ORMF5U1007 Port USB Hub

USB HUB 7 PORT ________________________________________ User’s Manual Table of Contents 1. Installation 1-1 Identification of Features1-2 Location1-3 Power Connection 2. Connecting the USB Hub 2-1 Connecting to your Computer 2-2 Connecting the USB cable3. Initial Connection4. Trouble Shooting5. About this Product 5-1 Do’s and Don’ts for Usage 5-2 Warranty 5-3 Features 5-4 Specifications FCC COMPLIANCE STATEMENT:This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This devicemay not cause harmful interference, and (2) this device must accept any interference received, including interference thatmay cause undesired operation.INFORMATION TO USER:This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation; if this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures:1. Reorient / Relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help.CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment 1 Installation 1-1 Identification of Features
Top Side LED 1~7 Green light is lit or blinking for each of the four ports when they are connected and active
Front of the Unit  Down Stream Ports Four, USB A-type connector ports connect to USB devices
Rear of the Unit  Up Stream Port USB B-type connector port for connection to the PC Power Socket For the AC Adapter connection Please note : ❒ Up Stream means to the PC and Down Stream means to the USB device. ❒ USB device means, a device that confirms to USB specifications. 1-2 Location The best location for the placement of this unit isbetween the USB devices to be connected, andclose enough to the PC to allow the supplied cableto reach the PC. ImportantDo not place the unit in any of the following locations: ❒ High temperature or high humidity location. ❒ A location that has a strong magnetic field. ❒ A location with excessive dust. ❒ A location that has excessive extremes in temperatures. ❒ A location that is in direct sunlight for long periods of time. ❒ A location that would cause the unit to hit or fall. ❒ A location that does not allow the unit to sit firmly and balanced on an even surface. ❒ A location that is in or near water or any type of moisture. 1-3 Power Connection ❒ Locate the unit close enough to on electrical outlet so that the AC adapter cable will reach the outletwithout putting a strain on the cable causing theadapter jack to be pulled out of the unit. ❒ It is recommended that the AC adapter be plugged into the electrical outlet first, and then plugged intothe unit . ❒ It is recommended that the AC power adapter be used at all times. Even though this unit can be selfpowered, it is only for low speed devices andmultiple devices can cause a power shortage in the unit. ❒ It is recommended that the AC adapter be used . whenever more than one hub is used in a stackingconfiguration. ❒ Do not remove the AC adapter when the unit is working. 2 Connecting the USB Hub2-1 Connecting to your computer This unit can be connected or disconnected to yourPC when the computer is on and running programs,using any USB port on your computer. This productallows your computer to interface with various USBdevices. See figure below . 3-2 Connecting the USB cable A type connector Insert the USB cable into the down stream port of the PC. Make sure that it goes all the way into thesocket and is firmly connected. B type connector Insert the USB cable into the up stream port of this product. Make sure that it goes all the way into thesocket and is firmly connected. 3 Initial Connection ❒ When connecting this unit for the first time a message box will display “Searching for unknown hardwaredevice, searching software for installation” ❒ Your computer will then start up the Device Driver Wizard, and will install the unit. This product isrecognized as “Common USB Hub” ❒ Once your computer has confirmed installation, you can then plug in whatever USB devices you wish tothe Hub. ❒ Please note that your particular software may have slightly different versions of installation software andthe message used in installing this device. 4 Trouble shooting If you encounter problems in using this product, please refer tothe following list of common problems encountered and possiblecauses. If you cannot solve the problem or it does not appear inthe list below, please contact the place of purchase for repair orreplacement. Trouble Possible Cause Computer cannot recognize One or all of the connections are this product. not firmly in the place and properly Display has a “ ! ” mark to the connected. Left side of the “ Common USB Hub” in displayed in the device manager message box Something other than “Common USB Hub” is displayed in the device Manager box. Red Power Led is not lighted on The AC adapter is not properly the unit. connected to the unit or to the outlet The outlet has no power, or is turned off Green LED light is not lighted The connection is not firmly in when port is connected to device place. Downstream USB device does The downstream USB device not fun…

Text truncated - open the document above for the full version.

ADAP SW POWER UPDNDNDNDNDN POWER SWITCH IC CHIP 5V DNDN SINGLE CHIP POWER CHANGE BUS/SELF 5V/3.3V REGI CRYSTAL Y1=6MHz

FCC ID LABEL FORMAT AND LOCATION Applicant:BELKIN COMPONENTS FCC ID:ORMF5U100 FCC ID: ORMF5U100 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID LABEL AREA


        
  
    
 
  
   
   
   
   
    
   
 
       ! "!  # #   #   !! ! $ % & ' ($ % & '   ' REPORT NO:99E8082 DATE:NOVEMBER 16, 1999 EUT:7 PORTS USB HUB FCC ID:ORMF5U100 0 OF 14

   
 
 
  

 
           
   !"#$ % This report shall not be reproduced except in full, without the written approval of CES. TABLE OF CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE..............................................1 2. PRODUCT DESCRIPTION.....................................................2 3. TESTED SYSTEM DETAILS...................................................2 4. TEST FACILITY...........................................................3 5. ACCREDITATION AND LISTING...............................................3 6. MEASUREMENT INSTRUMENTATION.............................................3 7. MEASURING INSTRUMENT CALIBRATION........................................3 8. UNITS OF MEASUREMENT....................................................4 9. ANTENNAS................................................................4 10. CLASSIFICATION OF DIGITAL DEVICE........................................4 11. RADIATED EMISSION LIMITS................................................5 12. CONDUCTED EMISSION LIMITS...............................................6 13. CONDUCTED EMISSION TEST PROCEDURE.......................................6 14. RADIATED EMISSION TEST PROCEDURE........................................6 15. AMBIENT CONDITIONS......................................................7 16. SYSTEM TEST CONFIGURATION...............................................7 17. EQUIPMENT MODIFICATIONS.................................................7 18. EUT SETUP PHOTOS............................................................8 19. TEST EQUIPMENT LIST....................................................10 20. CORRECTION FACTOR......................................................11 21. TEST RESULT SUMMARY....................................................12 APPENDICES ..................................................................14 .EXTERNAL I/O CABLE CONSTRUCTION DESCRIPTION .CONFIGURATION BLOCK DIAGRAM .CONDUCTED EMISSION PLOT .RADIATED EMISSION DATA .EUT PHOTOGRAPHS REPORT NO:99E8082 DATE:NOVEMBER 16, 1999 EUT:7 PORTS USB HUB FCC ID:ORMF5U100 1 OF 14

   
 
 
  

 
           
   !"#$ % This report shall not be reproduced except in full, without the written approval of CES. !    
 
 
     



    
          !""#   $ 
$  $#
           %   & # ' #  
 & '          
   (   
    

 
  #

   %       
  
)( " %% '   *  

#
 #
    &    #        
 & +,-,+ ./ 0,1.2/3  -/+ 1/44,3.0         ) 5 6 )! 7" 


       % 5 6  7" &'()*+'',-./0'123(42'42'5)6
*0/7.(18' 19.1'':.19':+.8'418;<*:8*0/7.(18'3.2&2&' :',-.:'0'1244'2<*:2&.12&'$


$=>;&':'4-724*<2'42.19.12&.4:'/*:2(//762*2&' /:*5-824642'03&.8&3(42'42'5*176;2&':4.0.7(:',-./0'123.771*21'8'44(:.76/:*5-8'2&'4(0' :'4-7245-'2*/:*5-82.*12*7':(18'(150'(4-:'0'12-18':2(.12.'4;

  
;; 
  

     
 
   
    

   REPORT NO:99E8082 DATE:NOVEMBER 16, 1999 EUT:7 PORTS USB HUB FCC ID:ORMF5U100 2 OF 14

   
 
 
  

 
           
   !"#$ % This report shall not be reproduced except in full, without the written approval of CES. 2. PRODUCT DESCRIPTION CHASSIS TYPE PLASTIC LIST OF EACH OSC. OR XTAL. FREQ. (FREQ.>=1 MHz) Y1=6MHz CHIPSET BRAND AND PART NO. PI, TUSB2077 NUMBER OF PCB LAYERS 4 LAYERS POWER REQUIREMENTS INPUT: 100~240V OUTPUT: DC 5V ADAPTOR NAME/MODEL/S.N. SYN, SYS1102-2005, 99A1531781 NO. OF EXTERNAL I/O CONNECTORS 8 Model Differences: Model NameDifferencesTested (Checked) F5U100 ORIGINAL MODEL NAME F5U100-MAC ADDED FOR MARKETING PURPOSES 3. TESTED SYSTEM DETAILS The Model names for all equipment, plus descriptions of all cables used in the tested system (including inserted cards) are: External Peripheral Devices Device Type ManufacturerModel NumberSerial No.FCC ID / DoC HOST COMPUTER VIVA VIVA 686-350 HS-13 DOC MONITOR COMPAQ MV500 MT-04 DOC KEYBOARD Acer 6511-TW KB-18 JVPKBS-WIN MOUSE Acer M-S34 ME-04 DZL211029 MODEM ACEEX DM-1414 MD-09 IFXDM1414 PRINTER HP C2642E PRN-05 TH93C1R2CW USB KEYBOARD CHERRY MY3000 USB 4A KB-21, 22, 23 DOC USB JOYSTICK Microsoft SideWinder Precision Pro JOY-12, 13 DOC USB HUB (EUT) BELKIN F5U100 N/A ORMF5U100 REPORT NO:99E8082 DATE:NOVEMBER 16, 1999 EUT:7 PORTS USB HUB FCC ID:ORMF5U100 3 OF 14

   
 
 
  

 
           
   !"#$ % This report shall not be reproduced except in full, without the written approval of CES. 4. TEST FACILITY The open area test sites and conducted measurement facilities used to collect the radiated data are located at No. 199, Chung Sheng Road, Hsin Tien City, Taipei, Taiwan R.O.C. The …

Text truncated - open the document above for the full version.