ORH50125TPortable Beacon System

Portable Beacon System Normal Usage 1. Install the Light Posts along the desired route using the Hook & Loop Tape provided. 2. The maximum distance between each Light Post is approximately 300 feet(90 meters), based on an unobstructed view. Recommended to posting higher up on the tree trunk. 3. Remember to switch the Light Posts on before setting to desire positions. 4. Press the“On” button on key Fob, the Light Posts in range will light up 5. Light Posts will remain on for 10 minutes once activated without further FOB control input 6. Light Posts can be turned off manually at any time with the“Off” button on Key Fob and remain ready for signal receiving. 7. The “PULSE” button located on the Key FOB will transmit the signal every 1 minute for 40 minutes and then turn off. 8. After 40 minutes the last signal is sent, Light Posts will remain on for 10 minutes and then turn off light. The “PULSE” button allows a user to walk along the route activating lights without the need to continuously press the “On” button to activate the Light Posts. 9. Light Posts can be turned off manually at any time with “Off” button on Key Fob. Learning Mode While the Light Post is switched on. Function and Responses in the following situations: 1. Press and hold Program Button for 3 seconds on the Light Post then the device will enter the Learning Mode; Indication: the Light Posts will flash 3 times (rapid flashing), and then keep light on for 10 seconds 2. During the 10 seconds the Light Post is on, press the “On” button on the Key Fob while in range of the Light Post and the signal will be recorded a. If the signal is recevied: the Light Post LEDs will flash 3 times b. If no signals are detected in 10 seconds the light Post turns off and is back to normal (ready) status c. Light Post “OFF” Button is pressed The device will be switched off, user has to switch it on again to operate 3. Once procedure (2a) is completed properly, the Light Post will be able to work with the registered Key Fob. FCC STATEMENT 1. This device complies with Part 15 or the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Swiss Tech Acquisitions, LLC June 27, 2013 To: SIEMIC, INC. 775 Montague Expressway Milpitas , CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We , Swiss Tech Acquisitions, LLC hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product Description: Portable Beacon System Model name: 50125T FCC ID: ORH50125T We affirm that between SIEMIC and Swiss Tech Acquisitions, LLC , any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Client’s signature: Client’s name / title: Bennett Rubin / Vice President Contact information / address: 30725 Solon Industrial Parkway, Solon, Ohio, United States, 44139

SCS-F19: Confidentiality Request Letter Page 1 of 1 Rev 2.0 Swiss Tech Acquisitions, LLC June 27, 2013 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: ORH50125T We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Operational Description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Client’s signature: Client’s name / title: Bennett Rubin / Vice President Contact information / address: 30725 Solon Industrial Parkway, Solon, Ohio, United States, 44139

FCC Certification label location Sample Label location

FCC Certification label Sample FCC ID: ORH50125T This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Antenna

Page 1 of 32 FCC ID: ORH50125T ACCURATE TECHNOLOGY CO., LTD REPORT NO.: ATE20131229 APPLICATION CERTIFICATION On Behalf of Swiss Tech Acquisitions, LLC Portable Beacon System Model No.: 50125T FCC ID: ORH50125T Prepared for : Swiss Tech Acquisitions, LLC Address : 30725 Solon Industrial Parkway, Solon, Ohio, United States, 44139 Prepared by : ACCURATE TECHNOLOGY CO., LTD Address : F1, Bldg. A, Changyuan New Material Port, Keyuan Rd. Science & Industry Park, Nanshan, Shenzhen, Guangdong P.R. China Tel: (0755) 26503290 Fax: (0755) 26503396 Report Number : ATE20131229 Date of Test : June 18-20, 2013 Date of Report : June 25, 2013 Page 2 of 32 FCC ID: ORH50125T ACCURATE TECHNOLOGY CO., LTD REPORT NO.: ATE20131229 TABLE OF CONTENTS Description Page Test Report Certification 1. GENERAL INFORMATION .......................................................................................................... 4 1.1. Description of Device (EUT)....................................................................................................................4 1.2. Description of Test Facility ......................................................................................................................5 1.3. Measurement Uncertainty.........................................................................................................................5 2. MEASURING DEVICE AND TEST EQUIPMENT ..................................................................... 6 3. SUMMARY OF TEST RESULTS................................................................................................... 7 4. THE FIELD STRENGTH OF RADIATION EMISSION ............................................................ 8 4.1. Block Diagram of Test Setup....................................................................................................................8 4.2. The Field Strength of Radiation Emission Measurement Limits..............................................................9 4.3. Configuration of EUT on Measurement ...................................................................................................9 4.4. Operating Condition of EUT ....................................................................................................................9 4.5. Test Procedure ........................................................................................................................................10 4.6. The Field Strength of Radiation Emission Measurement Results ..........................................................11 5. 20DB OCCUPIED BANDWIDTH ................................................................................................ 13 5.1. Block Diagram of Test Setup..................................................................................................................13 5.2. The Bandwidth of Emission Limit According To FCC Part 15 Section 15.231(c) ................................13 5.3. EUT Configuration on Measurement .....................................................................................................14 5.4. Operating Condition of EUT ..................................................................................................................14 5.5. Test Procedure ........................................................................................................................................14 5.6. Measurement Result ...............................................................................................................................15 6. RELEASE TIME MEASUREMENT............................................................................................ 16 6.1. Block Diagram of Test Setup..................................................................................................................16 6.2. Release Time Measurement According To FCC Part 15 Section 15.231(a) ..........................................16 6.3. EUT Configuration on Measurement .....................................................................................................17 6.4. Operating Condition of EUT ..................................................................................................................17 6.5. Test Procedure ........................................................................................................................................17 6.6. Measurement Result ...............................................................................................................................18 7. AVERAGE FACTOR MEASUREMENT .................................................................................... 19 7.1. Block Diagram of Test Setup..................................................................................................................19 7.2. Average factor Measurement according to ANSI 63.4: 2009.................................................................19 7.3. EUT Configuration on Measurement .....................................................................................................20 7.4. Operating Condition of EUT ..................................................................................................................20 7.5. Test Procedure ........................................................................................................................................20 7.6. Measurement Result ...............................................................................................................................21 8. ANTENNA REQUIREMENT........................................................................................................ 22 8.1. The Requirement ....................................................................................................................................22 8.2. Antenna Construction .............................................................................................................................22 APP…

Text truncated - open the document above for the full version.

Radiated emissions test 30MHz- 1GHz Radiated emissions test > 1GHz