NZLUAHL5OWireless Garage Door Opener

The HomeLink® Wireless Control System provides a convenient way to replace up to three hand‐held radio‐frequency remotes used to activate devices such as gate operators, garage door openers, entry door locks, security systems, even home lighting. The below steps are generic programming instructions; for Genie and Sommer garage door openers please go directly to the HomeLink website. Additional information and programming videos can be found at www.HomeLink.com and https://homelink.com/ferrari Precautions! Before programming HomeLink to a garage door opener or gate operator, make sure that people and objects are out of the way of the device to prevent potential harm or damage. When programming a garage door opener, it is advised to park outside of the garage. Do not use HomeLink with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door that cannot detect an object signaling the door to stop and reverse does not meet current U.S. federal safety standards. It is also recommended that a new battery be placed in the hand‐held remote (garage door opener remote) of the device for quicker and more accurate training. Some vehicles may require the ignition switch to be turned on or to the “accessories” position for programming and/or operation of HomeLink. Keep the hand‐held remote (garage door opener remote) of the device you are programming for use in other vehicles as well as for future HomeLink programming. It is also suggested that upon the sale of the vehicle, the programmed HomeLink buttons be erased for security purposes. Refer to “Erasing HomeLink Buttons”. Programming a New HomeLink Button 1. Press and release the HomeLink button that you would like to program. The HomeLink indicator light will flash orange slowly (if not, refer to “Erasing HomeLink Buttons.”) 2. Position the hand‐held remote (garage door opener remote) 1 – 3 inches (2 – 8 cm) away from the HomeLink button that you would like to program. Note: Some hand‐held remotes (garage door opener remotes) may actually train better at a distance of 6 – 12 inches (15 – 20 cm). Keep this in mind if you have difficulty with the programming process. 3. While the HomeLink indicator light is flashing orange, press and hold the hand‐held remote button. Continue pressing the hand‐held remote button until the HomeLink indicator light changes from orange to green. You may now release the hand‐held remote button. Note: Some devices may require you to replace this “Programming a New HomeLink Button” step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. 4. Press the HomeLink button that you would like to program and observe the indicator light. If the indicator light remains constant green, your device should operate when the HomeLink button is pressed. At this point, if your device operates, programming is complete. If the indicator light rapidly flashes green, firmly press, hold for two seconds and release the HomeLink button up to three times to complete the programming process. At this point if your device operates, programming is complete. If the device does not operate, continue with the next step of the programming instructions. 5. At the garage door opener motor, (security gate motor, etc.) locate the “Learn,” “Smart,” or “Program” button. This can usually be found where the hanging antenna wire is attached to the motor‐head unit (see the device’s manual to identify this button). The name and color of the button may vary by manufacturer. Note: A ladder and/or second person may simplify the following steps. 6. Firmly press and release the “Learn,” “Smart,” or “Program” button. You now have 30 seconds in which to complete step 7. 7. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink button up to three times. At this point programming is complete and your device should operate when the HomeLink button is pressed and released. In the event that there are still programming difficulties or questions, additional HomeLink information and programming videos can be found at www.HomeLink.com and https://homelink.com/ferrari. For Genie and Sommer garage door openers please go directly to the HomeLink website. Gate Operator/Canadian Programming Canadian radio‐frequency laws require transmitter remote signals to “time‐out” (or quit) after several seconds of transmission, which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time‐out” in the same manner. The indicator LED on the hand‐held remote will go off when the device times out, indicating that it has finished transmitting. If you live in Canada or you are having difficulties programming a gate operator or garage door opener by using the programming procedures, replace “Programming a New HomeLink Button” step 3 with the following: While the HomeLink indicator light is flashing orange, press and release (“cycle”) your device’s hand‐held remote every two seconds until the HomeLink indicator light changes from orange to green. You may now release the hand‐held remote button. Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent possible overheating. Proceed with “Programming a New HomeLink Button” step 4 to complete. Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.). For convenience, the hand‐held remote of the device may also be used at any time. Erasing HomeLink Buttons To erase programming from the three buttons (individual buttons cannot be erased but can be “reprogrammed” as outlined below), follow the step noted: Press a…

Text truncated - open the document above for the full version.

UAHL5O UAHL5O UAHL5O UAHL5O UAHL5O UAHL5O

UAHL5O – Internal Photos UAHL5O – Internal Photos UAHL5O – Internal Photos UAHL5O – Internal Photos TX Area UAHL5O – Internal Photos UAHL5O – Internal Photos Trace Antenna

Lab Project ID#: EMC2022-10008 Test ID: Test-085067, Test-085070 Model: UAHL5O FCC Report Form for 15.231 - 3m Date: 11/4/2022 Revision: TBD Approved By: Jason Vargo Page 1 of 25 Uncontrolled copy if printed unless stamped as a Lab Controlled Document Technical Report to the FCC and ISED Regarding Gentex Corporation - HomeLink© V Model: UAHL5O FCC ID: NZLUAHL5O ISED: 4112A-UAHL5O Emission Designator: 22K6L1D 11/4/2022 A report concerning approval for Gentex Corporation Homelink® model UAHL5O Please issue grant immediately upon review. Measurements Made by: Measurements Reviewed by: Bolay Pannell Dan Brasier Laboratory Validation Engineer III Laboratory Development Engineer II Gentex Corporation Gentex Corporation Report Prepared by: Report Approved by: Patricia Klawitter Jason Vargo Laboratory Validation Engineer I Laboratory Manager I Gentex Corporation Gentex Corporation Report Submitted by: Brian Miller Laboratory Group Leader – Regulatory II Gentex Corporation Lab Project ID#: EMC2022-10008 Test ID: Test-085067, Test-085070 Model: UAHL5O FCC Report Form for 15.231 - 3m Date: 11/4/2022 Revision: TBD Approved By: Jason Vargo Page 2 of 25 Uncontrolled copy if printed unless stamped as a Lab Controlled Document Test Report Revision REV Number Date Author Description 1.0 11/4/2022 Patricia Klawitter Initial release Results relate only to the items tested as received. Compliance has been evaluated based on the Lab Manual section 7.6.2. The decision rule used regarding measurement uncertainty was to determine results solely on whether the measured values met the defined acceptance criteria without factoring in measurement uncertainty values. Lab Project ID#: EMC2022-10008 Test ID: Test-085067, Test-085070 Model: UAHL5O FCC Report Form for 15.231 - 3m Date: 11/4/2022 Revision: TBD Approved By: Jason Vargo Page 3 of 25 Uncontrolled copy if printed unless stamped as a Lab Controlled Document 1. General Information 1.1. Product Description The Gentex Corporation HomeLink® HLV Universal Garage Door Opener is a low-power transceiver OEM device that is installed into a rearview mirror. The installation is provided by trained technicians during the course of the manufacture of the automobile. It is powered by the 12 Volt system of the automobile. This Universal Garage Door Opener has the capability to 1. Learn the frequency and bit code format of the user’s existing garage door remote control devices and 2. Reproduce and transmit the frequency and bit code format to remotely operate the user’s garage door. The unit is designed for the periodic operation of a control signal, which typically activates a garage door opener receiver. The unit is supplied to the automobile manufacturer without harness. For testing purposes, a typical assembly and 2-conductor cable harness were used to power the unit. The unit is only operational when the user depresses the control button. It becomes inactive after release of the control button. The three-button HomeLink® unit replaces up to three hand-held transmitters. In addition to the typical operation of the garage door, the unit will learn the radio frequency codes of other transmitter types to activate entry door locks, estate gates, security systems, and home or office lighting. The antenna system is an integral part of the unit. It cannot be altered nor replaced by the user. Service of this system is only available from the Automobile Manufacturer’s Dealerships and Gentex Corporation. 1.2. Related Grants This device will have functionality that is covered under 47 CFR Part 15B. The device will have FCC ID # of NZLUAHL5O and ISED ID # of 4112A-UAHL5O under both rule parts. A separate report is submitted for functionality covered under 47 CFR Part 15B. 1.3. Test Methodology Radiated Emissions testing was performed according to ANSI C63.10:2013. The power source for this product is a 12V automotive vehicle battery, thus conducted emissions measurements are not required. The unit is supplied to the automobile manufacturer without harness. For testing purposes, a 2- conductor cable harness was used to interface to the unit. 1.4. Test Facility The 3-meter semi-anechoic chamber where these measurements were taken is located on the grounds of Gentex Corporation’s Corporate Labs, in the city of Zeeland, county of Ottawa, state of Michigan, United States of America. Lab Project ID#: EMC2022-10008 Test ID: Test-085067, Test-085070 Model: UAHL5O FCC Report Form for 15.231 - 3m Date: 11/4/2022 Revision: TBD Approved By: Jason Vargo Page 4 of 25 Uncontrolled copy if printed unless stamped as a Lab Controlled Document For radiated measurements above 1 GHz, RF absorbing material is placed between the antenna and EUT in accordance with ANSI C63.4:2014 Section 5.5 and chamber manufacturer’s instructions. Tabletop testing was conducted on a 3m turntable described in the site recertification report. The 3m chamber has been added to our A2LA scope of accreditation on 05/20/2016 and includes accreditation to ANSI C63.4:2014 and ANSI C63.10:2013. The report filed with ISED, dated February 11, 2015, was accepted via a letter dated February 11, 2015. Our 3m chamber is registered with the ISED under Site# 4112A-2 and FCC under registration number 357351. Corporate Mailing/Shipping Address Gentex Corporation 600 N. Centennial Street Zeeland, MI 49464 Site Address Gentex Corporation 380 Riley Street Zeeland, MI 49464 1.5. Accreditation The Gentex Corporate EMC Lab is accredited to ISO/IEC 17025 by the American Association for Laboratory Accreditation (A2LA). Our laboratory scope and accreditation certificate #2529.01 are available from their web site www.a2la.org. Our scope of accreditation covers ANSI C63.4:2014, ANSI C63.10:2013, and Radiated Emissions at 3m, FCC 47 CFR Part 15, ISED RSS-210. 2. Product Labeling 2.1. Identifiers The FCC Identifier assigned is FCC ID: NZLUAHL5O. The ISED certification number is 4112A- UAHL5O. These identifiers will be labeled on the product housing. The …

Text truncated - open the document above for the full version.

Test Setup Photos Test Setup – Above 1GHz Test Setup – Below 1GHz Test Setup Photos Test Setup – Class B Bicon Measurements Test Setup - Class B Horn Measurements Test Setup Photos Test Setup – Class B LPA Measurements End Orientation Test Setup Photos Flat Orientation Side Orientation