NZLJLRHL4HomeLink TX

GARAGE DOOR TRANSCEIVER WARNINGS CAUTION: Do not use the transceiver with any garage door opener that lacks the safety stop and reverse feature as required by safety standards. CAUTION: When programming the transceiver to a garage door opener or entry gate, make sure the area is clear. This will prevent potential harm or damage as the gate or garage door will activate during the program. CAUTION This device may suffer from interference if operated in the vicinity of a mobile or fixed station transmitter. This interference is likely to affect the hand-held transmitter as well as the in-car transceiver. The door transceiver is located in the rear-view mirror. It can be programmed to transmit the radio frequencies of up to 3 different transmitters, which can be used to operate garage doors, entry gates, home lighting, security systems or other radio frequency operated devices. Although this section mainly describes the procedures for a garage door opener, it equally applies to the previously mentioned applications. In some countries, this feature is also known as the HomeLink® Universal Transceiver. The transceiver radio frequency approval numbers for the USA and Canada are shown below: USA and Puerto Rico - FCC: K8597R315. Canada - CAN: 2145 101 790A. Note:HomeLink® is a registered trademark owned by the Johnson Controls, Inc. Milwaukee, Wisconsin. For further information, see See INFORMATION AND ASSISTANCE (page 7). United States of America This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Canada This device complies with Industry Canada Standard IC - RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Note:Changes or modifications not expressly approved by the manufacturer could void the user’s authority to use the equipment. BEFORE PROGRAMMING CAUTION When programming a device that may require you to press and re-press the hand-held transmitter (cycle), unplug the device during the cycling process to prevent possible motor failure. For best results, fit a new battery to the hand-held transmitter of the garage door opener (or other device) before programming. If your garage door opener receiver (located in the garage) is equipped with an antenna, make sure the antenna is hanging straight down. 5 Garage door opener PROGRAMMING E134838 With the engine switched off; 1.Make sure the ignition system is on. 2.Hold the end of the original garage door opener hand-held transmitter 2 to 6 inches (50 to 150 mm) away from the transceiver in the rear-view mirror, keeping the indicator lamp in view. 3.Using both hands, simultaneously press and hold both the chosen transceiver button on the rear-view mirror, as shown above, and the hand-held transmitter button. Keep both buttons pressed. The indicator lamp will flash slowly at first and then change to a fast flash. When the indicator lamp flashes rapidly, release both buttons. The rapid flashing lamp indicates successful programming. 4.If, after 60 seconds, the indicator lamp does not flash rapidly, release both the transceiver and the hand-held transmitter buttons and repeat the procedure starting with Step 2. Position the hand-held transmitter at a different angle and/or distance. 5.Press and hold the programmed garage door opener button and observe the indicator lamp. •If the indicator lamp illumination is continuous, programming is complete and your device should operate when the garage door opener button is pressed and held for approximately 1 to 2 seconds and then released. •If the indicator lamp blinks rapidly for 2 seconds and then illuminates continuously, proceed with the following programming instructions for rolling code device equipment. TO ERASE ALL PROGRAMMING For first time programming, make sure the engine is switched off: 1.Make sure the ignition is on (but with the engine switched off). 2.Press and hold the 2 outer buttons on the transceiver in the rear view mirror. Keep the buttons pressed until the indicator lamp begins to flash (this will take approximately 20 seconds), then release the buttons. All memories in the garage door opener have now been cleared. Note:Do not perform this procedure when programming the additional garage door opener buttons. ROLLING CODE DEVICE EQUIPMENT PROGRAMMING Note:The assistance of a second person, may make the following steps quicker and easier. Once the button has been pressed there are only 30 seconds in which to complete Step 3. 1.At the garage door opener receiver (motor head unit) in the garage, locate the learn or smart button/switch. •The name of the button or switch may vary between manufacturers. 2.Press and release the learn or smart button. 3.Return to the vehicle and firmly press and hold the programmed garage door opener button for 2 seconds and release. 4.Repeat the press, hold, release sequence three times to complete the programming process. The garage door opener in the rear view mirror should now activate the rolling code device. 6 Garage door opener REPROGRAMMING A SINGLE GARAGE DOOR OPENER BUTTON To program a device to a previously programmed button: 1.Press and hold the desired pre-programmed garage door opener button for at least 20 seconds, but no longer than 30 seconds, until the indicator lamp begins to flash. 2.Without releasing the rear-view mirror button, position the hand-held transmitter approximately 2 to 6 inches (50 to 150 mm) away from the transceiver in the rear-view mirror, keeping the indicator lamp in view. 3. Carry out Step 3 of Programming. ENTRY GATE/CANADIAN PROGRAMMING The technology of some entry gates requires you to press and re-press (cycle) the hand-held …

Text truncated - open the document above for the full version.

Exterior Mirror View Front Exterior View Mirror Assy Front Exterior View Rear

Homelink PCB Top View Homelink PCB Bottom View Homelink PCB Bottom Cover

Amber Helm Development L.C. 92723 Michigan Hwy-152 Sister Lakes, MI 49047 A copy of this Report will be on file with AHD to:January, 2023Page1 of 38 EMC Test Report #1301666FX-JLRHL4 Issued01/28/13 Regarding the FCC Part 15 testing Rear View Mirror Model Number:JLRHL4 Family Category:15.231 Transmitting Device Judgments:FCC Part 15.231 – Compliant NVLAP LAB CODE 200129-0 Prepared for:Craig Harder Gentex Corp. 600 N Centenial St Zeeland, Mi. 49464 Test Date(s):12/15/12-1/28/13 Report prepared by:Report reviewed by David J. Miller, NCEGordon L. Helm, NCE Data recorded by:_________________________ Gordon L. Helm, NCE Test Engineer, AHD Test report #1301666FX-JLRHL4Tested date: 12/16/12-1/28/13 FCC 15.231 Testing for JLRHL4 Auto Mirror Assy Family AHD EMC Lab, 92723 Michigan Hwy-152, Sister Lakes, MI 49047 (269) 429-8352 Page 2 of 38 Table of Contents Statements concerning this report ....................................................................................................3 FCC Required user statements:....................................................................................................... 4 FCC Part 18 ISM Devices: ............................................................................................................. 4 FCC Part 15 Class A or B Digital Devices or Peripherals:............................................................. 4 Industry Canada Required user statements: .................................................................................... 5 Summary of Results .........................................................................................................................7 Changes Made to Achieve Compliance:......................................................................................... 8 EUT Descriptions.............................................................................................................................9 Specifications:............................................................................................................................... 10 EUT Block Diagram: .................................................................................................................... 10 EUT Pictures ................................................................................................................................. 11 Equipment Test Setup: ...................................................................................................................15 Support Equipment & Cabling...................................................................................................... 15 Setup Pictures................................................................................................................................ 16 Measurement Report ......................................................................................................................18 Standards Applied to Test ............................................................................................................. 18 Equipment Configuration.............................................................................................................. 18 Test Methodology ......................................................................................................................... 18 Transmit: ....................................................................................................................................... 18 Receive.......................................................................................................................................... 19 Radiated: ....................................................................................................................................... 19 Variance from Test Procedure: ..................................................................................................... 19 Test Data ....................................................................................................................................... 20 Restricted Band Harmonic Peak Compliance............................................................................... 24 Receive Spurious Measurements .................................................................................................. 24 Device Deactivation...................................................................................................................... 24 Band Edge and Restricted Band Testing ...................................................................................... 25 Band Edge Testing Results Table ................................................................................................. 25 Duty Cycle .................................................................................................................................... 26 20 dB Bandwidth Measurement: .................................................................................................. 28 Training Pulse Measurement ........................................................................................................ 30 FCC SAR Calculations ................................................................................................................. 31 Environment.................................................................................................................................. 31 APPENDIX A ................................................................................................................................32 Measurement Procedures .............................................................................................................. 32 Line Conducted ............................................................................................................................. 32 Radiated ........................................................................................................................................ 33 Measure…

Text truncated - open the document above for the full version.

Radiated Prescreen Setup Front Orientation Transmit End Orientation Transmit Side Orientation Transmit