NVRCSIDSP95255PS8DSP95 PS8 BIDIRECTIONAL AMPLIFIER

CSI-DSP95-252-PS8, CSI-DSP95I-252-PS8, CSI-DSP95-255-PS8, CSI-DSP95I-255-PS8, CSI-DSP95-260-PS8, and CSI-DSP95I-260-PS8 -2- This page intentionally left blank. Table of Contents Product Registration Information ................................................................................................................... 4 Document Purpose / Intended Users.............................................................................................................. 4 Application ........................................................................................................................................................ 4 Radio and Television Interference .................................................................................................................. 4 Safety Guidelines ............................................................................................................................................. 4 Important Safety Information .......................................................................................................................... 5 Terms used in this manual .............................................................................................................................. 5 Product Introduction ........................................................................................................................................ 5 Band Plan and Filter Naming Convention ...................................................................................................... 6 Functional Overview ........................................................................................................................................ 7 LED Indicator .................................................................................................................................................... 7 Local Communication Interface Ports ............................................................................................................ 8 EIA232 Pin Specifi cations................................................................................................................................ 8 USB Interface .................................................................................................................................................... 8 Ethernet ............................................................................................................................................................. 8 Monitoring & Alarms ........................................................................................................................................ 9 System Set-Up Considerations ....................................................................................................................... 9 Selection of external attenuators to be used in line with the Antenna Port(s) ........................................... 9 1:1 Port Confi guration ..................................................................................................................................... 9 Donor Port ....................................................................................................................................................... 10 Server Port ...................................................................................................................................................... 10 Attenuator Selection Guidelines ................................................................................................................... 10 Mounting the Digital Repeater ........................................................................................................................11 Wall Mounting .................................................................................................................................................11 19” Relay Rack Mounting ..............................................................................................................................11 19” Four Post Rack Mounting .......................................................................................................................11 Important Installation Notes .......................................................................................................................... 12 Installation Tips .............................................................................................................................................. 12 Donor Antenna ................................................................................................................................................ 12 Indoor Antennas ............................................................................................................................................. 12 Optional Accessories ..................................................................................................................................... 12 Circuit Operational Description .................................................................................................................... 13 Functional Block Diagram ............................................................................................................................. 13 Mechanical Specifi cations ............................................................................................................................. 14 Environmental Requirements........................................................................................................................ 14 AC Power Specifi cations ............................................................................................................................... 14 Operating Power Parameters ........................................................................................................................ 15 Mechanical Drawing .....................................…

Text truncated - open the document above for the full version.

MODEL CSI-DSP95-255-PS8 Repeater FCC ID LABEL FCC ID: NVRCSIDSP95255PS8 This device complies with parts 90 and 2 of the FCC rules

Cellular Specialties, FCC ID: NVRCSIDSP95255PS8 Internal Photos Cellular Specialties, FCC ID: NVRCSIDSP95255PS8 Internal Photos Cellular Specialties, FCC ID: NVRCSIDSP95255PS8 Internal Photos Cellular Specialties, FCC ID: NVRCSIDSP95255PS8 Internal Photos Cellular Specialties, FCC ID: NVRCSIDSP95255PS8 Internal Photos Cellular Specialties, FCC ID: NVRCSIDSP95255PS8 Internal Photos Cellular Specialties, FCC ID: NVRCSIDSP95255PS8 Internal Photos Cellular Specialties, FCC ID: NVRCSIDSP95255PS8 Internal Photos

Evaluation of the CSI Model CSI-DSP95-255-PS8 BDA For Compliance with FCC Guidelines For Human Exposure to Radio Frequency Electromagnetic Fields 06 June 2011 General The CSI Model CSI-DSP95-255-PS8 Bi-directional amplifier is considered to be a dual- band “mobile” device operating in both the Cellular Service authorized under part 90. As such, the equipment is required to be evaluated for RF exposure if operated below 1.5 GHz with an effective radiated power (ERP) of 1.5 watts or more or if operated above 1.5 GHz with an effective radiated power (ERP) of 3.0 watts or more, as defined in 2.1091 of FCC rules. Downlink For the downlink portion of the Model CSI-DSP95-255-PS8 BDA, the maximum rated output power is +38.5dBm (7980 mW) in the 800 MHz band ( <1.5 GHz). As stated in the Model CSI-DSP95-255- PS8 Manual, the maximum authorized indoor antenna gain is 3 dBi, corresponding to a typical Multi-Band Omni-Directional antenna. The Table below shows the results of the calculated ERP, neglecting cable losses. Frequency Power Out Ant Gain EIRP ERP Limit 851-869 MHz 38.5dBm 3 dBi 41.5dBm 8610 mW 1.5 W As shown in the above table, the level exceeds the allowable limit and must be evaluated for minimum separation distances in order to comply with the exposure limits of 1.1310 of the FCC rules. Using the guidelines in FCC OET Bulletin 65 and Supplement C, the power density at a reasonable distance from the maximum gain antenna was calculated. The minimum safe distance was also determined based on the uncontrolled exposure limits defined in Table 1B of FCC rules 1.1311. The following assumptions are made concerning these calculations: 800 MHz Band Po = 7980 mw average Cable Loss = 0 dB Ant Gain = 3 dBi Frequency = 860 MHz Main Beam (worst-case) 100% reflection Reasonable Distance = 4 feet ( 122 cm) Therefore, from OET Bulletin 65, S = (PG)/4πR 2 or S = EIRP/4πR 2 For 100% reflection, a doubling of the field strength can be expected. The above equation can be modified to, S = (2) 2 PG/4πR 2 = EIRP/πR 2 Solving for S at a distance of 4 feet ( 122 cm) gives, S = (7980) (2)/ π ( 122) 2 = 0.34 mw/cm 2 From FCC rules 1.1311, Table 1B, the allowable limit for uncontrolled exposure is f(MHz) / 1500. At a frequency of 860 MHz, the limit is 0.57 mw/cm 2 . The calculated value of 0.34 is below the limit thereby showing compliance under worst- case operating conditions. The Cautions in the Model CSI-DSP95-255- PS8 manual clearly define the antenna selection and installation criteria in order to maintain a minimum 4 feet ( 122 cm) separation. Uplink For the uplink portion of the Model CSI-DSP95-255- PS8 BDA, the maximum rated output power is +32.22dBm (1667 mW) in the 800 MHz Band (<1.5 GHz). As stated in the Model CSI-DSP95-255- PS8 Manual, the maximum authorized outdoor antenna gain is 14 dBi, corresponding to a typical Multi-Element Yagi-Directional antenna. The Table below shows the results of the calculated ERP for this case, neglecting cable losses. Frequency Power Out Ant Gain EIRP ERP Limit 806-824 MHz 32.22 dBm 14 dBi 46.22 dBm 25527 mW 1.5 W As shown in the above table, the level exceeds the allowable limit and must be evaluated for minimum separation distances in order to comply with the exposure limits of 1.1310 of the FCC rules. Using the guidelines in FCC OET Bulletin 65 and Supplement C, the power density at a reasonable distance from the maximum gain antenna was calculated. The minimum safe distance was also determined based on the uncontrolled exposure limits defined in Table 1B of FCC rules 1.1311. The following assumptions are made concerning these calculations: 800 MHz Band Po = 1667 mw average Cable Loss = 0 dB Ant Gain = 14 dBi Frequency = 815 MHz Main Beam (worst-case) Rooftop 100% reflection Reasonable Distance = 6 feet (183 cm) Therefore, from OET Bulletin 65, S = (PG)/4πR 2 or S = EIRP/4πR 2 For 100% reflection, a doubling of the field strength can be expected. The above equation can be modified to, S = (2) 2 PG/4πR 2 = EIRP/πR 2 Solving for S at a distance of 6 feet (183 cm) gives, S = (1667) (25)/ π (183) 2 = .4 mw/cm 2 From FCC rules 1.1311, Table 1B, the allowable limit for uncontrolled exposure is f(MHz) / 1500. At a frequency of 815 MHz, the limit is 0.54mw/cm 2 . The calculated value of 0.4 is below both the limit thereby showing compliance under worst-case operating conditions. The Cautions in the Model CSI-DSP95-255- PS8 manual clearly define the antenna selection and installation criteria in order to maintain a conservative 6 feet (183 cm) separation.

Compliance Worldwide, Inc. - 357 Main Street - Sandown, NH 03873 COMPLIANCE WORLDWIDE INC. TEST REPORT 247-11 In Accordance with the Requirements of FCC PART 90:2010 Issued to Cellular Specialties, Inc. 670 North Commercial Street Manchester, NH 03010 (603) 626-6677 for Bidirectional Amplifier CSI-DSP95-255-PS8 FCC ID: NVRCSIDSP95255PS8 Report Issued on July 21, 2011 Tested by This test report shall not be reproduced, except in full, without written permission from Compliance Worldwide, Inc. (603) 887 3903 Fax 887 6445 http://www.complianceworldwide.com Test Number: 247-11 Issue Date: 7/21/2011 Page 2 of 39 Compliance Worldwide, Inc. - 357 Main Street - Sandown, NH 03873 (603) 887 3903 Fax 887 6445 http://www.cw-inc.com Table of Contents 1. Scope ......................................................................................................................................... 3 2. Product Details ........................................................................................................................... 3 2.1. Manufacturer ........................................................................................................................ 3 2.2. Model Number...................................................................................................................... 3 2.3. Serial Number ...................................................................................................................... 3 2.4. Description ........................................................................................................................... 3 2.5. Power Source....................................................................................................................... 3 2.6. EMC Modifications ............................................................................................................... 3 3. Product Configuration................................................................................................................. 3 3.1. Support Equipment .............................................................................................................. 3 3.2. Cables .................................................................................................................................. 3 3.3. Operational Characteristics & Software ...............................................................................4 3.4. Block Diagram ...................................................................................................................... 4 4. Measurement Parameters.......................................................................................................... 5 4.1. Measurement Equipment Used to Perform Test ................................................................. 5 4.2. Measurement & Equipment Setup ....................................................................................... 5 4.3. Test Procedure..................................................................................................................... 5 5. Measurement Summary ............................................................................................................. 6 6. Measurement Data ..................................................................................................................... 7 6.1. Effective Radiated Power Limits 22.913 (a)........................................................................ 7 6.2. Bandwidth Limitations (FCC Part 2.1049) ........................................................................14 6.3. Spurious Emissions at the Antenna Terminals 22.917 (a)(b) ........................................... 21 6.4. Field Strength of Spurious Emissions 22.917 (a)(b) ........................................................ 30 6.5. Frequency Tolerance 22.355 ............................................................................................ 34 6.6. Inter-modulation ................................................................................................................ 35 6.7. Public Exposure to Radio Frequency Energy Levels 1.1307 (b)(1).................................. 36 7. Test Site Description ................................................................................................................ 37 Appendix A ................................................................................................................................... 38 Test Number: 247-11 Issue Date: 7/21/2011 Page 3 of 39 Compliance Worldwide, Inc. - 357 Main Street - Sandown, NH 03873 (603) 887 3903 Fax 887 6445 http://www.cw-inc.com 1. Scope This test report certifies that the Cellular Specialties DSP95-255-PS8, as tested, meets the FCC Part 2 and Part 90 Subpart I technical requirements. The scope of this test report is limited to the test sample provided by the client, only in as much as that sample represents other production units. If any significant changes are made to the unit, the changes shall be evaluated and a retest may be required. 2. Product Details 2.1. Manufacturer: Cellular Specialties 2.2. Model Number: CSI-DSP95-255-PS8 2.3. Serial Number: COC10001 2.4. Description: CSI Modular multi-band high power repeaters deliver cost effective in-building signal enhancement over a passive DAS. Large facilities can be covered without additional hardware and installation costs or the complexity of a separate fibe r DAS system. 2.5. Power Source: 120 VAC, 60 Hz 2.6. EMC Modifications: None 3. Product Configuration 3.1. Support Equipment Device Manufacturer Model Serial No. Comment Power Supply Cellular Specialties 015-2096-001-C 091100003 Notebook PC Dell Latitude D610 19472301901 Configuring Unit 3.2. Cables Cable Type LengthShieldFrom To RF, 50 Ω, N male – N male 1M Yes DUT Antenna RF, 50 Ω, N male – N male 1M Yes DUT Antenna Power Supply 2M + 2MYes DUT 120 VAC, 60 Hz Serial 1 2M Yes DUT Notebook PC USB 1 2M Yes DUT Notebook PC Ethernet 2M No DUT Note…

Text truncated - open the document above for the full version.

Test Set Up Photos – Cellular Specialties, FCC ID: NVRCSIDSP95255PS8 Radiated Front Radiated Rear