OKUJC9021BLUETOOTH TURNTABLE

EQ/FM/AM REPEAT/SCAN STOP/PAIR AUX IN / A U X H P T U B N S E U R B D T C IR Bluetooth Turntable Model: JC-9021 Instruction Manual FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. WARNING 3 Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC's RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installation. 4 7. Hold Down Clip PRODUCT OVERVIEW Turntable 1. Turntable Platter 2. Turntable Spindle 3. Counterweight 4. Cue Lever 5. Speed Indicator 6. Speed Selector 8. Tone Arm 9. Cartridge Front Panel 1. USB Port 2. Disc tray 3. Display 4. Remote sensor 5. AUX IN Jack 6. Power Button 7. Function Knob 8. Repeat/Scan Button 9. Rewind/Previous Button 10. Open/Close Button 11. Record/Erase Button 12. EQ/FM/AM Button 13. USB/MP3/DISC/FOLDER Buttons 14. Play/Pause/Bluetooth OUT/OK Button 15. Fast Forward/Next Button 16. Program/Memory Button 17. Stop/Pair Button 18. Volume Knob Back Panel 1. FM Antenna 2. DC IN Jack 3. Line Out Jack 1 2 3 4 5 6 7 8 10 12 13 14 16 18 9 11 15 17 DC IN 15V 1 2 3 5 1. OPEN/CLOSE button Open or close the Disc tray. 2. EQ button Change the EQ effects(NOR/ROCK/CLASS/ GAME/MOVIE/NEWS/POP/JAZZ). 3. TREBLE+/- buttons Adjust the treble effect. 4. BASS+/- buttons Adjust the bass effect. 5. button Skip to previous track. button Skip to next track. button Press and hold to rewind to the part you want to listen. button Press and hold to fast forward to the part you want to listen. button Play or pause the track. 6. STOP button Stop the tracks. 7. NUMERIC buttons Enter number to choose the desired track. 8. MUTE button Press to mute the unit, press again to resume. 9. VOL+/- buttons Adjust the volume. 10.PAIR button Press to disconnect the Bluetooth device. 11.PROGRAM button Press to program playback sequences. 12.REPEAT/SCAN button Repeat the tracks; search and store stations in Radio mode. Note: The remote control does not always function in all modes. REMOTE CONTROL 6 Essential Setup 1. Unpack the unit and remove all packaging materials. 2. Place the unit on a flat and level surface. The selected location should be stable and free from vibration. 3. Plug the power adaptor into the electrical outlet and connect another end to the back of the unit. 4. Press the Button on the upper right corner of the front panel. The display will light up and playback mode will appear on the display. 5. When the unit is playing music, the playback status will appear on the display. Panel Control /BT OUT/OK button to pause the playback, press it again to resume playback. part you want is found. USB/MP3/DISC/FOLDER Buttons to choose the folder. STOP/PAlR button to stop playing. EQ/FM/AM button on unit to change the EQ effects. REPEAT/SCAN button to select “REP 1” (repeat one) or “REP ALL” (repeat all). Note: These controls do NOT always function in all playback mode. Repeat function only works in CD and USB mode. Program Function This function enables you to set the playback of tracks into an ordered playlist. 1. Press the STOP/PAlR button; then press the PROG/MEMORY button to activate the program feature. The display will show “PROG”, “P01” and blinking “000". 2. Press the or button to select your track. 3. Press the PROG/MEMORY button again to confirm. 4. Repeat the step 2 and 3 to program other tracks. 5. After finished, press the /BT OUT/OK button to start playback. 6. Press the STOP/PAlR button once to stop. 7. Press the STOP/PAlR button twice to erase the programmed track, and “PROG" will disappear from the display. Note: automatically erase the programmed playlist. 7 Hook Belt Right Twisted Wrong location Motor Pulley 1. Unpack the unit and remove all packaging materials. 2. Place the belt on the motor pulley. Align one of the platter openings with the motor pulley, and while pulling both ends of the red ribbon that comes attached to the belt, place the belt on the motor pulley, as per the diagram. When doing this, be careful not to twist the belt. 3. Remove the red ribbon from the belt. 4. Using your hands, slowly rotate the platter 2-3 circles in a clockwise direction. This step is for resetting the auto mechanism, getting rid of any twists in the belt and making sure the belt rides smoothly along the drive rim on the underside of the platter. 5. Place the slip mat on top of the platter. Make sure the logo on the mat is facing up. Note: irregular rotation occur…

Text truncated - open the document above for the full version.

ShenzhenJunlanElectronicLtd Room201includingtheEntireBuilding,Building1,No.71LijingSouthRoad ShijingCommunity,ShijingSubdistrict,PingshanDistrict,ShenzhenCity,Guangdong Province,P.R.China TheinformationprovidedinthisletterisbasedonthereferencedrulepartsofTitle47oftheCFRaswellasKDB986446D01. Anexpirationdateforthisletterdoesnotexist.IncasetheU.S.agentchanges,thegranteeisobligatedtonotifytheFCC. FederalCommunicationsCommission AuthorizationandEvaluationDivision EquipmentAuthorizationBranch 7435OaklandMillsRoad Columbia,MD21046 ShenzhenJunlanElectronicLtd [ Room201includingtheEntireBuilding,Building1,No.71LijingSouthRoad ShijingCommunity,ShijingSubdistrict,PingshanDistrict,ShenzhenCity,GuangdongProvince,P.R.] [China] FRN:0021880893 4/24/26 U.S.AgentDesignation [ShenzhenJunlanElectronicLtd]acknowledgestheirconsentforthefollowingcontactlocatedinthe UnitedStatestoactastheiragentforserviceofprocessfortheequipmentforwhichauthorizationis sought(FCCID:OKUJC9021) NameofU.S.agent:TimPayne CompanyU.S.agent:FCCUSAgent,LLC PhysicalU.S.addressofagent:3722IllinoisAvenue,SaintCharles,IL,60174, FRNofU.S.agent:0033402884 EmailaddressofU.S.agent:[email protected] PhoneofU.S.agent: FCCUSAgent,LLCacknowledgestheirobligationtoacceptserviceofprocessonbehalfof [ShenzhenJunlanElectronicLtd]. [ShenzhenJunlanElectronicLtd]acceptsitsobligationtomaintainanagentforserviceofprocessin theUnitedStatesfornolessthanoneyearaftereitherthegranteehaspermanentlyterminatedall marketingandimportationoftheapplicableequipmentwithintheU.S.,ortheconclusionofany Commission-relatedadministrativeorjudicialproceedinginvolvingtheequipment,whicheverislater. Bysigningthisform,weconfirmtheaboveandthatweareawareoftheapplicationrequirements listedunder§2.911(d)(7). Sincerely, Signature YoukChen safetyengineer ShenzhenJunlanElectronicLtd Signature [Name] [Title] [Company] 4 8 _ [ m o d e l ] U S _ A g e n t _ 2 . 9 1 1 ( d ) ( 7 ) - U , V 0 3

Shenzhen Junlan Electronic Ltd 03‐06‐2026 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for FCC ID: OKUJC9021 Shenzhen Junlan Electronic Ltd (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, the equipment does not utilize cyber‐security or anti‐virus software from Kaspersky Lab, Inc, or any of its successors and assignees, which is also on the “covered list”. Sincerely, (Applicant signature) Youk Chen Shenzhen Junlan Electronic Ltd 03‐06‐2026 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for FCC ID: OKUJC9021 Shenzhen Junlan Electronic Ltd (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) Youk Chen

Shenzhen Junlan Electronic Ltd Date: Mar 06, 2026 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: OKUJC9021 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Long-term confidentiality: Schematics Block Diagram Operational Description Schematics.pdf Block Diagram.pdf Operational Description.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Shenzhen Junlan Electronic Ltd Youk Chen / safety engineer Typed name and Title

Shenzhen Junlan Electronic Ltd FCC ID: OKUJC9021 POWER OF ATTORNEY Date: Mar 06, 2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Testing Group Co., Ltd. (Deval Qin) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group Co., Ltd. (Deval Qin) on our behalf shall have the same effect as acts of our own. This authorization expires on Mar.05, 2027. Sincerely, Shenzhen Junlan Electronic Ltd Signature Youk Chen/ safety engineer Typed name and Title

Appendix- JC-9021-Photos Page 3 of 10 2. Photographs –Constructional Details 2.1. EUT – External View Model JC-9021 FCC ID: OKUJC9021 Appendix- JC-9021-Photos Page 4 of 10 Appendix- JC-9021-Photos Page 5 of 10 Appendix- JC-9021-Photos Page 6 of 10 Appendix- JC-9021-Photos Page 7 of 10

Label Nameplate sticker Size: 70*40mm Material: Strong self-adhesive sticker Color: Black background with white characters, surface coated with glossy varnish Location: Stick to the back of the main unit. Label Location

Appendix- JC-9021-Photos Page 8 of 10 2.2. EUT – Internal View Model JC-9021 FCC ID: OKUJC9021 Appendix- JC-9021-Photos Page 9 of 10 Appendix- JC-9021-Photos Page 10 of 10 ======End======

Waltek Testing Group Co., Ltd. http://www.waltek.com.cn Page 1 of 8 TEST REPORT Reference No. .................... : WTH26D01030377W003 FCC ID ................................ : OKUJC9021 Applicant ............................ : Shenzhen Junlan Electronic Ltd Address .............................. : Room 201 including the Entire Building, Building 1, No. 71 Lijing South Road Shijing Community, Shijing Subdistrict, Pingshan District, Shenzhen City, Guangdong Province, P.R.China Manufacturer .................... : Shenzhen Junlan Electronic Ltd Address .............................. : Room 201 including the Entire Building, Building 1, No. 71 Lijing South Road Shijing Community, Shijing Subdistrict, Pingshan District, Shenzhen City, Guangdong Province, P.R.China Product ............................... : BLUETOOTH TURNTABLE Model(s). ............................ : JC-9021 Standards........................... : FCC 47CFR Part 2 Subpart J Section 2.1091 Date of Receipt Sample .... : 2026-02-02 Date of Test........................ : 2026-02-05 to 2026-03-12 Date of Issue ...................... : 2026-04-16 Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Testing Group Co., Ltd. Address: No. 77, Houjie Section, Guantai Road, Houjie Town, Dongguan City, Guangdong, China Tel: +86-769-2267 6998 Fax: +86-769-2267 6828 Compiled by: Approved by: James Cheng / Project Engineer Deval Qin / Designated Reviewer Reference No.: WTH26D01030377W003 Page 2 of 8 Waltek Testing Group Co., Ltd. http://www.waltek.com.cn 2. Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2. CONTENTS ............................................................................................................................................................ 2 3. REVISION HISTORY ............................................................................................................................................ 3 4. GENERAL INFORMATION .................................................................................................................................. 4 4.1. GENERAL DESCRIPTION OF E.U.T. ............................................................................................................ 4 4.2. DETAILS OF E.U.T. ..................................................................................................................................... 4 4.3. TEST FACILITY ............................................................................................................................................ 5 4.4. SUBCONTRACTED ....................................................................................................................................... 5 4.5. ABNORMALITIES FROM STANDARD CONDITIONS ....................................................................................... 5 5. TEST SUMMARY .................................................................................................................................................. 6 6. RF EXPOSURE ...................................................................................................................................................... 7 6.1. REQUIREMENTS .......................................................................................................................................... 7 6.2. THE PROCEDURES / LIMIT ........................................................................................................................... 7 6.3. MPE CALCULATION METHOD .................................................................................................................... 8 6.4. RADIO FREQUENCY RADIATION EXPOSURE EVALUATION ......................................................................... 8 Reference No.: WTH26D01030377W003 Page 3 of 8 Waltek Testing Group Co., Ltd. http://www.waltek.com.cn 3. Revision History Test Report No. Date of Receipt Sample Date of Test Date of Issue Purpose Comment Approved WTH26D01030377W003 2026-02-02 2026-02-05 to 2026-03-12 2026-04-16 Original - Valid Reference No.: WTH26D01030377W003 Page 4 of 8 Waltek Testing Group Co., Ltd. http://www.waltek.com.cn 4. General Information 4.1. General Description of E.U.T. Product: BLUETOOTH TURNTABLE Model(s): JC-9021 Model Description: N/A Test Sample No.: 1-1/1 Bluetooth Version: 5.3 Hardware Version: V1.0 Software Version: V1.2.2 4.2. Details of E.U.T. Operation Frequency: 2402~2480MHz Max. RF output power: 1.49dBm Modulation Technology: GFSK, π/4DQPSK, 8DPSK Antenna installation: PCB Antenna Antenna Gain: -0.58dBi Note: #: The antenna gain is provided by the applicant, and the applicant should be responsible for its authenticity, WALTEK lab has not verified the authenticity of its information. Ratings: DC 15V/1.5A Adapter: Model: GKYZD0150150US Input: 100-240V~50/60Hz 0.8A Max Output: 15.0V 1.5A 22.5W Manufacturer: SHENZHEN SHI GUANGKAIYUAN TECHNOLOGY. LTD. Reference No.: WTH26D01030377W003 Page 5 of 8 Waltek Testing Group Co., Ltd. http://www.waltek.com.cn 4.3. Test Facility The test facility has a test site registered with the following organizations: ISED CAB identifier: CN0013. Test Firm Registration No.: 7760A. Waltek Testing Group Co., Ltd. Has been registered and fully described in a report filed with the Industry Canada. The acceptance letter from the Industry Canada is maintained in our files. Registration number 7760A, October 15, 2016. FCC Designation No.: CN1201. Test Firm Registration No.: 523476. Waltek Testing Group Co., Ltd. EMC Laboratory has been registered and fully described in a report fi…

Text truncated - open the document above for the full version.

Inverted F Antenna Specification Summary ITEMANT SPEC Model Name 2.4G ANT HorizontalVertical 2400MHz 2400MHz2500MHz2400MHz2400MHz 2500MHz Center Frequency -1.26-0.76-0.58-5.25-2.46-1.86 MAX. Gain -0.58dB PolarizationHorizontal and Vertical Azimuth Beam Pattern Omni-directional Impedance50 Ohm Antenna Length 38.20mm Manufacture ZHUHAI JIELI TECHNOLOGY CO.,LTD Antenna Photo & Length (mm) 333 Kexing Road, Xiangzhou District, Zhuhai City, Guangdong Province Address: Horizontal: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -40 Scale: 5/div Gain(dB) Frequency (MHz) Max Min Avg 2400 -1.26174 -30.0801 -7.18716 2450 -0.765802 -36.5604 -7.48023 2500 -0.585582 -22.0315 -6.59127 Vertical: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -30 Scale: 5/div Gain(dB) Frequency (MHz) Max Min Avg 2400 -5.2537 -22.1424 -12.4294 2450 -2.4652 -24.5837 -10.4702 2500 -1.86120 -29.5214 -9.20432 ANT Test Labs：Attestation of Global Compliance Co., Ltd.

Waltek Testing Group Co., Ltd. http://www.waltek.com.cn Page 1 of 78 TEST REPORT Re ference No. .................... : WTH26D01030377W002 FCC ID ................................ : OKUJC9021 Applicant ............................ : Shenzhen Junlan Electronic Ltd Address .............................. : Room 201 including the Entire Building, Building 1, No. 71 Lijing South Road Shijing Community, Shijing Subdistrict, Pingshan District, Shenzhen City, Guangdong Province, P.R.China Manufacturer .................... : Shenzhen Junlan Electronic Ltd Address .............................. : Room 201 including the Entire Building, Building 1, No. 71 Lijing South Road Shijing Community, Shijing Subdistrict, Pingshan District, Shenzhen City, Guangdong Province, P.R.China Product ............................... : BLUETOOTH TURNTABLE Model(s). ............................ : JC-9021 Standards........................... : FCC 47CFR Part 15.247 Date of Receipt Sample .... : 2026-02-02 Date of Test ....................... : 2026-02-05 to 2026-03-12 Date of Issue ...................... : 2026-04-16 Test Result ......................... : Pass Remarks: The res ults shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Testing Group Co., Ltd. Address: No. 77, Houjie Section, Guantai Road, Houjie Town, Dongguan City, Guangdong, China Tel: +86-769-2267 6998 Fax: +86-769-2267 6828 Compiled by: Approved by: James Chen g / Project Engineer Deval Qin / Designated Reviewer Reference No.: WTH26D01030377W002 Page 2 of 78 Waltek Testing Group Co., Ltd. http://www.waltek.com.cn 2 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 CONTENTS ............................................................................................................................................... 2 3 REVISION HISTORY ................................................................................................................................. 4 4 GENERAL INFORMATION ....................................................................................................................... 5 4.1 GENERAL DESCRIPTION OF E.U.T. ....................................................................................................... 5 4.2 DETAILS OF E.U.T. .............................................................................................................................. 5 4.3 CHANNEL LIST ..................................................................................................................................... 6 4.4 TEST MODE ........................................................................................................................................ 6 4.5 TEST FACILITY .................................................................................................................................... 7 5 TEST SUMMARY ...................................................................................................................................... 8 6 EQUIPMENT USED DURING TEST ......................................................................................................... 9 6.1 EQUIPMENTS LIST ............................................................................................................................... 9 6.2 DESCRIPTION OF SUPPORT UNITS ...................................................................................................... 10 6.3 MEASUREMENT UNCERTAINTY ........................................................................................................... 10 7 CONDUCTED EMISSION ....................................................................................................................... 11 7.1 E.U.T. OPERATION ............................................................................................................................ 11 7.2 EUT SETUP ...................................................................................................................................... 11 7.3 MEASUREMENT DESCRIPTION ............................................................................................................ 12 7.4 CONDUCTED EMISSION TEST RESULT ................................................................................................ 12 8 RADIATED SPURIOUS EMISSIONS ..................................................................................................... 14 8.1 EUT OPERATION ............................................................................................................................... 14 8.2 TEST SETUP ..................................................................................................................................... 15 8.3 SPECTRUM ANALYZER SETUP ............................................................................................................ 16 8.4 TEST PROCEDURE ............................................................................................................................. 1 7 8.5 CORRECTED AMPLITUDE & MARGIN CALCULATION .............................................................................. 17 8.6 SUMMARY OF TEST RESULTS ............................................................................................................. 18 9 CONDUCTED SPURIOUS EMISSIONS ................................................................................................. 21 9.1 TEST PROCEDURE ............................................................................................................................. 2 1 9.2 TEST RESULT ..............................................................................…

Text truncated - open the document above for the full version.

Appendix- JC-9021-Photos Page 1 of 10 1. Test Setup photos Model JC-9021 FCC ID: OKUJC9021 1.1 Photograph – Conducted Emission For Conducted Emission Test Site 1# 1.2 Photograph – Radiated Emissions For 9kHz-30MHz Test Site 2# Appendix- JC-9021-Photos Page 2 of 10 For 30MHz-1000MHz Test Site 2# For Above 1GHz Test Site 1#