O7VMA191522ASB-2

ASB-2 ASB-2 SOUNDBAR ASB-2 SOUNDBAR 1 Contents Page Contents Page 1 ASB2 Connections 2 ASB2 Rear Panel 4 ASB2 Buttons 5 ASB2 Remote 6 Button Functions 7 LED Definitions 8 Features/ specifications 9 2 1 2 9 10 3 4 5 6 7 8 ASB2 Connections 3 1. HDMI Inputs used to connect upto 3 High Definition sources to the ASB2 2. HDMI output used to connect the ASB2 to the TV 3. USB Input Used to connect a USB device to the ASB2 for audio playback. 4. Digital Coaxial Input Used to connect digital coaxial audio source to the ASB2 5. Digital Optical Input Used to connect digital optical audio source to the ASB2 6. Auxiallary 1 Used to connect an analogue stereo audio source to the ASB2 using RCA phono connections. 7. Auxiallary 2 Used to connect an analogue stereo audio source to the ASB2 using a 3.5mm stereo mini jack connector. 8. Sub Out Used to connect the ASB2 to an additional sub woofer 9. Power Switch Mains Power switch. Used to turn the ASB2 on and off. 10. Mains Input Used to connect the ASB2 to the mains. ASB2 Rear Panel ASB2 Buttons 12345678910 1. Standby Used to put the ASB2 in and out of stand by mode. 2. HDMI Toggle Used to toggle through the HDMI inputs. 3. Digital Toggle Used to toggle through the digital auxialary inputs (USB, Coaxial, Optical) 4. Analogue Toggle Used to toggle through the analogue auxiallary inputs (phono and mini jack). 5. Airstream connect/ AirPlay Direct. This button serves three purposes: A single press with an iOS device connected shares wifi settings. Holding down for 12 seconds activates WPS mode. Thirdly, it will enter Airstream Connect mode if the WPS mode times out. 6. AirPlay Used to put the ASB2 into AirPlay mode. 7. 3D Used to change the sound of the ASB2 to create a 3 dimensional effect. 8. Mute Used to mute the sound from the ASB2. Pressing it again returns the volume to the previous level. 9. Volume Down Used to reduce the volume of the ASB2. 10. Volume Up Used to increase the volume of the ASB2 ASB2 Remote 1. Standby Used to put the ASB2 in and out of stand by mode. 2. Volume Up Used to increase the volume of the ASB2. 3. Previous Track Used to select the previous track of the audio source. 4. Volume Down Used to reduce the volume of the ASB2. 5. Mute Used to mute the sound from the ASB2. Pressing it again returns the volume to the previous level. 6. Menu Used to display the on screen menu of the ASB2. 7. OK & Play/ Pause Used to confirm a selection when in the menu and also used to play/ pause the audio. 8. Next Track Used to select the next track of the audio source. 9. Input Toggle Used to toggle through the various analogue and digital inputs. 16 7 8 9 2 3 4 5 Button LE D Fu nc ti on Contro l Indicati on on Ba ck lit Power Bu tt on Indicati on on Fr on t LE D ba r (RGB ) Po wer Button Backl it (Whi te / Red) PO WE R ON Si ng le Press w hen i n 'On' m ode to put un it i nt o 'S tandby' m ode WH ITE; Di m WH I TE after 3 s Change to *c ol ou r* w hen i nput cycled (* co lo ur * = based on input st ate; r efer b el ow ) Standby Si ng le Press w hen i n 'S tandb y' m ode to put un it i nt o 'ON' m ode. Soli dR ED Not Appl ic able Fa ul t Not Appl ic able Al tern at in g Flashes of W HI TE and RED @ 5 00 m s cycle PO WE R O FF Flip Pow er S wi tch w hen i n 'Off ' m ode to put un it i nt o 'S tandby' m ode Al l LED's OFF REBOOTIN‹ Not Appl ic able Flas hi ng RED @ ‹ 00 0m s ON‹ 50 0m s OF F( lo ng flash wi th s ho rt i nt er ‹a l) In u t elect (fr ont mo un te d backli t bu tt ons) No LED Se le cted Si ng le Press of F ront ‹ ounte d Inpu t Select Button s Soli d WH ITE w hen s el ecte d Change to re le ‹ant sol id *colour* w hen i np ut s el ect button presse d ( colo ba ed o i p t tate e e b elo ) Not Se le ct ed OFF w hen not se lected D DP (to p mo un te d backli t bu tt on ) WH ITE Backl ig ht Se le cted Si ng le p ress bu tt on to ac ti ‹ate Soli d WH ITE w hen s el ecte d Not Appl ic able Not Se le ct ed OFF w hen not se lected u te (to p mo un te d backli t bu tt on ) WH ITE Backl ig ht Se le cted Si ng le p ress bu tt on to mu te Soli d WH ITE w hen s el ecte d Not Appl ic able Not Se le ct ed OFF w hen not se lected P Connect (to p mo un te d backli t bu tt on ) WH ITE Backl ig ht Connecte d Si ng le p ress bu tt on to attemp t connect io n Soli d WH ITE Not Appl ic able Connec ti ng WH ITE Flash @ s‹ uare w a‹e ‹50m s cycle Not Connected OF F I R Recei er No LED Recei ‹e c om m and from r em ot e Not Appl ic able Not Appl ic able Bl inki ng *co lo ur * w hen com m and recei ‹e d ( colo c e t colo tate o o t ba Re e to ta ble belo ) o lue (to p mo un te d) No LED ‹o lu me u pP ress ‹‹‹ butt on for ‹ ol um e up Not Appl ic able ‹o lu me dow nP ress ‹‹‹ b utton fo r ‹o lu me dow n t e Ree t (r ear m ounte d) No LED Syst em Rese tS tandby and ‹ ute he ld tog et her (3s) Not Appl ic able Not Appl ic able Button Functions RBG LE D In pu t Fu nc tion Comment s In dication on Front LED bar Fr on t LE D bar Gree n AUX (A nalogue Inpu t) LINE I N- Soli d GREE N "Blink in g" a s Vo lu me pressed/IR r ec ei ved Whit e HD MI /Tosli nk/SPDIF (D ig it al Input ) DIGITAL -S ol id W HIT E "Blink in g" a s Vo lu me pressed/IR r ec ei ved Blu e Wi re le ss (A ir play / JBConnect) WI FI NOT CONNECTED ( " Wa it in g" ) Connec ti on t o av ai la bl e Wi -F i netw or k Flas hi ng BLUE @ 5 00 ms ON, 2500 ms OFF (s hort flash wi th long i nterval) - WI FI CONNECTING ( "Con nectin g" ) BLUE F la sh @ s‘u ar e wa ve 250m s c‘c le WI FI CONNECTED ( "•trea•i ng/A ir •lay rea•y" ) Soli d BLUE "Blink in g" a s Vo lu me pressed/IR r ec ei ved ‘BCONNECT Access Po in t Setu p Flas hi ng BLUE @ ‘ 00 0m s ON, 50 0m s OFF (l ong flash wi th short i nterval) - W PS/Router Set up W PS BUTT ON Wh en r ea r WP S / Connect bu tt on i s pr essed ‘o r ‘2 sec ondsB LUE Fl ash @ suar e wa ve 250m s c‘c le urp le Firm wa re Update Avai la bl e FW UPDATE AVAILABLE Wh en i s ‘ir mw are update c ar ri ed out‘W hen i s in ‘o rm at io n di sp la ‘e d b‘ LED‘Does user ac ti v at…

Text truncated - open the document above for the full version.

Caution: Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante. MPE Reminding To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de moin de 20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher à 20 cm ou moins de la position centrale de l’ antenne. La FCC des éltats-unis stipule que cet appareil doit être en tout temps éloigné d’au moins 20 cm des personnes pendant son functionnement. Technical Data Temperature Range from 15 - 35�C, Humidity: 75% Max AC input voltage: 100 - 120Vac/ 220 - 240Vac. monitoraudio.co.uk This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 1 of 3 External Picture FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 2 of 3 FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 3 of 3

Title: SB200 AMPLIFIER PANEL FRONT Artwork Date: 16th July 2013 Notes: 1.LOGOS AND TEXT TO BE SILK SCREENED COLOUR PANTONE COOL GREY 3M 2. DO NOT SILK SCREEN TEXT IN RED. TEXT FOR REFERENCE ONLY 2. IMAGE FOR REFERENCE PURPOSES ONLY. 3. VERSION 14 Label location

FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 1 of 8 Internal Picture FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 2 of 8 FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 3 of 8 FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 4 of 8 FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 5 of 8 FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 6 of 8 RF module FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 7 of 8 FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 8 of 8 Internal Antenna

FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 1 of 42 EMC TEST REPORT for Intentional Radiator No. 130401050SHA-001 Applicant : MONITOR AUDIO LTD. Unit 2, 24 Brook Road Rayleigh, Essex. England SS6 7XJ United Kingdom Manufacturer : DONGGUAN BOSUN ELECTRONIC INC. Zheng Long Industrial District, Sicun, Tangxia Town, Dongguan City, Guangdong Province, China. Equipment : Powered Speaker System Type/Model : ASB-2 SUMMARY The equipment complies with the requirements according to the following standard(s): 47CFR Part 15 (2012): Radio Frequency Devices ANSI C63.4 (2003): American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz RSS-210 Issue 8 (December 2010): Low-power Licence-exempt Radiocommunication Devices (All Frequency Bands): Category I Equipment RSS-Gen Issue 3 (December 2010): General Requirements and Information for the Certification of Radiocommunication Equipment Date of issue: May 29, 2013 Prepared by: Reviewed by: Wakeyou Wang (Project Engineer) Daniel Zhao (Reviewer) FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 2 of 42 Description of Test Facility Name: Intertek Testing Services Limited Shanghai Address: Building No.86, 1198 Qinzhou Road(North), Shanghai 200233, P.R. China FCC Registration Number: 236597 IC Assigned Code: 2042B-1 Name of contact: Steve Li Tel: +86 21 64956565 ext. 214 Fax: +86 21 54262335 ext. 214 FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 3 of 42 Content SUMMARY .......................................................................................................................................................... 1 1. GENERAL INFORMATION ............................................................................................................................ 4 1.1 Applicant Information ..................................................................................................... 4 1.2 Identification of the EUT ................................................................................................ 4 1.3 Technical specification ................................................................................................... 5 1.4 Mode of operation during the test / Test peripherals used .............................................. 5 2. TEST SPECIFICATION .................................................................................................................................. 6 2.1 Instrument list ................................................................................................................. 6 2.2 Test Standard .................................................................................................................. 6 2.3 Test Summary ................................................................................................................. 7 3. MINIMUM 6DB BANDWIDTH ....................................................................................................................... 9 3.1 Limit ................................................................................................................................ 9 3.2 Test Configuration .......................................................................................................... 9 3.3 Test Procedure and test setup .......................................................................................... 9 3.4 Test Protocol ................................................................................................................. 10 4. MAXIMUM PEAK OUTPUT POWER ............................................................................................................. 14 4.1 Test limit ....................................................................................................................... 14 4.2 Test Configuration ........................................................................................................ 14 4.3 Test procedure and test setup ........................................................................................ 14 4.4 Test protocol ................................................................................................................. 15 5. POWER SPECTRUM DENSITY ..................................................................................................................... 19 5.1 Test limit ....................................................................................................................... 19 5.2 Test Configuration ........................................................................................................ 19 5.3 Test procedure and test setup ........................................................................................ 19 5.4 Test Protocol ................................................................................................................. 20 6. RADIATED EMISSION ................................................................................................................................. 24 6.1 Test limit ....................................................................................................................... 24 6.2 Test Configuration ........................................................................................................ 24 6.3 Test procedure and test setup ........................................................................................ 25 6.4 Test protocol ................................................................................................................. 26 7. EMISSION OUTSIDE THE FREQUENCY BAND ............................................................................................. 31 7.1 Limit .............................................................................................................................. 31 7.2 Test Configuration ........................................................................................................ …

Text truncated - open the document above for the full version.

FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 1 of 3 Test Setup FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 2 of 3 1. Radiated Emission 30MHz-1000MHz FCC ID: O7VMA191522 IC: 5928A-MA191522 Page 3 of 3 Higher than 1GHz