with an effective radiated power (ERP) of 1.5 watts or more or if operated above 1.5 GHz with an effective radiated power (ERP) of 3.0 watts or more, as defined in 2.1091 of FCC rules. Downlink For the downlink portion of the Model DSP85-25XH-CP Repeater, the maximum rated output power is +33.0 dBm (2000 mW) in the Cellular Band (<1.5 GHz) and 30.0 dBm (2000 mW) in the PCS band (>1.5 GHz). As stated in the Model DSP85-25XH-CP Manual, the maximum authorized indoor antenna gain is 3 dBi, corresponding to a typical Multi-Band Omni-Directional antenna. The Table below shows the results of the calculated ERP for both cases, neglecting cable losses. Frequency Power Out Ant Gain EIRP ERP Limit 869-894 MHz 37.0 dBm 3 dBi 40.0 dBm 6068 mW 1.5 W 1930-1990 MHz 37.0 dBm 3 dBi 40.0 dBm 6068 mW 3.0 W As shown above, both frequency bands exceed the allowable limit and must be evaluated for minimum separation distances in order to comply with the exposure limits of 1.1310 of the FCC rules Using the guidelines in FCC OET Bulletin 65 and Supplement C, the power density at a reasonable distance from the maximum gain antenna was calculated. The minimum safe distance was also determined based on the uncontrolled exposure limits defined in Table 1B of FCC rules 1.1311. The following assumptions are made concerning these calculations: CELL Band PCS Band Po = 5000 mw average 5000 mw Cable Loss = 0 dB 0 dB Ant Gain = 3 dBi 3 dBi Frequency = 881.5 MHz 1960 MHz Main Beam (worst-case) Main Beam 100% reflection 100% reflection Reasonable Distance = 4 feet (122 cm) 4 feet (122 cm) Therefore, from OET Bulletin 65, S = (PG)/4πR 2 or S = EIRP/4πR 2 For 100% reflection, a doubling of the field strength can be expected. The above equation can be modified to, S = (2) 2 PG/4πR 2 = EIRP/πR 2 Solving for S at a distance of 4 feet (122 cm) gives, S = (5000) (2)/ π (122) 2 = 0.21 mw/cm 2 From FCC rules 1.1311, Table 1B, the allowable limit for uncontrolled exposure is f(MHz) / 1500. At 881.5 MHz this corresponds to a level of 0.59 mw/cm 2 . For frequencies above 1500 MHz the limit is 1.0 mw/cm 2 . The calculated value of 0.21 is below both these limits thereby showing compliance under worst-case operating conditions. The Cautions in the Model DSP85-25XH-CP manual clearly define the antenna selection and installation criteria in order to maintain a minimum 122-centimeter separation. Uplink For the downlink portion of the Model DSP85-25XH-CP, the maximum rated output power is +31.0dbm (1258 mW) in the Cellular Band (<1.5 GHz) and 27.0 dBm (500 mW) in the PCS band (>1.5 GHz). As stated in the Model DSP85-25XH-CP Manual, the maximum authorized outdoor antenna gain is 14 dBi, corresponding to a typical Multi- Element Yagi-Directional antenna. The Table below shows the results of the calculated ERP for both cases, neglecting cable losses. Frequency Power Out Ant Gain EIRP ERP Limit 824-849 MHz 31.0 dBm 14 dBi 45.0 dBm 19,188 mW 1.5 W 1850-1910 MHz 27.0 dBm 14 dBi 41.0 dBm 7,639 mW 3.0 W As shown in the above table, the Cellular and PCS band exceeds the allowable limit and must be evaluated for minimum separation distances in order to comply with the exposure limits of 1.1310 of the FCC rules. Using the guidelines in FCC OET Bulletin 65 and Supplement C, the power density at a reasonable distance from the maximum gain antenna was calculated. The minimum safe distance was also determined based on the uncontrolled exposure limits defined in Table 1B of FCC rules 1.1311. The following assumptions are made concerning these calculations: Cellular Band PCS Band Po = 1258 mw average 500 mw Cable Loss = 0 dB 0 dB Ant Gain = 14 dBi 14 dBi Frequency = 836.5 MHz 1920 MHz Main Beam (worst-case) Main Beam Rooftop 100% reflection Rooftop Reasonable Distance = 6 feet (183 cm) 6 feet Therefore, from OET Bulletin 65, S = (PG)/4πR 2 or S = EIRP/4πR 2 For 100% reflection, a doubling of the field strength can be expected. The above equation can be modified to, S = (2) 2 PG/4πR 2 = EIRP/πR 2 Solving for S at a distance of 6 feet (183 cm) gives, Cellular PCS S = (1258) (25)/ π (183) 2 = 0.30 mw/cm 2 S = (500) (25)/ π (183) 2 = 0.12 mw/cm 2 From FCC rules 1.1311, Table 1B, the allowable limit for uncontrolled exposure is f(MHz) / 1500. At 836.5 MHz this corresponds to a level of 0.56 mw/cm 2 . For frequencies above 1500 MHz the limit is 1.0 mw/cm 2 . The calculated values of 0.30 and 0.12 are below both these limits thereby showing compliance under worst-case operating conditions. As in the case of the downlink, the Cautions in the Model DSP85-25XH-CP manual clearly define the antenna selection and installation criteria in order to maintain a conservative 6-foot separation.

Test Report No. R-5398N-2 Retlif Testing Laboratories R CERTIFICATION AND SIGNATURES We certify that this report is a true report of the results obtained from the tests of the equipment stated and relates only to the equipment tested. We further certify that the measurements shown in this report were made in accordance with the procedures indicated and vouch for the qualifications of all Retlif Testing Laboratories personnel taking them. Scott Wentworth Branch Manager NVLAP Approved Signatory Todd Hannemann Laboratory Supervisor iNARTE Certified ATL-0255-T Non-Warranty Provision The testing services have been performed, findings obtained, and reports prepared in accordance with generally accepted testing laboratory principles and practices. This warranty is in lieu of all other warranties, either express or implied. Non-Endorsement This test report contains only findings and results arrived at after employing the specific test procedures and standards listed herein. It is not intended to constitute a recommendation, endorsement, or certification of the product or material tested. This report must not be used by the client to claim product endorsement by NVLAP, NIST or any agency of the U.S. Government. Page 2 of 159 Test Report No. R-5398N-2 Retlif Testing Laboratories R CERTIFICATION APPLICATION SUMMARY Applicant/Manufacturer: Cellular Specialties 670 North Commercial Street Manchester, NH 03101 Equipment under Test (EUT): The EUT is a dual band Digital Repeater System operating in the Cellular and PCS bands. Model: CSI-DSP85-25XH-CP FCC ID Number: FCC ID: NVRCSI-DSP25XHCP IC Certification Number: 4307A-DSP25XHCP Applicable Test Standards: FCC Parts 2, 22 & 24, RSS-131, Issue 2 Measurement Procedure: ANSI/TIA-603-C-2004 RSS-131, Issue 2 Device Classification: Mobile EUT Frequency Range Bands: Cell Band Uplink: 824 MHz to 849 MHz Cell Band Downlink: 869 MHz to 894 MHz PCS Band Uplink: 1850 MHz to 1910 MHz PCS Band Downlink: 1930 MHZ to 1990 MHz Power Output Rating for FCC Certification Grant based on 824MHz to 849MHz (IS-95 CDMA): = 1.05W on Intermodulation Data Composite 824MHz to 849MHz (W-CDMA): = 1.30W Power: 824MHz to 849MHz (TDMA): = 1.39W 869MHz to 894MHz (IS-95 CDMA) = 3.13W 869MHz to 894MHz (W-CDMA) = 4.16W 869MHz to 894MHz (TDMA) = 4.42W 1850MHz to 1910MHz (IS-95 CDMA) = .300W 1850MHz to 1910MHz (W-CDMA) = .363W 1850MHz to 1910MHz (TDMA) = .530W 1930MHz to 1990MHz (IS-95 CDMA) = 2.65W 1930MHz to 1990MHz (W-CDMA) = 3.24W 1930MHz to 1990MHz (TDMA) = 4.07W Modulation Types: TDMA (DXW), CDMA-IS95 (F9W), WCDMA (F9W) RF Exposure + Antenna Installation: See Attached Installation/Users Manual and MPE Evaluation Page 3 of 159 Test Report No. R-5398N-2 Retlif Testing Laboratories R Measurements Required by FCC: See Report Section 1 (Summary of Test Program) - RF Power Output - Occupied Bandwidth - Intermodulation Characteristics - Frequency Stability - Spurious Emissions at Antenna Terminals - Effective Radiated Power of Spurious Radiation Additional Measurements Required by RSS -131: - Mean Output Power - Passband Gain & Bandwidth - Spurious Emissions (two tone) - 99% Bandwidth Page 4 of 159 Test Report No. R-5398N-2 Retlif Testing Laboratories R SECTION 1 SUMMARY OF TEST PROGRAM OCCUPIED BANDWIDTH Measurement Procedure: For Occupied Bandwidth, measurements were made to compare the input signal to the output signal. The signal generator output was connected to the spectrum analyzer. A TDMA modulation signal was then applied to the carrier. Waveforms were then noted on an X-Y plot. Next, the signal generator was connected to the EUT and the output of the EUT was connected to the spectrum analyzer. The output waveform after amplification was then compared to the original input signal to ensure that no significant differences occurred between the input signal and the amplified signal. Testing was performed at three frequencies within each passband (uplink and downlink). Testing was repeated for CDMA (IS95) & W-CDMA modulation types. See Occupied Bandwidth Data. SPURIOUS EMISSIONS AT ANTENNA TERMINALS Measurement Procedure: The signal generator output was connected in turn to the uplink and downlink input ports of the EUT. The input power level was at the maximum level which was ascertained during the Power Output test. A spectrum analyzer was connected to the output of the EUT. The input test frequencies used were three frequencies (low, mid & high) within each passband (uplink and downlink). The level of any spurious emission was recorded. Testing was performed in the frequency range of 30MHz to 20GHz. Testing was performed for TDMA, CDMA (IS95) and WCDMA modulation types. The spurious emissions limit is -13dBm as specified in FCC Parts 22 & 24. All emissions were below the specified -13dBm limit. See attached test data. EFFECTIVE RADIATED POWER OF SPURIOUS RADIATION Measurement Procedure: The test sample was placed on an 80cm high wooden test stand which was located 3 meters from the test antenna on an FCC listed test site. A signal generator was connected to the input of the amplifier. The signal generator output was set to provide the input power level necessary to achieve maximum output power of the amplifier at 3 frequencies (low, mid & high) within each passband (uplink and downlink). The effective radiated power of each out of band spurious emission was measured using the substitution method specified in ANSI/TIA-603-C-2004. The frequency range of the test was 30MHz – 20GHz. The limit for out of band spurious emissions is -13dBm as specified in Parts 22 & 24. All emissions were below the specified -13dBm limit. See attached test data. Page 5 of 159 Test Report No. R-5398N-2 Retlif Testing Laboratories R RF POWER OUTPUT (Composite Power) Measurement Procedure: The RF Power Output test was performed in conjunction with the intermodulation test using RMS channel power measurements of two channels with a one channel separation in between. The measurements were taken with the AGC turned…

Text truncated - open the document above for the full version.