P4E-SMARTPIN-7Card Reader and Fingerprint Scanner

i SmartTOUCH TM Xtreme Manual Installation and operation March 20th 2007 Version 1.0 ii iii This manual is applicable for the following SmartID TM products: o 800-2410 SmartTOUCH TM Xtreme Remark: This manual is based on software version 2.14 this version supports the storage of one fingerprint template only. This document contains preliminary information regarding storage of two templates. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) that this device does not cause harmful interference, and 2) that this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the manufacturer could void the user's authority to loperate the equipment iv 1.1 General information This document describes the installation procedure and operating instructions of the SmartTOUCH TM Xtreme combined ISO 14443 and biometric finger print reader. Certificate: CE : pending FCC : pending Consult your National Authority if any listings are needed for this product. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) that this device does not cause harmful interference, and 2) that this device must accept any interference received, including interference that may cause undesired operation. Copyright notice: Copyright © Integrated Engineering 2003, 2004, 2005, 2006, 2007. All rights reserved. No part of this document may be reproduced, translated into another language, stored in a retrieval system or transmitted in any form or by any means electronic, mechanical, photocopying, recording or otherwise without the prior written consent of Integrated Engineering. Disclaimer: The information in this document is subject to change without prior notification. Every precaution has been taken in the preparation of this document. Integrated Engineering assumes no responsibility for errors or omissions. Neither any liability will be assumed for direct or indirect damages resulting from the use of the information contained in this document. Trademarks: SmartID TM , SmartLOGON TM , and SmartTOUCH TM are trademarks of Integrated Engineering. MIFAREÆ is a registered trademark of Philips Royal Electronics N.V. 1. Introduction v Table of Contents 1. Introduction iv 1.1 General information iv 2. SmartTOUCH TM Xtreme 1 2.1 Introduction 1 2.1.1 Electrical Connections 1 2.1.2 Access Control Data format 1 2.1.3 ISO 14443 Cards 2 2.1.4 Components 2 2.2 Installation 2 2.2.1 Mounting and connections 2 2.2.2 Initializing the Reader 3 2.3 Using SmartTOUCH TM Xtreme 3 2.3.1 Enroll mode: storing a fingerscan template in an ISO 14443 card 3 2.3.2 Access mode: Obtaining access 4 2.3.3 Erase mode: Erasing an ISO 14443 card 5 2.4 The Enroll card and the Erase card 6 2.4.1 Activating an Enroll card and an Erase card 6 2.4.2 Programming an Enroll card/Erase card 6 2.5 Requirements for ISO 14443 Cards 7 2.6 Appendix 8 2.6.1 SmartTOUCH TM Xtreme initialization sequence 8 2.6.2 SmartTOUCH TM Xtreme LED behavior 8 2.6.3 Possible Errors 9 2.6.4 SmartTOUCH TM Xtreme and other SmartTOUCH TM readers. 10 Short product specifications and part numbers/article codes 11 Cable Distance 11 SIA recommended cable type for Wiegand signals 11 Wiegand Signal Levels 12 Reader output interface and pull-up resistors 12 3. Drawings 15 Figure 1: Drawing 71309764, SmartTOUCH TM Xtreme: mounting and installation 15 1 2.1 Introduction The SmartTOUCH TM Xtreme reader is an access control proximity reader, which provides a higher level of security: an authorized card alone is not sufficient to obtain access. A fingerprint of the cardholder, which must agree with the template stored on the card, is also required. Use of a card by unauthorized personnel is therefore not possible. The SmartTOUCH TM Xtreme reader is a combination of an ISO 14443 reader and a FingerScan module. The SmartTOUCH TM Xtreme reader makes it possible to store fingerprint templates on ISO 14443 cards in Enroll mode and verifies cards in Access Control mode. After comparing the stored template with the fingerscan of the user, the access control information in the card is sent to an external system. The external system is completely independent of the fingerprint information, which is only stored on the userís card and no where else. This prevents problems with the privacy regulations. The reader is built with a narrow housing to provide easy mounting next to doors. Please note that the reader has to be mounted on the correct height for presenting the finger to the reader. The backplate is prepared for mounting the reader on a European of US wall socket. The SmartTOUCH TM Xtreme is prepared for outside use. For extreme, low temperature conditions an optional heater is needed. This document describes the installation procedure, the functions, and the specifications of the SmartTOUCH TM Xtreme reader. The information in this document is based on the software version V102. Please note that the SmartTOUCH TM Xtreme uses minutea based templates. The SmartTOUCH TM Xtreme templates are incompatable with the templates of the SmartID and Classic SmartTOUCH TM readers. 2.1.1 Electrical Connections The SmartTOUCH TM Xtreme reader is an identification and verification unit to be used in combination with an external system. For installation and connections see Figure 1: Drawing 71309764, SmartTOUCHTM Xtreme: mounting and installation and Table 1: SmartTOUCHTM Xtreme connector assignements. 2.1.2 Access Control Data format The reader can read two types of data: the serial number of the card, or data that is stored in the card. The data transfer protocol can be determined by information on the card itself or by the configuration of the reader. The SmartTOUCH TM Xtreme reader supports: • clock and data ABA track 2 emulation • Wiegand • Clock and Data • RS232 / RS422 / RS485 read-only output and • PDP-1 RS485 multi-drop…

Text truncated - open the document above for the full version.

TNO Electronic Products & Services (EPS) B.V. Smidshornerweg 18 P.O. Box 15 9822 ZG Niekerk The Netherlands www.eps-tno.com T +31 594 505005 F +31 594 504804 E [email protected] Subject Cover letter Date September 14, 2007 Our reference 07053104.B1 1 Your reference - Page 1 of 1 Our General Terms and Conditions, as filed at the Chamber of Commerce in Groningen, are applicable to all orders given to TNO Electronic Products & Services (EPS) B.V. TNO Electronic Products & Services (EPS) B.V. is registered at the Chamber of Commerce in Groningen with no. 27247331. Return address: P.O. Box 15, 9822 ZG Niekerk, The Netherlands ATCB Att. Mrs. M. Bosley Certification Department 6731 Whittier Avenue, Suite C110 McLean, Virginia 22101 USA Dear Mrs. Bosley: On behalf of our customer Integrated Engineering we would like to apply for an FCC certification of the following device: FCC ID : P4E-SMARTPIN-7 Brand : Integrated Engineering Model : SmartTOUCH Exreme Description : 13.56 MHz Inductive Proximity Card Reader with finger scan module. The following PDF files (exhibits) are electronically submitted: 1. Cover letter (this letter). 2. Request for confidentiality 3. Authorization letter 4. Form 731 5. Antenna information 6. Bill of materials 7. Block diagram 8. Circuit diagram 9. Interior photographs 10. Exterior photographs 11. Label information 12. Operational description 13. Test report in conformity with 47 CFR Part 15 14. Test setup photographs 15. User manual Best regards, TNO Electronic Products & Services (EPS) B.V. P. de Beer Approvals & Quality Manager

TNO Electronic Products & Services (EPS) B.V. Smidshornerweg 18 P.O. Box 15 9822 ZG Niekerk The Netherlands www.tno-eps.com T +31 594 505005 F +31 594 504804 E [email protected] Subject Request for confidentiality Date September 14, 2007 Our reference 07053104.B12 Your reference - Page 1 of 1 Our General Terms and Conditions, as filed at the Chamber of Commerce in Groningen, are applicable to all orders given to TNO Electronic Products & Services (EPS) B.V. TNO Electronic Products & Services (EPS) B.V. is registered at the Chamber of Commerce in Groningen with no. 27247331. Return address: P.O. Box 15, 9822 ZG Niekerk, The Netherlands ATCB Att. Mrs. M. Bosley Certification Department 6731 Whittier Avenue, Suite C110 McLean, Virginia 22101 USA Dear Mrs. Bosley: Pursuant to section 0.457 of the FCC rules we herewith request the following exhibits, rela ted to this application for FCC ID: P4E-SMARTPIN-7, to be withheld from public inspection and to be kept confidential. The contents of these exhibits may not be disclosed to otherparties than Integrated Engineering and TNO Electronic Products & 1. Bill of materials 2. Circuit diagram 3. Block diagram 4. Theory of operation The reason for this request for confidentiality is that the information contained in the exhibits as listed above has been classified as company confidential. Disclosure of any portion of this information to other parties would cause substantial competitive harm. Best regards, TNO Electronic Products & Services (EPS) B.V. P. de Beer Approvals & Quality Manager

To whom it may concern, This letter confirms the agreement that: TNO Electronic Products & Services (EPS) B.V. Smidshornerweg 18 9822 TL Niekerk The Netherlands Phone number: +31 594 505005 Fax number: +31 594 504814 is authorized as an agent for Integrated Engineering BV Paasheuvelweg 20 1105 BJ Amsterdam The Netherlands This agent authorization includes: -signing application forms and act on behalf of Integrated Engineering BV -receiving and exchanging data between Integrated Engineering BV and worldwide national authorities regarding the -certification of- and/or -arranging type approvals for the following product: proximity readers for access control and other purposes. This authorization will expire on December 31, 2007 or upon earlier written notice from Integrated Engineering BV. Yours sincerely,

ANTENNA To whom it may concern, Amsterdam, February 5 th 2007 Integrated Engineering BV Paasheuvelweg 20 1105 BJ Amsterdam The Netherlands We declare that the antenna on the Smartreader board mounted in the SmartTOUCH Xtreme (ISO14443) (13.56 MHz) access control reader is a magnetic loop antenna printed on PCB. Yours sincerely, Ir R.J.Holslag

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 September 19, 2007 RE: Integrated Engineering B.V. FCC ID: P4E-SMARTPIN-7 I have a few comments on this Application. Depending on your responses, kindly understand there may be additional comments. 1.) Please indicate where I may find the 15.21 Information to User statement in the Manual. 2.) Unless you tell me otherwise, I will call this device a “Card Reader and Fingerprint Scanner” on the Grant. Is this acceptable? 3.) FYI: It is always helpful to provide some sort of occupied bandwidth spectrum plot in all Unlicensed radio equipment test reports. This is also a requirement recommended by ANSI C63.4. Kindly remember this detail for all future Test Reports. William H. Graff President mailto: [email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

TNO Electronic Products & Services (EPS) B.V. Smidshornerweg 18 P.O. Box 15 9822 ZG Niekerk The Netherlands www.tno-eps.com T +31 594 505005 F +31 594 504804 E [email protected] Subject Integrated Engineering P4E-SMARTPIN-7 Date September 25, 2007 Our reference 07053104.B13 Your reference Integrated Engineering Page 1 of 1 Our General Terms and Conditions, as filed at the Chamber of Commerce in Groningen, are applicable to all orders given to TNO Electronic Products & Services (EPS) B.V. TNO Electronic Products & Services (EPS) B.V. is registered at the Chamber of Commerce in Groningen with no. 27247331. Return address: P.O. Box 15, 9822 ZG Niekerk, The Netherlands ATCB Attn.: W.H. Graff Certification Department 6731 Whittier Avenue, Suite C110 McLean, Virginia 22101 USA Dear Mr. W. H. Graff, Please find our response on your questions related to our filing for our customer Integrated Engineering related to P4E-SMARTPIN-7 Your question: 1.) Please indicate where I may find the 15.21 Information to User statement in the Manual. Our response: A modified Manual has been added. The proper 15.21 text has been added on page iii 2.) Unless you tell me otherwise, I will call this device a “Card Reader and Fingerprint Scanner” on the Grant. Is this acceptable? Our response: Since all related products (see all P4E grants on the FCC site) are called “Inductive Proximity Card Reader” we would suggest: “Inductive Proximity Card Reader and Fingerprint Scanner”. If this name has to many characters, then your name is acceptable. 3.) FYI: It is always helpful to provide some sort of occupied bandwidth spectrum plot Unlicensed radio equipment test reports. This is also a requirement recommended by C63.4. Kindly remember this detail for all future Test Reports. Our response: Thank you for your suggestion. We will provide future test reports with these plots. Best regards, TNO Electronic Products & Services (EPS) B.V. Pieter de Beer Quality & Approval Manager

Testing and certification of, consultancy and research concerning, electronic and electric appliances, systems, installations and telecommunication systems EXTERIOR PHOTOGRAPHS OF A BIOMETRIC FINGERPRINT READER WITH 13.56 MHZ INDUCTIVE PROXIMITY CARD READER, OPERATING ON 13.56 MHZ, BRAND INTEGRATED ENGINEERING, MODEL SMARTTOUCH XTREME TM FCC listed Industry Canada VCCI Registered R&TTE, LVD, EMC Notified Body : : : : 90828 IC3501 R-1518, C-1598 1856 TNO Electronic Products & Services (EPS) B.V. P.O. Box 15 9822 ZG Niekerk (NL) Smidshornerweg 18 9822 TL Niekerk (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 Internet: www.tno-eps.com E-mail: [email protected] Project number: 07053104.P01 Page 1 of 8 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 Description of test item Test item : Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Manufacturer : Integrated Engineering B.V. Brand mark : Integrated Engineering Model : SmartTOUCH Xtreme TM Serial number(s) : n.a. Applicant information Applicant’s representative : Ir. R. Holslag Company : Integrated Engineering B.V. Address : Paasheuvelweg 20 Postal code : 1105 BJ City : Amsterdam Country : The Netherlands Telephone number : +31 (0) 20 46 20 755 Telefax number : +31 (0) 20 46 20 756 Project number: 07053104.P01 Page 2 of 8 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 Table of contents 1 Photographs of the equipment................................................................................................................................................4 1.1 Front view......................................................................................................................................................................4 1.2 Top view.........................................................................................................................................................................5 1.3 Bottom view...................................................................................................................................................................6 1.4 Side view........................................................................................................................................................................7 1.5 Rare view........................................................................................................................................................................8 Project number: 07053104.P01 Page 3 of 8 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 1 Photographs of the equipment 1.1 Front view Project number: 07053104.P01 Page 4 of 8 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 1.2 Top view Project number: 07053104.P01 Page 5 of 8 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 1.3 Bottom view Project number: 07053104.P01 Page 6 of 8 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 1.4 Side view Project number: 07053104.P01 Page 7 of 8 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 Project number: 07053104.P01 Page 8 of 8 1.5 Rare view

SmartTOUCH Xtreme – Mifare FCC-ID: P4E-SMARTPIN-7 P/N: 800-2420 V1.03 YR-WK-S/N:07-20-1111 Conf: 01SMR-1000 Enroll code: 00000001 SmartTOUCH Xtreme – DF FCC-ID: P4E-SMARTPIN-7 P/N: 800-2422 V1.03 YR-WK-S/N:07-20-1111 Conf: 01SMR-1000 Enroll code: 00000001 SmartTOUCH Xtreme – DF PIVII FCC-ID: P4E-SMARTPIN-7 P/N: 800-2421 V1.03 YR-WK-S/N:07-20-1111 Conf: 01SMR-1000 Enroll code: 00000001

Testing and certification of, consultancy and research concerning, electronic and electric appliances, systems, installations and telecommunication systems TNO Electronic Products & Services (EPS) B.V. P.O. Box 15 9822 ZG Niekerk (NL) Smidshornerweg 18 9822 TL Niekerk (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 Internet: www.tno-eps.com E-mail: [email protected] Project number: 07053104.P02 Page 1 of 17 INTERIOR PHOTOGRAPHS OF A BIOMETRIC FINGERPRINT READER WITH 13.56 MHZ INDUCTIVE PROXIMITY CARD READER, OPERATING ON 13.56 MHZ, BRAND INTEGRATED ENGINEERING, MODEL SMARTTOUCH TM XTREME FCC listed Industry Canada VCCI Registered R&TTE, LVD, EMC Notified Body : : : : 90828 IC3501 R-1518, C-1598 1856 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 Project number: 07053104.P02 Page 2 of 17 Description of test item Test item : Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Manufacturer : Integrated Engineering B.V. Brand mark : Integrated Engineering Model : SmartTOUCH TM Xtreme Serial number(s) : n.a. Applicant information Applicantís representative : Ir. R. Holslag Company : Integrated Engineering B.V. Address : Paasheuvelweg 20 Postal code : 1105 BJ City : Amsterdam Country : The Netherlands Telephone number : +31 (0) 20 46 20 755 Telefax number : +31 (0) 20 46 20 756 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 Project number: 07053104.P02 Page 3 of 17 Table of contents 1 Photographs of the equipment ................................................................................................................................................4 1.1 Front view ......................................................................................................................................................................4 1.2 Overview ........................................................................................................................................................................5 1.3 Host ................................................................................................................................................................................6 1.4 Host rare view ................................................................................................................................................................7 1.5 Heater print component side...........................................................................................................................................8 1.6 Heater print rare side ......................................................................................................................................................9 1.7 Finger print processor...................................................................................................................................................10 1.8 Finger print processor...................................................................................................................................................11 1.9 Finger print detector print (top) ....................................................................................................................................12 1.10 Finger print detector print (rare) ...................................................................................................................................13 1.11 Keypad .........................................................................................................................................................................14 1.12 Keypad (rare)................................................................................................................................................................15 1.13 Transmitter 13.56MHz .................................................................................................................................................16 1.14 Transmitter rare view ...................................................................................................................................................17 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 Project number: 07053104.P02 Page 4 of 17 1 Photographs of the equipment 1.1 Front view Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 Project number: 07053104.P02 Page 5 of 17 1.2 Overview Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 Project number: 07053104.P02 Page 6 of 17 1.3 Host Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 Project number: 07053104.P02 Page 7 of 17 1.4 Host rare view Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 Project number: 07053104.P02 Page 8 of 17 1.5 Heater print component side Description of EUT: Manufacturer: Brand mark: Model: FCC ID: Biometric Fingerprint Reader with 13.56 MHz…

Text truncated - open the document above for the full version.

Testing and certification of, consultancy and research concerning, electronic and electric appliances, systems, installations and telecommunication systems TNO Electronic Products & Services (EPS) B.V. P.O. Box 15 9822 ZG Niekerk (NL) Smidshornerweg 18 9822 TL Niekerk (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 E-mail: [email protected] Web: www.tno-eps.com Project number: 07053104.fcc-SmartTOUCH TM Xtreme Page 1 of 14 TEST REPORT CONCERNING THE COMPLIANCE OF A BIOMETRIC FINGERPRINT READER WITH 13.56 MHZ INDUCTIVE PROXIMITY CARD READER, OPERATING ON 13.56 MHZ, BRAND INTEGRATED ENGINEERING, MODEL SMARTTOUCH TM XTREME, WITH 47 CFR PART 15 (AUGUST 14, 2006). FCC listed Industry Canada R&TTE, LVD, EMC Notified Body : : : 90828 IC3501 1856 Test specification(s): Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 47 CFR Part 15 (2006-02-01) Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 Project number 07053104.fcc.SmartTOUCH TM Xtreme Page 2 of 14 MEASUREMENT/TECHNICAL REPORT Integrated Engineering B.V. Model : SmartTOUCH TM Xtreme FCC ID: P4E-SMARTPIN-7 August 22, 2007 This report concerns: Original grant/certification Class 2 change Verification Equipment type: Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader (DesFire PIV/Mifare) cards Deferred grant requested per 47 CFR 0.457(d)(1)(ii) ? Yes No n.a. Report prepared by: Name : Ties E.T. Koning Company name : TNO Electronic Products & Services (EPS) B.V. Address : Smidshornerweg 18 Postal code/city : 9822 ZG Niekerk Mailing address : P.O. Box 15 Postal code/city : 9822 TL Niekerk Country : The Netherlands Telephone number : + 31 594 505 005 Telefax number : + 31 594 504 804 E-mail : [email protected] The data taken for this test and report herein was done in accordance with 47 CFR Part 15 (August 14, 2006) and the measurement procedures of ANSI C63.4-2003. TNO Electronic Products & Services (EPS) B.V. at Niekerk, The Netherlands, certifies that the data is accurate and contains a true representation of the emission profile of the Equipment Under Test (EUT) on the date of the test as noted in the test report. I have reviewed the test report and find it to be an accurate description of the test(s) performed and the EUT so tested. Date: August 22, 2007 Signature: H.J. Pieters Project Manager TNO Electronic Products & Services (EPS) B.V. Test specification(s): Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 47 CFR Part 15 (2006-02-01) Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 Project number 07053104.fcc.SmartTOUCH TM Xtreme Page 3 of 14 Description of test item Test item : Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Manufacturer : Integrated Engineering B.V. Brand : Integrated Engineering Model : SmartTOUCH TM Xtreme Serial number(s) : n.a. Revision : n.a. Receipt date : July 12, 2007 Applicant information Applicant's representative : Ir. R. Holslag Company : Integrated Engineering B.V. Address : Paasheuvelweg 20 Postal code : 1105 BJ City : Amsterdam PO-box : - Postal code : - City : - Country : The Netherlands Telephone number : +31 (0) 20 46 20 755 Telefax number : +31 (0) 20 46 20 756 Test(s) performed Location : Niekerk Test(s) started : July 17, 2007 Test(s) completed : August 17, 2007 Purpose of test(s) : Equipment Authorisation (Original grant/certification) Test specification(s) : 47 CFR Part 15 (August 14, 2006) Test engineers : Ties E.T. Koning Report written by : Ties E.T. Koning. Report date : August 22, 2007 This report is in conformity with NEN-EN-ISO/IEC 17025: 2005 This report shall not be reproduced, except in full, without the written permission of TNO Electronic Products & Services (EPS) B.V. The test results relate only to the item(s) tested. Test specification(s): Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 47 CFR Part 15 (2006-02-01) Biometric Fingerprint Reader with 13.56 MHz Inductive Proximity Card Reader Integrated Engineering BV Integrated Engineering SmartTOUCH TM Xtreme P4E-SMARTPIN-7 Project number 07053104.fcc.SmartTOUCH TM Xtreme Page 4 of 14 Table of contents 1 General information. ..............................................................................................................................................................5 1.1 Product description.........................................................................................................................................................5 1.1.1 Introduction. ...........................................................................................................................................................5 1.2 Related submittal(s) and/or Grant(s). .............................................................................................................................5 1.2.1 General. ..................................................................................................................................................................5 1.2.2 FCC ID P4E-SMARTPIN-8. ..................................................................................................................................5 1.3 Tested system details............................................................................................................…

Text truncated - open the document above for the full version.