O9EQ2686Q2686

confidential © Page : 1/ 87 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable. WISMO Quik Q2686 Product Technical Specification Reference:WM_PRJ_Q2686_PTS_001 Revision:006 Date:April 4 th 2006 Powered by the Wavecom Operating System and Open AT ® WM_PRJ_Q2686_PTS_001 April4th2006 confidential © Page : 2 / 87 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable. Document Information LevelDateHistory of the evolution 00101/17/2005Creation (Preliminary version) 00206/01/2005Pin-out modification (see chapter 3.1) 00315/09/2005Update Functional architecture Pin-out modification (see chapter 4.1) Add RESET state of all IO of all interface Update power supply range (see chapter 3.2) Update electrical information for digital IO (see chapter 3.2) Update SPI bus configuration (see chapter 3.4) Remove 3 GPIO (see chapter 3.9) Change MIC1 biasing voltage configuration (see chapter 3.11) Change SPK1 definition to only single ended (see chapter 3.11) Update ON/ÕFF operating sequence (see chapter 3.14) Update BOOT definition (see chapter 3.15) Update ~RESET operating sequence and electrical characteristics(see chapter 3.14) Update Interrupts activation (see chapter3.17) Update RTC electrical characteristics (see chapter 3.19) Update PCM description and add waveform (see chapter 3.21) 004November 22, 2005 Update Q2686 version “Overview” section Update “Cautions”, “Trademarks” and “Copyright” Update “Electrical information for digital I/O” (see chapter 3.3) Update SPI max frequency (see chapter 3.4) Update available GPIO (see chapter 3.9) Add “OFF state“ voltage caution (see chapter 3.2) Update “Battery charging interface” (see chapter 3.13) Update “Analogue audio interface” (see chapter 3.11) Update ”Environmental Specifications” (see chapter 4.2) Update “General Purpose Connector pin out description” (see chapter 4.1) 005February 2006 Update “PCM interface” waveform (see chapter 3.21) Update “Electrical information for digital IO” absolute maximum rating (see chapter 3.3) Update “General purpose connector” (see chapter 3.1) Update “SPI bus” speed (see chapter 3.4.1) Update “I²C bus” (see chapter 3.4.2) Update “Main serial link UART 1” maximum speed (see chapter 3.6) Update “Auxiliary serial link UART 2” maximum speed (see chapter 3.7) Update “SIM” General description (see chapter 3.8.1) Update “USB 2.0 interface” features (see chapter 3.22) Update “Operating system upgrade” (see chapter 6.3) Update “General purpose input / output” signals description (see chapter 3.9) Update “General purpose connector pin out description” signal description(see chapter 4.1) Update “Battery charging interface” (see chapter 3.13) Update “Analog to μDigital Converter” (see chapter 3.10) Update “FLASH-LED signal” (see chapter 3.20) Update ‘Analogue Audio interface” (see chapter 3.11) 006March 2006 Update “Power consumption” (see chapter 3.3.2) Update “ON/~OFF signal” (see chapter 3.14) Update “BAT-RTC” (see chapter 3.19) WM_PRJ_Q2686_PTS_001 April4th2006 confidential © Page : 3 / 87 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable. Update “Electrical information for digital IO” absolute maximum rating (see chapter 3.3) Update “Buzzer output” remove PWM features ( see chapter 3.12 ) Update “EMC recommendation” add ESD recommendations (see chapter 6.1.1 ) Update “SPI bus” add waveforms ( see chapter 3.4.1 ) Update “I²C bus” add waveforms ( see chapter 3.4.2 ) Update “Analog to Digital Converter“ sampling rate ( see chapter 3.10) WM_PRJ_Q2686_PTS_001 April4th2006 confidential © Page : 4 / 87 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable. WM_PRJ_Q2686_PTS_001 April4th2006 confidential © Page : 5 / 87 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable. Overview This document defines and specifies the WISMO QUIK Q2686, available under two GSM/GPRS Class 10 quad-band versions:  Q2686: EGSM/GPRS 900/1800/850/1900MHz version with 32Mb of Bursted Flash memory and 8 Mb of SRAM (32/8) WM_PRJ_Q2686_PTS_001 April4th2006 confidential © Page : 6 / 87 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable. Contents Document Information .......................................................................2 Overview............................................................................................5 Contents............................................................................................6 Table of figures................................................................................10 Cautions..........................................................................................11 Trademarks......................................................................................11 Copyright.......................................................................................…

Text truncated - open the document above for the full version.

ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH ETS Dr. Genz GmbH, Germany Registration number: «Registriernummer»-FCC_Pic Page 1 of 5 Appendix A. Pictures ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH ETS Dr. Genz GmbH, Germany Registration number: «Registriernummer»-FCC_Pic Page 2 of 5 ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH ETS Dr. Genz GmbH, Germany Registration number: «Registriernummer»-FCC_Pic Page 3 of 5

Internal use only Q2686-X60 tuning WAVECOM © 2003. All rights reserved 1 From : Erwin Dang Date : 24/04/2006 Pages : 2 To : Thierry Goupil Copy : Jacques Suires, Didier Paulin Subject : Tuning procedure FSBfiThres EFSBfiThres HSBfiThres AFSBfiThres AHSBfiThres These parameters are used when decoding a TCH speech block to determine whether the decoded block is valid. It is compared with the number of errors detected at the input of the convolutional decoding. If the number of errors is greater or equal to the BFI Error count threshold, the bad frame indicator (BFI) is set to 1. This value is different for each speech codec.
FSBfiThres : Full Rate BFI error count threshold
EFSBfiThres : Enhanced Full Rate BFI error count threshold
HSBfiThres : Half Rate BFI error count threshold
AFSBfiThres : AMR Full Rate BFI error count threshold
AHSBfiThres : AMR Half Rate error count threshold It allows a trade-off to be made between residual bit error rate and frame erasure rate To be adjusted according to the mobile in use. Recommended values: FSBfiThres : 60 EFSBfiThres : 60 HSBfiThres : 14 AFSBfiThres : 60 AHSBfiThres : 42 FacchThres This parameter is used when decoding a traffic block to determine whether a FACCH block has been received. To be adjusted according to the mobile in use. Recommended value : FacchThres : 0 HRUfiThres This parameter is used to decide if any TCH/HS block is reliable or not. The estimation of the number of erroneous demodulated bits is compared to this threshold. If the number of errors is strictly higher than this threshold the TCH/HS block is declared as unreliable. If the TCH/HS decoded block is not reliable the Unreliable Frame Indicator (UFI) is set to 1. To be adjusted according to the mobile in use. Recommended value : Internal use only Memo WAVECOM © 2003. All rights reserved 2 HRUfiThres : 36 USFMetricCS1Thres USFMetricCS24Thres This parameter is used in GPRS transfer to decide of any USF decoded on the downlink path is reliable or not. It allows the MS to compute an uplink PDCH packet on the next TDMA frame. The USF threshold value differs between coding scheme CS1 and coding schemes CS2 to CS4.
USFMetricCS1Thres : USF metric threshold for CS1
USFMetricCS24Thres : USF metric threshold for CS2, CS3 and CS4 To be adjusted according to the mobile in use. Recommended values : USFMetricCS1Thres : 23 USFMetricCS24Thres : 25 TaOffset_GSM900 TaOffset_DCS1800 TaOffset_PCS1900 TaOffset_GSM850 These parameters are used to compensate the propagation delay in the mobile’s radio system on the uplink path. This delay differs for each supported band. They are expressed in a number of quarter bits period, i.e. 12/13 MHz. Values are determined by measuring and minimizing the timing offset of TX bursts. Recommended values : TaOffset_GSM900 : 0 TaOffset_DCS180 : 0 TaOffset_PCS1900 : 0 TaOffset_GSM850 : 0 Internal use only Memo WAVECOM © 2003. All rights reserved 3 IQ_VoltageOrder BoardGain_GSM900 BoardGain_DCS1800 BoardGain_PCS1900 BoardGain_GSM850 These parameters are used to calibrate the mobile’s radio reception gain control. The actual IQ base-band signal is the result of several gain contribution:
TCH level : level of received GSM signal
BoardGain_GSM900 : static power loss in the GSM 900 radio reception stage
BoardGain_DCS1800 : static power loss in the DCS 1800 radio reception stage
BoardGain_PCS1900 : static power loss in the PCS 1900 radio reception stage
BoardGain_GSM850 : static power loss in the radio GSM 850 radio reception stage
RF Gain : dynamic radio programmable gain
IQ_VoltageOrder : expected IQ base-band input signal amplitude BoardGain_GSM900, BoardGain_DCS1800, BoardGain_PCS1900 and BoardGain_GSM850 parameters are determined using a TCH reference signal at level in the [-38;-110] dBm range. The value is computed by comparing the mobile’s power measurement with the actual TCH reference signal. This parameter is expressed in dBm. IQ_VoltageOrder value is determined to match two boundary conditions:
At reference sensitivity, it is desired to have the minimum noise figure for optimal receive sensitivity, therefore IQ signal must be maximized.
Above reference sensitivity, interferers may be present, therefore IQ signal must be reduced to avoid saturating the receive path. Recommended value : IQ_VoltageOrder : 69 RX port RF gain BoardGain_GSM900 BoardGain_DCS1800 BoardGain_PCS1900 BoardGain_GSM850 IQ_VoltageOrder TCH level IQ Internal use only Memo WAVECOM © 2003. All rights reserved 4 RoughDacValue ThinDacValue AfcStepValue This parameters are used to tune the mobile’s internal reference clock and frequency control. The frequency response of the mobile’s reference clock to the VAFC control signal is approached by a linear representation where:
RoughDacValue :is the static initial offset of the reference clock,
ThinDacValue :is the dynamic value of VAFC at wich RoughDacValue is measured,
AfcStepValue : is the approached slope value of the frequency response. ThinDacValue is chosen at the medium range of VAFC span. It is expressed in step of VAPC. RoughDacValue is a mobile internal value determined at a reference frequeny Fref by minimizing the TX burst frequency error. To determine AfcStepValue, two frequency measurements F1 and F2 are performed using TX bursts at respectively V1 and V2. Actual value is computed using a first order interpolation of F1 and F2. It is expressed in Hz. ThinDacValue RoughDacValue AfcStepValue VAFC Freq Freq V2 F1 F2 V1 Fref Internal use only Memo WAVECOM © 2003. All rights reserved 5 txPwrMinBase txPwrNMin txRampUpNbPts txRampDwnNbPts txRampUpNbNullPts txRampDwnNbNullPts txRampNmax txRampStartBase txRampStopBase txRampStart txRampStop These parameters are used to match the mobiles TX power busrt shape with each PCL template. TxRampNmax is the maximum power level. It differs for each PCL of each band. This value is expressed in TX power control DAC step. TxPwrMinBase is part of the minimum power level.…

Text truncated - open the document above for the full version.

ELECTRONIC TECHNOLOGY SYSTEMS DR. GENZ GMBH FCC - TEST - REPORT FCC RULES PARTS 22 and 24 FCC ID: O9EQ2686 Test report no.: G0M20602-0211-P-2224 Certificate 1983-01 ELECTRONIC TECHNOLOGY SYSTEMS STORKOWER STRASSE 38C, D-15526 REICHENWALDE B. BERLIN DR. GENZ GMBH PHONE +49-33631-888 00 FAX +49-33631-888 660 ETS Dr. Genz GmbH, Germany Registration number: G0M20602-0211-P-2224 Page 1 of 41 ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH TABLE OF CONTENTS 1 General information 1.1 Notes 1.2 Testing laboratory 1.3 Details of approval holder 1.4 Application details 1.5 Test item 1.6 Test standards 2 Technical test 2.1 Summary of test results 2.2 Test environment 2.3 Test equipment utilized 2.4 General Test Procedure 3 Test Results 4 RF Power Output, FCC 2.1046 4.1 Test Procedure 4.2 Test Results 5 Radiated Power FCC 22.913, FCC 24.232 5.1 Test Procedure 5.2 Test Results 6 Modulation Deviation Limiting, FCC 2.1047, 22.915(b)(c) 6.1 Test Procedure 6.2 Test Results 7 Audio Filter Characteristics, FCC 22.915(d) 7.1 Test Procedure 7.2 Test Results 8 Emission Limitations, , FCC 2.1049 8.1 Test Procedure 8.2 Test Results 9 Occupied Bandwidth FCC 22.917(b)(d); FCC 2.1049 9.1 Test Procedure 9.2 Test Results 10 Out of Band Emissions at Antenna Terminals, FCC 24.238(a) 10.1 Test Procedure 10.2 Test results 11 Spurious Radiation, FCC 2.1053, 24.236 11.1 Test Procedure 11.2 Test Results ETS Dr. Genz GmbH, Germany Registration number: G0M20602-0211-P-2224 Page 2 of 41 ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH 12 Line Conducted Emissions, FCC 15.207 12.1 Test Procedure 12.2 Test Results 13 Frequency Stability vs Temperature, FCC 2.1055, 22.355, 24. 235 13.1 Test Procedure 13.2 Test Equipment 14 Frequency Stability vs Voltage, FCC 2.1055, 22.355, 24.235 14.1 Test Procedure 14.2 Test Equipment ETS Dr. Genz GmbH, Germany Registration number: G0M20602-0211-P-2224 Page 3 of 41 ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH 1 General Information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has passed all the relevant tests conforms to a specification. Neither is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that is performance generally conforms to representative cases of communications equipment. The test results of this test report relate exclusively to the item tested as specified in 1.5. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the ELECTRONIC TECHNOLOGY SYSTEMS DR. GENZ GMBH. Tester: 07.04.2006 M. Handrik Date ETS-Lab. Name Signature Technical responsibility for area of testing: 07.04.2006 N. Kaspar Date ETS Name Signature ETS Dr. Genz GmbH, Germany Registration number: G0M20602-0211-P-2224 Page 4 of 41 ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH 1.2 Testing laboratory 1.2.1 Location ELECTRONIC TECHNOLOGY SYSTEM DR. GENZ GMBH (ETS) Storkower Straße 38c D-15526 Reichenwalde b. Berlin Germany Telephone : +49 33631 888 00 Telefax : +49 33631 888 66 1.2.2 Details of accreditation status A CCREDITED TESTING LABORATORY DAR-REGISTRATION NUMBER: DAT-P-201/96 A CCREDITED COMPETENT BODY DAR-REGISTRATION NUMBER: BPT-ZE-026/96 FCC FILED TEST LABORATORY REG. NO. 96970 BLUETOOTH QUALIFICATION TEST FACILITY (BQTF) ACCREDITED BY: BLUETOOTH QUALIFICATION REVIEW BOARD (BQRF) I NDUSTRY CANADA FILED TEST LABORATORY REG. NO. IC 3470 A2LA ACCREDITED Certificate Number: 1983-01 1.3 Details of approval holder Name : Wavecom S.A. Street : 3, esplanade du Foncet Town : 92442 Issy les Moulineaux Cedex Country : France Telephone : +33 1 4629 0800 Fax : +33 1 4629 0808 Contact : Ms. Carine Direxel E-Mail : [email protected] ETS Dr. Genz GmbH, Germany Registration number: G0M20602-0211-P-2224 Page 5 of 41 ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH 1.4 Application details Date of receipt of application : 09.02.2006 Date of receipt of test item : 09.02.2006 Date of test : 06.03.2006 – 16.03.2006 1.5 Test item Description of test item : GSM/GPRS module Type identification : Wismo Quik Q2686H Serial number : Test model without serial number. Photos : See annex A. Technical data Frequency range Tx – GSM 850 : 824.2 – 848.80 MHz Frequency range Tx – PCS : 1850.2 – 1909.8 MHz Frequency range Rx - GSM 850 : 869.2 – 893.8 MHz Frequency range Rx - PCS : 1930.2 – 1989.8 MHz Power supply : 3.8 V DC Operating mode : duplex Type of modulation : GMSK (GSM modulation) Emission : GXW Manufacturer: (if applicable) Name : Street : Town : Country : ETS Dr. Genz GmbH, Germany Registration number: G0M20602-0211-P-2224 Page 6 of 41 ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH 1.6 Test standards Technical standard : FCC Parts 22, 24, 2, 15 Additional information : Because of using the GSM 850 as an alternative technology in 850 MHz band, not all test cases of FCC Part 22 are required. This device contains 1800 MHz not operational in U.S. Territories. This filing is only applicable for 850/1900 MHz operations. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. The antenna(s) used for this transmitter must not exceed a gain of 3 dBi for mobile operation and 7 dBi for fixed operation. 2 Technical test 2.1 Summary of test results No deviations from the technical specification(s) were ascertained in the course : of the tests performed. or The deviations as specified in 2.5 were ascertained in the …

Text truncated - open the document above for the full version.

ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH ETS Dr. Genz GmbH, Germany Registration number: «Registriernummer»-FCC_Pic Page 4 of 5 ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH ETS Dr. Genz GmbH, Germany Registration number: «Registriernummer»-FCC_Pic Page 5 of 5