OWDTR-0037-EEDACS D3100 800 MHz Mobile Data Modem

Rhein Tech Laboratories Client: M/A COM, Inc. 360 Herndon Parkway Model: EDACS D3100 800 MHz Mobile Data Modem Suite 1400 FCC ID: OWDTR-0037-E Herndon, VA 20170 Standards: FCC Part 90/IC RSS-119 http://www.rheintech.com Report #: 2004178 36 of 44 APPENDIX K: MANUAL Please refer to the following pages. Installation and Operator’s Manual MM21134 December-04 EDACS ® D3100 RF Modem 2 REVISIO N DATE REASON FOR CHANGE - December 2004 Initial Release. M/A-COM Technical Publications would particularly appreciate feedback on any errors found in this document and suggestions on how the document could be improved. Submit your comments and suggestions to: Wireless Systems Business Unit M/A-COM, Inc. Technical Publications 221 Jefferson Ridge Parkway Lynchburg, VA 24501 or fax your comments to: (434) 455-6851 or e-mail us at: [email protected] CREDITS EDACS is a registered trademark and Failsoft and ProGrammer are trademarks of M/A-COM, Inc. Torx is a registered trademark of Camcar Innovative Solutions. All other brand and product names are trademarks, registered trademarks or service marks of their respective holders. NOTICE! This manual covers M/A-COM products manufactured and sold by M/A-COM, Inc. Repairs to this equipment should be made only by an authorized service technician or facility designated by the supplier. Any repairs, alterations, or substitution of recommended parts made by the user to this equipment not approved by the manufacturer could void the user’s authority to operate the equipment in addition to the manufacturer’s warranty. The software contained in this device is copyrighted by M/A-COM, Inc. Unpublished rights are reserved under the copyright laws of the United States. This manual is published by M/A-COM, Inc., without any warranty. Improvements and changes to this manual necessitated by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by M/A-COM, Inc., at any time and without notice. Such changes will be incorporated into new editions of this manual. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose, without the express written permission of M/A-COM, Inc. Copyright © 2004 M/A-COM, Inc. All rights reserved. 3 TABLE OF CONTENTS Page 1. RF ENERGY EXPOSURE INFORMATION............................ 4 1.1 RF ENERGY EXPOSURE AWARENESS, CONTROL INFORMATION, AND OPERATION INSTRUCTIONS FOR FCC OCCUPATIONAL USE REQUIREMENTS ..... 4 1.1.1 Federal Communications Commission Regulations .. 5 1.2 COMPLIANCE WITH RF EXPOSURE STANDARDS .... 5 1.2.1 Mobile Antennas ....................................................... 6 1.2.2 Approved Accessories ............................................... 6 1.2.3 Contact Information................................................... 7 2. SAFETY INFORMATION .......................................................... 8 2.1 COMMON HAZARDS ....................................................... 8 3. INTRODUCTION ........................................................................ 9 4. DESCRIPTION........................................................................... 10 4.1 DATA CONNECTOR FUNCTIONS ................................ 11 5. OPTIONS AND ACCESSORIES.............................................. 12 5.1 ADAPTER CABLE, CA103067V1................................... 12 6. INSTALLATION........................................................................ 14 6.1 UNPACK AND CHECK THE EQUIPMENT .................. 14 6.2 PLAN THE INSTALLATION .......................................... 14 6.3 INSTALL D3100 RF MODEM ......................................... 15 6.4 D3100 DIMENSIONS ....................................................... 16 7. WARRANTY .............................................................................. 17 1. RF ENERGY EXPOSURE INFORMATION 1.1 RF ENERGY EXPOSURE AWARENESS, CONTROL INFORMATION, AND OPERATION INSTRUCTIONS FOR FCC OCCUPATIONAL USE REQUIREMENTS Before using your mobile two-way radio, read this important RF energy awareness and control information and operational instructions to ensure compliance with the FCC’s RF exposure guidelines. NOTE This radio is intended for use in occupational/controlled conditions, where users have full knowledge of their exposure and can exercise control over their exposure to meet FCC limits. This radio device is NOT authorized for general population, consumer, or any other use. CAUTION Changes or modifications not expressly approved by M/A- COM, Inc. could void the user's authority to operate the equipment. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses RF energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, electric power, sunlight, and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which, when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All two-way radios marketed in North America are designed, manufactured, and tested to ensure they meet government established RF exposure levels. In addition, manufacturers also reco mmend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF e nergy 4 5 exposure and provide simple procedures on how to control it. Please refer to the following …

Text truncated - open the document above for the full version.

M/A-COM, Inc. 221 Jefferson Ridge Parkway Lynchburg, VA 24501 Telephone: 434.455.9527 FAX: 434.455.6851 [email protected] www.macom.com December 13, 2004 American TCB, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 Subject: FCC ID: OWDTR-0037-E New Equipment Authorization Grant CONFIDENTIALITY M/A-COM, Inc. wishes to submit this confidentiality letter for the record on FCC ID: OWDTR-0037-E 800 MHz D3100 data radio. M/A-COM, Inc. is requesting that schematic diagrams, parts lists, block diagrams, and operational descriptions for this submission not be made routinely available for public inspection. M/A-COM, Inc. considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457 and Section 0.459 of the FCC rules. Thank you for your attention to this matter. Daryl Popowitch Regulatory Manager Engineering Project Manager M/A-COM, Inc. – Lynchburg, VA

M/A-COM, Inc. 221 Jefferson Ridge Parkway Lynchburg, VA 24501 Telephone: 434.455.9527 FAX: 434.455.6851 [email protected] www.macom.com December 13, 2004 American TCB, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 Subject: FCC ID: OWDTR-0037-E New Equipment Authorization Grant M/A-COM seeks Equipment Authorization Grant on a mobile radio used for data transmission in the 800 MHz (806 - 870 MHz) band with the referenced FCC ID. The radio will operate at a rated nominal value of 3 watts and is model named D3100. Product application is mobile data collection/transmission, or utility pole mounted data transmission. Industry Canada is also requested for this equipment, using the following numbers: IC: 3636B-0037 IC model number: TR-0-037 Product application is an occupational/controlled environment, but MPE has been reported for general population/uncontrolled environment, providing a worse case value, and used as such in the User Manual. This will allow potential future application expansion without further MPE testing, if the occasion arises. Included as exhibits are internal/external photographs, user manual, test report, MPE report (measured), schematics, parts list, antenna data sheets, factory calibration procedure, etc. Confidentiality letter and Rhein Tech Laboratories, Inc. agent authorization letter, to act on M/A- COM’s behalf for this original submission, have been provided as exhibits as well. Thank you for your kind consideration and timely review of this new M/A-COM product entry. Sincerely, Daryl Popowitch Regulatory Manager, Engineering Project Manager M/A-COM, Inc. – Lynchburg, VA

M/A-COM, Inc. 221 Jefferson Ridge Parkway Lynchburg, VA 24501 Telephone: 434.455.9527 FAX: 434.455.6851 [email protected] www.macom.com December 13, 2004 To Whom It May Concern: The following organization is granted authority to act on M/A-COM’s behalf, to file technical reports, measurements, and forms for M/A-COM equipment with FCC ID: OWDTR-0037-E, 800 MHz mobile data radio equipment, as it applies to a new Equipment Authorization Grant and Industry Canada certificate; IC: 3636B-0037, model number: TR-0037. Ms. Kathy Grzovic Rhein Tech Laboratories, Inc. 360 Herndon Parkway, Suite 1400 Herndon, VA 20170 We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C.862. Further, no party, as defined in 47 CFR 1.2002(b), to the application is subject to denial of federal benefits, that includes FCC benefits. Sincerely, Daryl Popowitch Regulatory Manager, Engineering Project Manager

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 December 20, 2004 RE: FCC ID: OWDTR-0037-E_ATCB002019 Attention: Rick McMurray I have a few comments on this Application. Please note that further comments may arise in response to answers provided to the questions below. 1. Please note that occupationally source-based time-averaged values are generally done at a 50% duty cycle value. However, the manual states a 60/40% duty cycle. Please explain why the manual uses a non-standard duty cycle. 2. Please note that this device is stated in the manual as a controlled rf exposure environment. The MPE indicates that uncontrolled environment was used to produce the calculated 21cm separation. Please note that as this device is a controlled rf environment the MPE calculations for this device show a safe distance of about 8.6cm using a 2.14dBi dipole antenna. Please explain why the MPE report uses uncontrolled limits for a controlled environment device. Why was MPE measured and not simply calculated? Please report MPE using the correct rf environment limits etc. for this device. 3. Please provide a sample of your calculations for radiated spurious emissions. The numbers provided do not seem to match your provided formula for data shown on page 14 of the report. Perhaps the error is in rounding off numbers. In any event please provide a sample calculation using the provided values will clear the issue up. Dennis Ward mailto:[email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 December 20, 2004 RE: FCC ID: OWDTR-0037-E_ATCB002019 Attention: Rick McMurray I have a few comments on this Application. Please note that further comments may arise in response to answers provided to the questions below. 1. Please note that occupationally source-based time-averaged values are generally done at a 50% duty cycle value. However, the manual states a 60/40% duty cycle. Please explain why the manual uses a non-standard duty cycle. Response : This is a Data-only RF MODEM radio product. The reason for the duty cycle that we specified, i.e. 60% TX and 40% RX, is because that is theoretically the highest percentage TX that can be achieved. This is message-size dependent, with worse case representing an unending string of data being transmitted as fast as the trucked radio protocol can package it and transmit it. Any reduction of this theoretical maximum data throughput, be it time for system responses, breaks in the data source stream, or other pauses, necessarily would reduce that average TX time. 2. Please note that this device is stated in the manual as a controlled rf exposure environment. The MPE indicates that uncontrolled environment was used to produce the calculated 21cm separation. Please note that as this device is a controlled rf environment the MPE calculations for this device show a safe distance of about 8.6cm using a 2.14dBi dipole antenna. Please explain why the MPE report uses uncontrolled limits for a controlled environment device. Why was MPE measured and not simply calculated? Please report MPE using the correct rf environment limits etc. for this device. Response : a) Product application is an occupational/controlled environment, but MPE has been reported for general population/uncontrolled environment, providing a worse case value, and used as such in the User Manual. This will allow potential future application expansion without further MPE testing, if the occasion arises. Please note that this information was presented in the cover letter uploaded with this application. b) MPE was measured because this device operates in the Specialized Mobile Radio Service. Per 2.1091(c): “Mobile devices that operate in the ... Specialized Mobile Radio Service authorized under ... Part 90 of this chapter are subject to routine environmental evaluation for RF exposure prior to equipment authorization or use if they operate at frequencies of 1.5 GHz or below and their effective radiated power (ERP) is 1.5 watts or more ...” 3. Please provide a sample of your calculations for radiated spurious emissions. The numbers provided do not seem to match your provided formula for data shown on page 14 of the report. Perhaps the error is in rounding off numbers. In any event please provide a sample calculation using the provided values will clear the issue up. Response : The limit of 47.84 (47.843) was calculated from 43+10log(3.05), and the cable loss was listed at 1.6, but 1.62 was used in the actual cal culation. Discrepancies are due to rounding. Please see the following page for a sample calculation . American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 For example, the calculation for 1632 MHz: Corrected signal generator level (dBc) = conducted power – (signal generator level – CL + antenna gain) 34.85(dBm power) – (-57.4 -1.62 +4.9) = 88.97 dBc (rounded to 89.0) Margin = limit – corrected signal generator level 47.85 – 88.97 = -41.12 Dennis Ward mailto:[email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

Rhein Tech Laboratories Client: M/A COM, Inc. 360 Herndon Parkway Model: EDACS D3100 800 MHz Mobile Data Modem Suite 1400 FCC ID: OWDTR-0037-E Herndon, VA 20170 Standards: FCC Part 90/IC RSS-119 http://www.rheintech.com Report #: 2004178 39 of 44 APPENDIX M: EXTERNAL PHOTOGRAPHS PHOTOGRAPH 4: D3100 FRONT VIEW Rhein Tech Laboratories Client: M/A COM, Inc. 360 Herndon Parkway Model: EDACS D3100 800 MHz Mobile Data Modem Suite 1400 FCC ID: OWDTR-0037-E Herndon, VA 20170 Standards: FCC Part 90/IC RSS-119 http://www.rheintech.com Report #: 2004178 40 of 44 PHOTOGRAPH 5: D3100 REAR VIEW Rhein Tech Laboratories Client: M/A COM, Inc. 360 Herndon Parkway Model: EDACS D3100 800 MHz Mobile Data Modem Suite 1400 FCC ID: OWDTR-0037-E Herndon, VA 20170 Standards: FCC Part 90/IC RSS-119 http://www.rheintech.com Report #: 2004178 41 of 44 PHOTOGRAPH 6: D3100 BOTTOM VIEW

Rhein Tech Laboratories Client: M/A COM, Inc. 360 Herndon Parkway Model: EDACS D3100 800 MHz Mobile Data Modem Suite 1400 FCC ID: OWDTR-0037-E Herndon, VA 20170 Standards: FCC Part 90/IC RSS-119 http://www.rheintech.com Report #: 2004178 29 of 44 APPENDIX D: LABEL INFORMATION PHOTOGRAPH 1: FCC ID / IC ID LABEL SAMPLE AND LOCATION ON EUT BOTTOM

Rhein Tech Laboratories Client: M/A COM, Inc. 360 Herndon Parkway Model: EDACS D3100 800 MHz Mobile Data Modem Suite 1400 FCC ID: OWDTR-0037-E Herndon, VA 20170 Standards: FCC Part 90/IC RSS-119 http://www.rheintech.com Report #: 2004178 42 of 44 APPENDIX N: INTERNAL PHOTOGRAPHS PHOTOGRAPH 7: D3100 XIF-LOGIC2 Rhein Tech Laboratories Client: M/A COM, Inc. 360 Herndon Parkway Model: EDACS D3100 800 MHz Mobile Data Modem Suite 1400 FCC ID: OWDTR-0037-E Herndon, VA 20170 Standards: FCC Part 90/IC RSS-119 http://www.rheintech.com Report #: 2004178 43 of 44 PHOTOGRAPH 8: D3100 XTRS

Rhein Tech Laboratories Client: M/A COM, Inc. 360 Herndon Parkway Model: EDACS D3100 800 MHz Mobile Data Modem Suite 1400 FCC ID: OWDTR-0037-E Herndon, VA 20170 Standards: FCC Part 90/IC RSS-119 http://www.rheintech.com Report #: 2004178 44 of 44 PHOTOGRAPH 9: D3100 XPA

Engineering and Testing for EMC and Safety Compliance 360 Herndon Parkway, Suite 1400 Herndon, VA 20170 Phone 703 689-0368 Fax 703 689-2056 RF Exposure Assessment for Uncontrolled Environment Maximum Permissible Exposure Testing for M/A-COM, Inc. Model: D3100 800 MHz Modem FCC ID: OWDTR-0037-E INDUSTRY CANADA ID: 3636B-0037 M/A-COM, Inc. 221 Jefferson Ridge Parkway Lynchburg, VA 24501 USA Telephone: 434-455-9527 Contact: Daryl Popowitch November 9, 2004 Report Prepared By: Galina Yushina, Test Engineer Report Number: 2004178-004. Rev 0.00 The test results reported in this document relate only to the item that was tested. No part of this report may be reproduced, except in full, without written approval of M/A-Com, Inc. and Rhein Tech Laboratories, Inc. Engineering and Testing for EMC and Safety Compliance 360 Herndon Parkway, Suite 1400 Herndon, VA 20170 Phone 703 689-0368 Fax 703 689-2056 CONFORMANCE STATEMENT Standard(s) to which conformity is declared: STANDARDS AND OTHER APPLICABLE DOCUMENTS ENVIRONMENTAL PHENOMENA • FCC OET Bulletin 65 • FCC 47 CFR, Paragraphs 1.1310 and 2.1091 • TCB Training Material Maximum Permissible Exposure (MPE) for Uncontrolled Environment Manufacturer’s Name M/A-COM, Inc. Manufacturer’s Address 221 Jefferson Ridge Parkway Lynchburg, VA 24501 USA Device Classification Non-Broadcast Transmitter Device Type Mobile 800 MHz Radio Transceiver with Vehicle Rooftop Antenna Model Number D3100 Serial Number 9961478 FCC ID OWDTR-0037-E Industry Canada ID 3636B-0037 Mode of Operation EDACS Data (Protocol) TX Frequency Range 806 – 825 MHz RF Power Rating 3.0 Watts TX Duty Cycle 60% Antenna Type and Gain ¼-wave Monopole Antenna, 2.15 dBi Year of Manufacture 2004 We, the undersigned, hereby declare that the equipment specified above conforms to the MPE limits for uncontrolled environments required by the above identified standards at the distance referenced as the safe distance in the attached test report. No modifications were made during testing to the equipment in order to comply with the requirements of the standards. Test Personnel: Galina Yushina November 9, 2004 Test Engineer Signature Date Richard B. McMurray, P.E. November 9, 2004 Supervising Engineer Signature Date Rhein Tech Laboratories, Inc. Client: M/A-COM, Inc. 360 Herndon Parkway, Suite 1400 Model: D3100 Herndon, VA 20170 Report: 2004178-004 www.rheintech.com TABLE OF CONTENTS 1 MPE MEASUREMENTS AND FCC REGULATIONS.............................................................................................4 2 IDENTIFICATION OF THE EUT ............................................................................................................................4 3 RELATED SUBMITTAL/ GRANT ...........................................................................................................................4 4 MODIFICATIONS...................................................................................................................................................5 5 TEST LABORATORY ............................................................................................................................................5 6 TEST EQUIPMENT, TEST ACCESSORIES AND TEST SETUP ..........................................................................8 7 MPE LIMITS.........................................................................................................................................................10 8 STANDARD TEST CONDITIONS AND ENGINEERING PRACTICES ................................................................10 9 MEASUREMENT PROCEDURE.........................................................................................................................11 10 TEST RESULTS ..............................................................................................................................................12 11 CONCLUSION .................................................................................................................................................12 Rhein Tech Laboratories, Inc. Client: M/A-COM, Inc. 360 Herndon Parkway, Suite 1400 Model: D3100 Herndon, VA 20170 Report: 2004178-004 www.rheintech.com Page 4 of 12 1 MPE MEASUREMENTS AND FCC REGULATIONS This test report presents the results of Maximum Permissible Exposure (MPE) 1 testing performed on the M/A-Com, Inc. Model D3100 Modem. The tests were performed in accordance with the FCC Rules and Regulations: FCC OET Bulletin 65: “Evaluating Compliance with FCC-Specified Guidelines for Human Exposure to Radio Frequency Radiation”, Subpart I of Part 1 of 47 CFR FCC Rules and Regulations: “Procedures Implementing the National Environmental Policy Act of 1969”, Subpart J of Part 2 of 47 CFR: “Equipment Authorization Procedures”, 47 CFR paragraph 1.1310: “Radiofrequency radiation exposure limits”, 47 CFR paragraph 2.1091: “Radiofrequency radiation exposure evaluation: mobile and unlicensed devices”, and TCB training material. 2 IDENTIFICATION OF THE EUT The EUT (Equipment Under Test) is described below. Manufacturer’s Name M/A-COM, Inc. Manufacturer’s Address 221 Jefferson Ridge Parkway Lynchburg, VA 24501 USA Device Classification Modem Device Type 800 MHz Modem with Vehicle Rooftop Antenna Model Number D3100 FCC ID OWDTR-0037-E Industry Canada ID 3636B-0037 Mode of Operation EDACS data (Protocol) TX Frequency Range 806 – 825 MHz RF Power Rating 3.0 Watts TX Duty Cycle 60%. Antenna(s) Type(s) and Gain(s) Vehicle Rooftop Antenna: Quarter Wave Vertical, Model: AN102800V1; Gain - 2.15 dBi Year of Manufacture 2004 3 RELATED SUBMITTALS/ GRANTS • FCC ID: OWDTR-0037-E • Industry Canada ID: 3636B-0037 1 By definition, maximum permissible exposure (MPE) is rms or peak electric (or magnetic) field strength, or the plane-wave equivalent power densities associated with these fields to which a person may be exposed without harmful effect and with an acceptable safety factor. Rhein Tech Laboratories, Inc. Client: M/A-COM, Inc. 360 H…

Text truncated - open the document above for the full version.

Engineering and Testing for EMC and Safety Compliance T T Y Y P P E E C C E E R R T T I I F F I I C C A A T T I I O O N N R R E E P P O O R R T T M/A-COM, Inc. 221 Jefferson Ridge Parkway Lynchburg, VA 28061 Daryl Popowitch Phone: (434) 455-9527 E-Mail: [email protected] MODEL: EDACS D3100 800 MHz Data Modem TR-0037 FCC ID: OWDTR-0037-E IC: 36363B-0037 December 1, 2004 STANDARDS REFERENCED FOR THIS REPORT PART 2: 2003 FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS PART 15: 2003 RADIO FREQUENCY DEVICES - §15.109: RADIATED EMISSIONS LIMITS PART 22: 2003 PUBLIC MOBILE SERVICES PART 74: 2003 EXPERIMENTAL RADIO, AUXILIARY, SPECIAL BROADCAST AND OTHER PROGRAM DISTRIBUTIONAL SERVICES PART 90: 2003 PRIVATE LAND PORTABLE RADIO SERVICES ANSI C63.4-2003 A MERICAN NATIONAL STANDARD FOR METHODS OF MEASUREMENT OF RADIO NOISE EMISSIONS FROM LOW –VOLTAGE ELECTRICAL AND ELECTRONIC EQUIPMENT IN THE RANGE OF 9 KHZ – 40 GHZ ANSI/TIA/EIA603- 2002 L AND PORTABLE FM OR PM COMMUNICATIONS EQUIPMENT – MEASUREMENT AND PERFORMANCE STANDARDS ANSI/TIA/EIA –102.CAAA; 2002 D IGITAL C4FM/CQPSK TRANSCEIVER MEASUREMENT METHODS RSS-119; Issue 6; 2000 LAND PORTABLE AND FIXED RADIO TRANSMITTERS AND RECEIVERS 27.41 TO 960.0 MHZ ICES-003: 1997 SPECTRUM MANAGEMENT; INTERFERENCE-CAUSING EQUIPMENT STANDARD – DIGITAL APPARATUS Frequency Range Maximum Measured Output Power (W) Conducted Measured Frequency Tolerance (ppm) Emission Designator 806-824 MHz 3.05 0.6 14K2F1D (2 level WB 9600) 806-824 MHz 3.05 0.6 13K4F1D (2 level NPSPAC 9600) REPORT PREPARED BY TEST ENGINEER: DAN BIGGS Document Number: 2004178/ QRTL04-278 This report may not be reproduced, except in full, without the full written approval of Rhein Tech Laboratories, Inc. Test results relate only to the item tested. Rhein Tech Laboratories Client: M/A COM, Inc. 360 Herndon Parkway Model: EDACS D3100 800 MHz Mobile Data Modem Suite 1400 FCC ID: OWDTR-0037-E Herndon, VA 20170 Standards: FCC Part 90/IC RSS-119 http://www.rheintech.com Report #: 2004178 2 of 44 T ABLE OF CONTENTS 1 GENERAL INFORMATION..........................................................................................................................................................................5 1.1 TEST FACILITY....................................................................................................................................................................................................................5 1.2 RELATED SUBMITTAL(S)/GRANT(S) ................................................................................................................................................................................5 2 CONFORMANCE STATEMENT................................................................................................................................................................6 3 TESTED SYSTEM DETAILS.......................................................................................................................................................................7 4 FCC RULES AND REGULATIONS PART 2 §2.1033(C)(8) VOLTAGES AND CURRENTS THROUGH THE FINAL AMPLIFYING STAGE.....................................................................................................................................................................................8 5 FCC RULES AND REGULATIONS PART 2 §2.1046 (A): RF POWER OUTPUT: CONDUCTED; RSS-119 §6.2: OUTPUT POWER TEST...............................................................................................................................................................................9 5.1 TEST PROCEDURE ............................................................................................................................................................................................................9 5.2 TEST DATA..........................................................................................................................................................................................................................9 6 FCC RULES AND REGULATIONS PART 2 §2.1051: SPURIOUS EMISSIONS AT ANTENNA TERMINALS; RSS- 119 §6.3: UNWANTED EMISSIONS.....................................................................................................................................................10 6.1 TEST PROCEDURE ..........................................................................................................................................................................................................10 6.2 TEST DATA........................................................................................................................................................................................................................10 7 FCC RULES AND REGULATIONS PART 2 §2.1053 (A): FIELD STRENGTH OF SPURIOUS RADIATION; RSS- 119 §6.3: UNWANTED EMISSIONS.....................................................................................................................................................14 7.1 TEST PROCEDURE ..........................................................................................................................................................................................................14 7.2 TEST DATA........................................................................................................................................................................................................................14 7.2.1 CFR 47 PART 90.210 REQUIREMENTS..............................................................................................................................................................14 8 FCC RULES AND REGULATIONS PART 2 §2.1049 (C) (1): OCCUPIED B…

Text truncated - open the document above for the full version.