OU9TMB1585-BBlood Pressure Monitor

The car is locked after you press“LOCK” button. The car is unlocked after you press“UNLOCK” button. Two button USER MANUAL The car is locked after you press“LOCK” button. The car is unlocked after you press“UNLOCK” button. The car begin to enter the panic state after you press “PANIC” button. Three button The trunk is opened after you press“TRUNK” button. The car is locked after you press“LOCK” button. The car is unlocked after you press“UNLOCK” button. The car begin to enter the panic state after you press “PANIC” button. Four button The car is remote start after you press “START” button. The car is locked after you press“LOCK” button. The car is unlocked after you press“UNLOCK” button. The car begin to enter the panic state after you press “PANIC” button. Four button The car is remote start after you press “START” button. The car is locked after you press“LOCK” button. The car is unlocked after you press“UNLOCK” button. The trunk is opened after you press“TRUNK” button. This button is used to SUV(Sport Utility Vehicle). The car begin to enter the panic state after you press “PANIC” button. Five button The car is remote start after you press “START” button. The car is locked after you press“LOCK” button. The car is unlocked after you press“UNLOCK” button. The window of trunk is opened after you press this button.This button is used to SUV(Sport Utility Vehicle). The trunk is opened after you press“TRUNK” button. This button is used to SUV(Sport Utility Vehicle). The car begin to enter the panic state after you press “PANIC” button. Six button The car is remote start after you press “START” button. The car is locked after you press“LOCK” button. The car is unlocked after you press“UNLOCK” button. The right door is opened after you press this button.This button is used to MPV(Multi-Purpose Vehicle). The left door is opened after you press this button.This button is used to MPV(Multi-Purpose Vehicle). The car begin to enter the panic state after you press “PANIC” button. Six button FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution! The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device. 2.8*1.3 WUXI KYDZ CO.,LTD Model: THL-5 FCC ID: 2AE9ZTHL-5

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Model: THL-2 Photo 1   Photo 2     Photo 3   Photo 4     Photo 5   Model: THL-3 Photo 1   Photo 2     Photo 3   Photo 4     Photo 5   Model: THL-4 Photo 1   Photo 2     Photo 3   Photo 4     Photo 5   Model: THL-4 Photo 1    Photo 2     Photo 3   Photo 4     Photo 5   Model: THL-5 Photo 1   Photo 2     Photo 3   Photo 4     Photo 5   Photo 6   Model: THL-6 Photo 1   Photo 2     Photo 3   Photo 4     Photo 5   Model: THL-6 Photo 1    Photo 2     Photo 3   Photo 4     Photo 5   

2.8*1.3 WUXI KYDZ CO.,LTD Model: THL-5 FCC ID: 2AE9ZTHL-5

TÜV SÜD Certification and Testing (China) Co., Ltd. Shenzhen Branch Building 12&13, Zhiheng Wisdomland Business Park, Nantou Checkpoint Road 2, Nanshan District, Shenzhen City, 518052, P. R. China Tel. +86 755 8828 6998, Fax: +86 755 8828 5299 RF exposure Estimation for TMB-1585-BT 1. Introduction TMB-1585-BT is a Blood Pressure Monitor, which contain Bluetooth function inside. 2. Limit and Guidelines on Exposure to Electromagnetic Fields According to§15.247(e)(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. According to KDB 447498 D01 Mobile Portable RF Exposure v05r02, no SAR required if power is lower than the flowing threshold: The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where • f(GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation25 • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 3. Calculation method [(max. power of` channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 Conducted Power + tune up tolerance = 0.64mW Distance = 5 mm f = 2.480 GHz [0.64/5] * SQRT(2.480) =0.17 0.17 ≤ 3.0 Therefore, excluded from SAR testing. TUV SUD China, Shenzhen Branch Reviewed by: Prepared By: Phoebe Hu/ EMC Project Manager Calvin Weng/EMC Project Engineer Date: 2015-09-15 Date: 2015-09-15

FCC Part 15C Measurement And Test Report For WUXI KYDZ CO.,LTD. 3F, 5 Bldg, Huaqing Creative Park, Huishan Economic Development Zone, Wuxi, Jiangsu FCC ID: 2AE9ZTHL-5 Jun. 24, 2015 This Report Concerns: Original Report Equipment Type: Car remote control Report Number: MTI150513001RF Test Engineer: David Chen Reviewed By: Tim Zhang Approved & Authorized By: Hebe Lee Test Date: May 15 - Jun. 17, 2015 Prepared By: Shenzhen Microtest Technology Co.,Ltd 6F, Zhongbao Building, Gushu, Bao＇ an District, Shenzhen, P.R.China Tel: +86-755-8885 0135 Fax: +86-755-8885 0136 Note: This report shall not be reproduced except in full, without the written approval of Shenzhen Microtest Testing Lab. This document may be altered or revised by Shenzhen Microtest Testing Lab. personnel only, and shall be noted in the revision section of the document. The test results in the report only apply to the tested sample. Report No.: MTI150513001RF Page 2 of 26 Hotline: 400-666-1678 Tel: 86-755-8885 0135 Fax: 86-755-8885 0136 http://www.mtitest.com TABLE OF CONTENTS Measurement And Test Report ...................................................................... 1 1. Test Certification....................................................................................... 4 2. Test Result Summary ............................................................................... 5 3. EUT Description ........................................................................................ 6 3.1. BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED .................................................... 6 3.2. DESCRIPTION OF SUPPORT UNITS .......................................................................................................... 6 3.3. DESCRIPTION OF TEST MODE ................................................................................................................. 7 4. Facilities and Accreditations ................................................................... 8 4.1. FACILITIES ............................................................................................................................................ 8 4.2. MEASUREMENT UNCERTAINTY ............................................................................................................... 8 5. Test Results and Measurement Data ...................................................... 9 5.1. ANTENNA REQUIREMENT ........................................................................................................................ 9 6. Conducted Emission .............................................................................. 10 7. Radiated Emission Test ......................................................................... 12 7.3 EUT OPERATING CONDITIO ................................................................................................................. 15 7.4 TEST EQUIPMENT ................................................................................................................................ 15 7.5 TEST DATA ......................................................................................................................................... 15 8. Bandwidth ............................................................................................... 19 8.1 TEST STANDARD AND LIMIT .................................................................................................................. 19 8.2 TEST SETUP ........................................................................................................................................ 19 8.3 TEST PROCEDURE ................................................................................................................................ 19 8.4 EUT OPERATING CONDITION ................................................................................................................ 19 8.5 TEST EQUIPMENT ................................................................................................................................. 19 8.6 TEST CONDITION .................................................................................................................................. 20 8.7 TEST DATA .......................................................................................................................................... 20 9. Release Time Measurement ................................................................... 21 9.1 TEST STANDARD AND LIMIT .................................................................................................................. 21 9.2 TEST SETUP ........................................................................................................................................ 21 9.3 TEST PROCEDURE ................................................................................................................................ 21 9.4 EUT OPERATING CONDITION ................................................................................................................ 21 9.5 TEST EQUIPMENT ................................................................................................................................. 21 9.6 TEST CONDITION .................................................................................................................................. 22 9.7 TEST DATA .......................................................................................................................................... 22 Report No.: MTI150513001RF Page 3 of 26 Hotline: 400-666-1678 Tel: 86-755-8885 0135 Fax: 86-755-8885 0136 http://www.mtitest.com 10. Duty Cycle ............................................................................................... 23 10.1. TEST STANDARD AND LIMIT ................................................................................................................. 23 10.2. TEST SETUP ................................................................................…

Text truncated - open the document above for the full version.

1. EUT TEST PHOTO Radiated Measurement Photos