ORKTR63036-EContactless IC Card Reader / Writer

Contactless IC Card Reader/Writer TR63036(E) User’s Manual Version 0.91 2014-10-08 Toppan Forms Co., Ltd.  Copyright Toppan Forms Co., Ltd. 2014 FeliCa is a technology developed by Sony Corporation. FeliCa is a trademark of Sony Corporation. MIFARE is a trademark of NXP B.V. I-Code is a trademark of NXP B.V. All other brands, product names and trademarks are the property of their respective owners. The TM or ® markings are omitted in this document. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The contents of this document may be altered without prior notice. [TR63036(E)User’sManual] i Revision history Date Revision Description Oct/08/2014 0.91 First issue [TR63036(E)User’sManual] ii Important notice For use in the United States: 1．Module User Requirements FCC 15.212(a)(vi)(A) The host device must contain the following permanent labeling on the exterior of the host device as follows: Contains FCC ID: ORKTR63036-E FCC 15.19(a)(3) The host device shall bear the following statement in a conspicuous location on the device:This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation. When the device is so small or for such use that it is not practicable to place the statement specified under paragraph 15.19(a)(3) of this section on it, the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively,shall be placed on the container in which the device is marketed. 2．The user manual of the host device must contain the following paragraph: FCC 15.21 Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or [TR63036(E)User’sManual] iii television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. IMPORTANT NOTE: i.That module is limited to OEM installation only. ii.That OEM integrators is responsible for ensuring that the end-user has no manual instructions to remove or install module. iii.That module is limited to installation in mobile or fixed applications, according to Part 2.1091(b) iv.That separate approval is required for all other operating configurations, Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include required regulatory information/warning as below. i.End-users must be provided with transmitter/antenna installation requirements and operating conditions for satisfying RF exposure compliance. ii.A separate section should clearly state “FCC RF Exposure requirements:” iii.Required operating conditions for end users iv.Antenna/or transmitter installation requirements, where relevant (For example: The antenna used with this module must be installed to provide a separation distance of at least 20cm from all persons, and must not transmit simultaneously with any other antenna or transmitter.) [TR63036(E)User’sManual] iv For use in the EU: This device can be used without restrictions in all EU member states and EFTA countries. Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC English Hereby, Toppan Forms Co., Ltd., declares that this IC Card Reader/Writer TR63036(E) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Finnish Toppan Forms Co., Ltd. vakuuttaa täten että IC Card Reader/Writer TR63036(E) tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Dutch Hierbij verklaart Toppan Forms Co., Ltd. dat het toestel IC Card Reader/Writer TR63036E) in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG Bij deze verklaart Toppan Forms Co., Ltd. dat deze IC Card Reader/Writer TR63036(E) voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC. French Par la présente Toppan Forms Co., Ltd. déclare que l'appareil IC Card Reader/Writer TR63036(E) est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE Par la présente, Toppan Forms Co., Ltd. déclare que ce IC Card Reader/Writer TR63036(E) est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables Swedish Härmed intygar Toppan Forms Co., Ltd. att denna IC Card Reader/Writer TR63036(E) står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. Danish Undertegnede Toppan Forms Co., Ltd. erklære…

Text truncated - open the document above for the full version.

CompanyToppan Forms Co.,LTD Model NameIC Card Reader/Writer Model NumberTR63036-E FCC IDORKTR63036-E No.Result Pass Pass Pass Pass Pass Pass Pass Pass The radio elements of the modular transmitter must have their own shielding. The modular transmitter must have buffered modulation/data The modular transmitter must have its own power supply regulation. The modular transmitter must comply with the antenna and transmission system requirements of § 15.203, 15.204(b) and 15.204(c). The modular transmitter must be tested in a stand-alone configuration,i.e., the module must not be inside another device during testing for compliance with part 15 requirements. The TR63036-E complies with applicable RF exposure requirements. Signeture Dear Sir, The specific product as below, IC Card Reader/Writer, with its designed features and specified description, meets special requirements for full modular approval on FCC Part 15.212 by check list below. Modular Approval Request Letter The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.A copy of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Requirement of FCC Part 15.212 There’s an IC Card Reader/Writer that would like to have your authorization as a modular approval. The TR63036-E meets the FCC antenna requirements. It has a permanently attached antenna. The TR63036-E was tested in a stand-alone configuration. The module has its own FCC ID number. In user manual, there is warning statement to inform the customer must display a label “Contains Transmitter customer must display a label “Contains Transmitter Module FCC ID: ORKTR63036-E in enclosed module. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. Reference to TR63036-E The module has its own RF shielding. The modular has buffered data inputs. The module has its own power supply regulation. The TR63036-E is compliant with all applicable FCC rules.

1 TR63036(E) External Photos Front side Back side 2 Left-hand side Right-hand side Near side Far side

LABEL Location L A B E L

Internal Photos

e-Ohtama, Ltd., Tokyo LaboratoryTest Report Number EOTEL065 2-8-20 Kuriki, Asao-ku Kawasaki-shi, Kanagawa, JapanForm Rev. 1.00 TEL: +81-44-980-2052 Page 2 of 19 Page Cover Page.......................................................................................................................................................1 Table of Contents..............................................................................................................................................2 1.Summary ................................................................................................................................................ 3 1.1Terms and definitions .................................................................................................................... 3 1.2Standard(s) and Result.................................................................................................................. 3 1.3Deviations from Standard(s) .......................................................................................................... 4 1.4Antenna Requirements .................................................................................................................. 4 2.Equipment Under Test (EUT) ................................................................................................................. 5 2.1General Descriptions ..................................................................................................................... 5 2.2Detailed Descriptions..................................................................................................................... 5 2.3Operation Mode(s) of the EUT for EMC the Test(s) ...................................................................... 5 2.4Labeling Requirements.................................................................................................................. 6 2.5Measurement Condition ................................................................................................................ 6 3.Test Data................................................................................................................................................ 8 3.1Test specification........................................................................................................................... 8 3.220dB Bandwidth/99% Bandwidth................................................................................................... 9 3.3Frequency Stability Tolerance ..................................................................................................... 11 3.4In-Band Radiated Spurious Emission .......................................................................................... 12 3.5Out-of-Band Radiated Spurious Emission ................................................................................. 12 3.6Line Conducted Measurement Data ........................................................................................... 16 4.Photographs ......................................................................................................................................... 16 4.1Photographs of Test setup .......................................................................................................... 16 5.Test facility ........................................................................................................................................... 19 5.1Test Instruments.......................................................................................................................... 19 5.2Test equipment............................................................................................................................ 19 e-Ohtama, Ltd., Tokyo LaboratoryTest Report Number EOTEL065 2-8-20 Kuriki, Asao-ku Kawasaki-shi, Kanagawa, JapanForm Rev. 1.00 TEL: +81-44-980-2052 Page 3 of 19 1. Summary 1.1Terms and definitions AV Average DoC Declaration of Conformity EUT Equipment Under Test QP Quasi-peak 1.2Standard(s) and Result Applied Standard(s) Normative Reference(s)Test LimitFCC Part andResultReference Clause No. FCC Part15 Subpart C 20dB Bandwidth 99% Bandwidth within 13.110 - 14.010MHz15.215(c) RSS-210 A2.6 Pass3.2 Frequency Stability Tolerance 0.01% of Operating Frequency 15.225(e)Pass3.3 In-Band Emissions 15.848V/m @30m 13.553 - 13.567 MHz 334V/m @30m 13.410 - 13.553 MHz 13.567 - 13.710 MHz 106V/m @30m 13.110 - 13.410 MHz 13.710 – 14.010 MHz 15.225 (a)(b)(c)Pass3.4 Out-of-Band EmissionsEmissions outside of the specified band (13.110 - 14.010 MHz) must meet the radiated limits detailed in 15.209 15.225(d), 15.209 Pass3.5 AC Conducted Emission 150 kHz - 30 MHz FCC 15.207 limits or RSS-Gen table 2 limits> 15.207Pass3.6 Table1Standard and result e-Ohtama, Ltd., Tokyo LaboratoryTest Report Number EOTEL065 2-8-20 Kuriki, Asao-ku Kawasaki-shi, Kanagawa, JapanForm Rev. 1.00 TEL: +81-44-980-2052 Page 4 of 19 1.3Deviations from Standard(s) There was no deviation from the standard. 1.4Antenna Requirements Excerpt from §15.203 of the FCC Rules/Regulations: “An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section.” The antennas are permanently attached. There are no provisions for connection to an external antenna Conclusion: The TOPPAN FORMS CO.,LTD. IC Card Reader/Writer FCC ID: ORKTR63036-E equipment complies with the requirement of §15.203. 1.5Modular transmitter Requirements Excerpt from §15.212 of the FCC Rules/Regulations: “Single modular transmitters must meet the following requirements to obtain a modular transmitter approval.” (i) The radio elements of the modular transmitter must have their own shielding. The physical crystal …

Text truncated - open the document above for the full version.

e-Ohtama, Ltd., Tokyo LaboratoryTest Report Number EOTEL065 2-8-20 Kuriki, Asao-ku Kawasaki-shi, Kanagawa, JapanForm Rev. 1.00 TEL: +81-44-980-2052 Page 17 of 19 4.Photographs 4.1Photographs of Test Setup Photo1 Test setup for EUT Photo2 Test setup for Radiated e-Ohtama, Ltd., Tokyo LaboratoryTest Report Number EOTEL065 2-8-20 Kuriki, Asao-ku Kawasaki-shi, Kanagawa, JapanForm Rev. 1.00 TEL: +81-44-980-2052 Page 18 of 19 Photo3 Test Setup for Conducted Test_1 Front Photo4 Test Setup for Conducted Test_2 (Back)