P4M-AMD120Tablet PC

1 2 Compliance Information FCC Notice The following statement applies to all products that have received FCC approval. Applicable products bear the FCC logo, and/or an FCC ID in the format FCC ID: P4M-AMD120 on the product label. The mobile device complies with part of 15 of the FCC rules. Operation is subject to the following two conditions: (1) This mobile device may not cause harmful interference, and (2) this mobile device must accept any interference received, including interference that may cause undesirable operation. This mobile device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The Antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter. RF Exposure Information (FCC SAR) DEVICE MEETS THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Governments. The exposure standard for wireless mobile devices employees a unit of measurement known as the Specific Absorption Rage, or SAR. The SAR limit set by the FCC is 1.6W/kg. Test for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating cane be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the poser required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The highest SAR value for the device as reported to the FCC when tested for use when worn on the body, as described in this guide, is 0.657W/kg (Body- worn measurements differ among device models, depending upon available accessories and FCC requirements.) 3 While there may be difference between the SAR levels of various devices and at various positions, they all meet the government requirement. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant Section of www.fcc.gov/oet/ea/fccid/ after searching on FCC ID: P4M-AMD120 4 Contents What’s in the Box............................................................................................................................................ 6 Before Getting Started ................................................................................................................................... 6 Charging the Battery ....................................................................................................................................... 7 Welcome to Android ...................................................................................................................................... 9 Setting your location preferences .................................................................................................................. 9 Signing into your Google account ................................................................................................................. 10 Home and Android basics ............................................................................................................................. 11 Using the Touchscreen ................................................................................................................................. 12 Monitoring your Tablet’s status ................................................................................................................... 13 Status Icons ................................................................................................................................................... 13 Notification Icons ......................................................................................................................................... 13 Working with Quick settings ......................................................................................................................... 14 Securing your tablet ..................................................................................................................................... 15 Encrypt your tablet ....................................................................................................................................... 15 Customizing the Homescreen ....................................................................................................................... 16 Changing Homescreen Wal…

Text truncated - open the document above for the full version.

External photos of EUT Front view of EUT Rear view of EUT Side view of EUT

FCC Label 1. FCC Label Drawing Label will be attached on the bottom side of EUT. The label is visible after detach battery cover. Battery Model: AMD120 FCC ID: P4M‐AMD120 Made in CHINA

Internal photos of EUT Internal view Top view of main board Top view of main board (without shield cap) Bottom view of main board Bottom view of main board ( without shield cap) WLAN BT Antenna

Report File No. : F690501/RF-SAR001955-A1 Date of Issue : 2011-10-05 Page : 2 / 56 Contents 1. General Information 1.1 Testing Laboratory........................................................................................... 3 1.2 Details of Applicant.......................................................................................... 3 1.3 Version of Report............................................................................................. 3 1.4 Description of EUT(s)....................................................................................... 3 1.5 Test Environment............................................................................................. 4 1.6 Operation description........................................................................................ 4 1.7 Evaluation procedures....................................................................................... 5 1.8 The SAR Measurement System............................................................................ 6 1.9 System Components.......................................................................................... 8 1.10 SAR System Verification.................................................................................... 9 1.11 Tissue Simulant Fluid for the Frequency Band.......................................................... 11 1.12 Test Standards and Limits.................................................................................. 12 1.13 Justification for Extended SAR Dipole Calibrations................................................... 13 2. Instruments List.................................................................................... 14 3. Summary of Results................................................................................ 15 3.1 FCC Power Measurement Procedures..................................................................... 15 3.2 RF Conducted Power........................................................................................ 15 3.3 SAR Test Configuration...................................................................................... 17 3.4 SAR Data Summary.......................................................................................... 19 APPENDIX A. DASY4 SAR Report B. Uncertainty Analysis C. Calibration certificate Report File No. : F690501/RF-SAR001955-A1 Date of Issue : 2011-10-05 Page : 3 / 56 1. General Information 1.1 Testing Laboratory SGS Korea Co., Ltd. (Gunpo Laboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, 435-040, Korea Telephone : +82 +31 428 5700 FAX : +82 +31 427 2371 Homepage : www.kr.sgs.com/ee 1.2 Details of Applicant Applicant : AnyDATA Corporation. Address : 5 Oldfield, Irvine, CA, 92602 Email : [email protected] Phone No. : 949-900-6040 1.3 Version of Report Version Number Date Revision 00 2011-08-25 Initial issue 01 2011-10-05 Revision 01 1.4 Description of EUT(s) EUT Type : Tablet PC Model : AMD120 FCC ID : P4M-AMD120 Serial Number : 0228433 Mode of Operation : WLAN Duty Cycle : 1(WLAN) Body worn Accessory : None Tx Frequency Range : 2412 MHz ~ 2462 MHz (WLAN) 2402 MHz ~ 2480 MHz (Bluetooth) Conducted Max Power : 15.01 dBm (WLAN), -3.40 dBm(Bluetooth) Report File No. : F690501/RF-SAR001955-A1 Date of Issue : 2011-10-05 Page : 4 / 56 1.5 Test Environment Ambient temperature : (22 ± 2) ° C Tissue Simulating Liquid : (22 ± 2) ° C Relative Humidity : (55 ± 5) % R.H. 1.6 Operation Configuration The client provided a special driver and test program which can control the frequency and power of the WLAN. Measurements were performed at the lowest, middle and highest channels of the operating band. The EUT was set to maximum power level during all tests and at the beginning of each test the battery was fully charged. The DASY4 system measures power drift during SAR testing by comparing e-field in the same location at the beginning and at the end of measurement. Report File No. : F690501/RF-SAR001955-A1 Date of Issue : 2011-10-05 Page : 5 / 56 1.7 EVALUATION PROCEDURES - Power Reference Measurement Procedures The Power Reference Measurement and Power Drift Measurements are for monitoring the power drift of the device under test in the batch process. The Minimum distance of probe sensors to surface determines the closest measurement point to phantom surface. The minimum distance of probe sensors to surface is 4 mm. This distance cannot be smaller than the Distance of sensor calibration points to probe tip as defined in the probe properties (for example, 2.7 mm for an ET3DV6 probe type). - The entire evaluation of the spatial peak values is performed within the Post-processing engine (SEMCAD). The system always gives the maximum values for the 1 g and 10 g cubes. The algorithm to find the cube with highest averaged SAR is divided into the following stages: 1. The extraction of the measured data (grid and values) from the Zoom Scan. 2. The calculation of the SAR value at every measurement point based on all stored data (A/D values and measurement parameters) 3. The generation of a high-resolution mesh within the measured volume 4. The interpolation of all measured values from the measurement grid to the high-resolution grid 5. The extrapolation of the entire 3-D field distribution to the phantom surface over the distance from sensor to surface 6. The calculation of the averaged SAR within masses of 1 g and 10 g. The probe is calibrated at the center of the dipole sensors that is located 1 mm to 2.7 mm away from the probe tip. During measurements, the probe stops shortly above the phantom surface, depending on the probe and the surface detecting system. Both distances are included as parameters in the probe configuration file. The software always knows exactly how far away the measured point is from the surface. As the probe cannot directly measure at the surface, the values between the deepest measured point and the surface must be extrapolated. The angle between the probe axis an…

Text truncated - open the document above for the full version.

Report Number: F690501/RF-RTL004915-1 Page: 2 of 46 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory)18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371www.kr.sgs.com/ee INDEX Table of contents 1. General information --------------------------------------------------------------------------------------3 2. Transmitter radiated spurious emissions and conducted spurious emission --------------6 3. 6 ໒ bandwidth ------------------------------------------------------------------------------------------- 25 4. Maximum peak output power --------------------------------------------------------------------------32 5. Power Spectral Density --------------------------------------------------------------------------------- 34 6. Transmitter AC Power Line Conducted Emission-------------------------------------------------41 7. Antenna Requirement ----------------------------------------------------------------------------------- 46 Report Number: F690501/RF-RTL004915-1 Page: 3 of 46 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.kr.sgs.com/ee 1. General Information 1.1. Testing Laboratory SGS Korea Co., Ltd.(Gunpo Laboratory) - 705, Dongchun-Dong Sooji-Gu, Yongin-Shi, Kyungki-Do, South Korea. - Wireless Div. 2FL, 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea 435-040 www.kr.sgs.com/ee Telephone : +82 +31 428 5700 FAX : +82 +31 427 2371 1.2. Details of Applicant Applicant : AnyDATA Corporation Address : 5 Oldfield, Irvine, CA, 92602 Contact Person : Kevin Kim Contact Number : 949-900-6040 1.3. Description of EUT Kind of Product Tablet PC Model Name AMD120 Serial Number N / A Power Supply DC 3.7 V (Li-Ion Battery) Frequency Range 2 412 ~ 2 462 ㎒ (11b/g/n_HT20 Only) Modulation Technique DSSS, OFDM Number of Channels 11 Antenna Type Integral type (Chip Antenna ) Antenna Gain 3.96 dBi H/W version Ver 2.0 S/W version AMD120_020 1.4. Declaration by the manufacturer - 802.11n supports HT20 mode only - BT & WLAN cannot transmit simultaneously . Report Number: F690501/RF-RTL004915-1 Page: 4 of 46 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory)18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371www.kr.sgs.com/ee 1.5.Test Equipment List EQUIPMENTMANUFACTURERMODEL S/NCAL DUE. Signal Generator R & S SMR40 100272 Jul. 15, 2012 Spectrum Analyzer R & S FSV30 100768 Mar. 31, 2012 Spectrum Analyzer R & S FSP40 100007 Jul. 14, 2012 Preamplifier H.P 8447F 2944A03909 Jul. 04, 2012 Preamplifier R & S SCU 18 10117 Mar. 23, 2012 High Pass Filter Wainwright WHK3.0/18G-10SS344 Jul. 07, 2012 Power Sensor R & S NRP-Z81 100669 Apr. 04. 2012 Test Receiver R & S ESU26 100109 Feb. 21, 2012 Bilog Antenna SCHWARZBECK MESSELEKTRONIK VULB9163 396 Apr. 27, 2013 Horn Antenna R & S HF 906 100326 Oct. 08, 2011 Horn Antenna SCHWARZBECK BBH 9120D BBHA9170431 Mar. 17, 2012 Anechoic Chamber SY Corporation L × W × H (9.6 m×6.4 m×6.6 m) N.C.R. N.C.R. Two-Line V-Network R & S ENV216 100190 Jan. 04, 2012 Test Receiver R & S ESHS10 863365/018 Jul. 07, 2012 Anechoic Chamber SY Corporation L × W × H (6.5 m×3.5 m×3.5 m) N.C.R. N.C.R. Report Number: F690501/RF-RTL004915-1 Page: 5 of 46 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory)18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371www.kr.sgs.com/ee 1.6. Summary of Test Results The EUT has been tested according to the following specifications: APPLIED STANDARD:FCC Part15 subpart C Standard section Test Item Result 15.205(a) 15.209 15.247(d) Transmitter Radiated Spurious Emissions Conducted Spurious Emission Complied 15.247(a)(2) 6 ໒ Bandwidth Complied 15.247(b)(3) Maximum Peak Output Power Complied 15.247(e) Power Spectral Density Complied 15.207 Transmitter AC Power Line Conducted Emission Complied 1.7. Conclusion of worst-case The field strength of spurious emission was measured in three orthogonal EUT positions(X-axis, Y-axis and Z-axis). Worst case is X-axis. 11 Mbps is the highest output power in the 11b. 54 Mbps is the highest output power in the 11g. In case of 11n, we chose MCS7 mode. 1.8. Test report revision Revision Report number Description 0 F690501/RF-RTL004915 Initial 1 F690501/RF-RTL004915-1 Modified power value of 11b high Ch. (Low & Middle Ch: 18, High Ch: 17) Report Number: F690501/RF-RTL004915-1 Page: 6 of 46 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory)18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371www.kr.sgs.com/ee 2. Transmitter Radiated Spurious Emissions and Conducted Spurious Emission 2.1. Test Setup 2.1.1. Transmitter Radiated Spurious Emissions The diagram below shows the test setup that is utilized to make the measurements for emission from 30 ໬ to 1 ໭ Emissions. The diagram below shows the test setup that is utilized to make the measurements for emission from 1 ໭ to 24 ໭ Emissions. Report Number: F690501/RF-RTL004915-1 P…

Text truncated - open the document above for the full version.

Test Setup Photographs Body Back Body Top 5 mm Body Right EUT Photo Front Back Left Side Right Side

Test setup photos of EUT A. Photo of Field strength & Spurious Emission Test B. Photos of conducted power line test - BT - WLAN