P68UFO80802F88Remote Control Toy Transmitter

RC Flying Saucer Instruction Manual www.hover-copter.com Actual contents may vary slightly. Some assembly required Made in China HoverCopter is a trademark of Overbreak, LLC Sun Valley CA 91352 Conforms to ASTM F963 Keep this instruction manual as it contains important information. PRODUCT WARNINGS: 1. Caution: The HoverCopter is an electrically operated product. 2. Recommended for use by children eight years old and older. 3. As with all electric products, use caution during use and handling to prevent electric shock. 4. Keep your face, eyes, fingers, hair,and other body parts away from the propeller and gears. 5. Only fly the HoverCopter in a well-lit, uncrowded area where there is at least 10 feet of open space. 6. Do not expose the HoverCopter to water, rain, or moisture. 7. Do not fly the HoverCopter in total darkness. 8. Make sure people around you know you are flying the HoverCopter. 9. Do not fly the HoverCopter in crowded areas. 10. Do not fly the HoverCopter in dusty environments. 11. Be sure to turn the HoverCopter and Controller off when not in use. 12. Do not fly the HoverCopter near traffic. 13. Don not lift objects with the HoverCopter. 14. Do not use the HoverCopter if there is any damage to any f the components including the saucer, propeller, AC adaptor, its cord or plug, or Power docking station. AC ADAPTOR: The HoverCopter is intended for ages 8+. Keep this instruction manual-it contains important information. The HoverCopter operates only with the included AC adaptor. An adult should regularly examine and supervise the use of the AC adaptor. Do not use the HoverCopter if there is any damage to the power cord, plug, or other parts of the AC adaptor. Disconnect the AC adaptor before cleaning. The AC adaptor, power docking station and batteries may become warm during charging. AC adaptor should be disconnected from the HoverCopter when it is fully charged. Never leave the HoverCopter connected to the AC adaptor overnight. Do not overcharge the HoverCopter—this can damage the batteries. BATTERY SAFETY: Insert the batteries correctly as shown to prevent leakage. Batteries should be inserted and replaced by an adult. Batteries should not be exposed to direct sunlight, high heat, or fire—batteries may explode. Do not mix old and new batteries. Do not mix alkaline, non-alkaline, or rechargeable batteries. Do not try to recharge non-rechargeable batteries. If the HoverCopter will not be used for a long period, remove batteries to prevent leakage and damage. Remove dead batteries from Controller and power docking station. The batteries in the saucer are not replaceable. Be sure the battery compartments are screwed securely in place. Do not short circuit the battery terminals. Do not leave the HoverCopter connected to the AC adaptor overnight. Disconnect the AC adaptor from the HoverCopter when it is fully charged. Dispose of batteries properly, Do not throw them in the household garbage. Never dispose of batteries in fire- they may explode. In case of battery leaks, do not touch the leaking fluid. Place the leaking battery inside a plastic bag and dispose of properly. If leaking battery fluid touches your skin or eyes, wash with cool water for at least 15 minutes. BATTERY CARE: Fly the HoverCopter after each charge. Repeatedly charging without flying in between may damage the batteries or reduce their performance. CHARGING INDICATIN: The signal LED on the saucer will flash during charging. The signal LED will become dim and stop flashing after charging is completed.

PHOTOGRAPH OF THE PRODUCT FRONT VIEW OF THE PRODUCT REAR VIEW OF THE PRODUCT

FCC ID: P68UFO80802F88 MADE IN CHINA This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

PHOTOGRAPH OF THE PRODUCT INNER CIRCUIT TOP VIEW INNER CIRCUIT BOTTOM VIEW

1 RC FLYING SAUCER Circuit Description Model: HV-18 The 49.860MHz crystal oscillator drives the base of Q1 the high frequency amplifier. The modulated frequency provided by IC U1(PT8A977B). The output of Q2 has the matching network consisting of L2, L3, C7, C8, C9 and R11 that limit the harmonic content and effect the proper coupling of the antenna to the output stage. Antenna, Ground and Power Source The antenna consists of a 42.5cm long telescoping chrome over brass tubing. There is no external ground connection. The ground is only that of the printed circuit board. Electric current is supplied by 9V primary batteries.

香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-08-23 TEST REPORT Page 1 of 18 No. : HM152238 This report shall not be reproduced unless with prior written approval from the Hong Kong Standards and Testing Centre. 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). Applicant: Audex Telecom Industrial Co., Ltd. 1 st -4 th Floor, Xin Cun Kou, Qiwan Nan Road, Zhongshan, China Description of Samples: Model name: RC Flying Saucer Model no.: HV-18 Brand name: HoverCopter FCC ID: P68UFO080802F88 Date Samples Received: 2004-08-10 Date Tested: 2004-08-20 Investigation Requested: FCC Part 15 Subpart C Conclusions: The submitted product COMPLIED with the requirements of Federal Communications Commission [FCC] Rules and Regulations Part 15. The tests were performed in accordance with the standards described above and on Section 2.2 in this Test Report. Remarks: ---- K C Lee, EMC for Chief Executive 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-08-23 TEST REPORT Page 2 of 18 No. : HM152238 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). CONTENT: Cover Page 1 of 18 Content Page 2-3 of 18 1.0 General Details 1.1 Test Laboratory Page 4 of 18 1.2 Applicant Details Page 4 of 18 Applicant HKSTC Code Number for Applicant Manufacturer 1.3 Equipment Under Test [EUT] Page 5 of 18 Description of EUT operation 1.4 Date of Order Page 5 of 18 1.5 Submitted Samples Page 5 of 18 1.6 Test Duration Page 5 of 18 1.7 Country of Origin Page 5 of 18 1.8 Additional Information of EUT Page 6 of 18 2.0 Technical Details 2.1 Investigations Requested Page 7 of 18 2.2 Test Standards and Results Summary Page 7 of 18 3.0 Test Results 3.1 Emission Page 8-11 of 18 3.2 Bandwidth Measurement Page 12-13 of 18 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-08-23 TEST REPORT Page 3 of 18 No. : HM152238 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). Appendix A List of Measurement Equipment Page 14 of 18 Appendix B Photographs Page 15-18 of 18 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-08-23 TEST REPORT Page 4 of 18 No. : HM152238 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.0 General Details 1.1 Test Laboratory The Hong Kong Standards and Testing Centre Ltd. EMC Laboratory 10 Dai Wang Street, Taipo Industrial Estate New Territories, Hong Kong 1.2 Applicant Details Applicant Audex Telecom Industrial Co., Ltd. 1 st -4 th Floor, Xin Cun Kou, Qiwan Nan Road, Zhongshan, China HKSTC Code Number for Applicant AUT002 Manufacturer Audex Telecom Industrial Co., Ltd. 1 st -4 th Floor, Xin Cun Kou, Qiwan Nan Road, Zhongshan, China 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-08-23 TEST REPORT Page 5 of 18 No. : HM152238 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.3 Equipment Under Test [EUT] Description of Sample Model Name: RC Flying Saucer Manufacturer: Audex Telecom Industrial Co., Ltd. Brand Name: HoverCopter Model Number: HV-18 Input Voltage: 9Vd.c.(“6F22” size battery x1) 1.3.1 Description of EUT Operation The Equipment Under Test (EUT) is an Audex Telecom Industrial Co., Ltd., RC Flying Saucer. The transmitter is a 1 button transmitter. The EUT continues to transmit while button is being pressed, modulation by IC and type is pulse modulation. 1.4 Date of Order 2004-08-10 1.5 Submitted Sample(s): 1 Sample per model 1.6 Test Duration 2004-08-20 1.7 Country of Origin China 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-08-23 TEST REPORT Page 6 of 18 No. : HM152238 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.8 Additional Information of EUT Submitted Not Available User Manual Part List Circuit Diagram Printed Circuit Board [PCB] Layout Block diagram FCC ID Label 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-08-23 TEST REPORT Page 7 of 18 No. : HM152238 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 2.0 Technical Details 2.1 Investigations Requested Perform ElectroMagnetic Inter…

Text truncated - open the document above for the full version.

TEST SET UP PHOTOGRAPH OF THE PRODUCT MEASUREMENT OF RADIATED EMISSION TEST SET UP