PE3ISD-210900 MHz DSSS Digital Cordless Telephone

FCC RF Radiation Exposure Statement. Your cordless telephone contains a low-power transmitter. During use it sends out radio frequency (RF) signals. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. Caution: To maintain compliance with the FCC’s RF Exposure guidelines, hold the handset in such a manner as to maintain a separation distance of 0.5 inches (1.25 cm) between the antenna and your body with the antenna pointed up and away from your head. If you wear the handset on your body while using a headset accessory, use only the manufacturer’s supplied belt clip for this product and ensure that the antenna is at least 1 inch (2.5 cm) from your body during use. Important Note: Use only the supplied antenna. Unauthorized antennas, modifications, or attachments could damage the transmitter and may violate FCC regulations.

APPLICANT: ISV CO., LTD. FCC ID: PE3ISD-210 TABLE OF CONTENTS TEST REPORT CONTAINING: PAGE 1-2..........TEST PROCEDURE & EQUIPMENT LIST PAGE 3............PRODUCT DESCRIPTION, SPREAD SPECTRUM BIT RATES AND SECURITY CODING INFORMATION PAGE 4............POWER LINE CONDUCTED EMISSIONS PAGE 5A-5B........POWER LINE CONDUCTED PLOTS PAGE 6............6dB BANDWIDTH PAGE 7A-7D........OCCUPIED BANDWIDTH PLOTS PAGE 8............POWER OUTPUT PAGE 9............METHOD OF MEASURING RF CONDUCTED EMISSIONS PAGE 10-11........SPURIOUS EMISSIONS AT ANTENNA TERMINALS PAGE 12-13........FIELD STRENGTH OF SPURIOUS EMISSIONS PAGE 14...........METHOD OF MEASURING SPURIOUS EMISSIONS PAGE 15...........POWER SPECTRAL DENSITY PAGE 16A-16F......POWER SPECTRAL DENSITY PLOTS PAGE 17...........PROCESSING GAIN PAGE 18A-18D......PROCESSING GAIN DATA EXHIBIT ATTACHMENTS: EXHIBIT 1..........FCC ID LABEL SAMPLE EXHIBIT 2..........SKETCH OF FCC ID LABEL LOCATION EXHIBIT 3A-3B......BLOCK DIAGRAM EXHIBIT 4A.........SCHEMATIC - TX/RX - RF EXHIBIT 4B.........SCHEMATIC - HAND KEY EXHIBIT 4C.........SCHEMATIC - BASE EXHIBIT 4D.........SCHEMATIC EXHIBIT 5A-5B......RADIATED TEST SETUP PHOTOGRAPH EXHIBIT 5C.........POWERLINE SETUP PHOTOGRAPH EXHIBIT 6A.........EXTERNAL PHOTOGRAPH - HANDSET - FRONT VIEW EXHIBIT 6B.........EXTERNAL PHOTOGRAPH - BASE - FRONT VIEW EXHIBIT 6C.........EXTERNAL PHOTOGRAPH - HANDSET - REAR VIEW EXHIBIT 6D.........EXTERNAL PHOTOGRAPH - BASE - REAR VIEW EXHIBIT 7A.........INTERNAL PHOTOGRAPH - HANDSET - COMPONENT VIEW EXHIBIT 7B.........INTERNAL PHOTOGRAPH - BASE - COMPONENT VIEW EXHIBIT 7C.........INTERNAL PHOTOGRAPH - HANDSET - COPPER VIEW EXHIBIT 7D.........INTERNAL PHOTOGRAPH - BASE - COPPER VIEW EXHIBIT 8A-8X......USERS'S MANUAL EXHIBIT 9..........RF EXPOSURE STATEMENT FOR USER'S MANUAL EXHIBIT 10A-10B...CIRCUIT DESCRIPTION APPLICANT: ISV CO., LTD. FCC ID: PE3ISD-210 REPORT #: T:\cus\I\ISV\594U0\594U0RPT.doc PAGE #: TABLE OF CONTENTS APPLICANT: ISV CO., LTD. FCC ID : PE3ISD-210 TEST EQUIPMENT LIST 1._X_Spectrum Analyzer: HP 8566B-Opt 462, S/N 3138A07786, w/ preselector HP 85685A, S/N 3221A01400, Quasi-Peak Adapter HP 8565OA, S/N 3303A01690 & Preamplifier HP 8449B-OPT H02, S/N 3008A00372 Cal. 10/17/99 2._X_Biconnical Antenna: Eaton Model 94455-1, S/N 1057 3.___Biconnical Antenna: Electro-Metrics Model BIA-25, S/N 1171 4._X_Log-Periodic Antenna: Electro-Metrics Model EM-6950, S/N 632 5.___Log-Periodic Antenna: Electro-Metrics Model LPA-30, S/N 409 6.___Double-Ridged Horn Antenna: Electro-Metrics Model RGA-180, 1-18 GHz, S/N 2319 7.___18-26.3GHz Systron Donner Standard Gain Horn #DBE-520-20 8.___Horn 40-60GHz: ATM Part #19-443-6R 9.___Line Impedance Stabilization Network: Electro-Metrics Model ANS-25/2, S/N 2604 Cal. 2/9/00 10.___Temperature Chamber: Tenney Engineering Model TTRC, S/N 11717-7 11.___Frequency Counter: HP Model 5385A, S/N 3242A07460 Cal 10/6/99 12.___Peak Power Meter: HP Model 8900C, S/N 2131A00545 13._X_Open Area Test Site #1-3meters Cal. 12/22/99 14.___Signal Generator: HP 8640B, S/N 2308A21464 Cal. 9/23/99 15.___Signal Generator: HP 8614A, S/N 2015A07428 16.___Passive Loop Antenna: EMCO Model 6512, 9KHz to 30MHz, S/N 9706-1211 Cal. 6/10/00 17.___Dipole Antenna Kit: Electro-Metrics Model TDA-30/1-4, S/N 153 Cal. 11/24/99 18.___AC Voltmeter: HP Model 400FL, S/N 2213A14499 Cal. 9/21/99 19.___Digital Multimeter: Fluke Model 8012A, S/N 4810047 Cal 9/21/99 20.___Digital Multimeter: Fluke Model 77, S/N 43850817 Cal 9/21/99 21.___Oscilloscope: Tektronix Model 2230, S/N 300572 Cal 9/23/99 TEST PROCEDURE GENERAL: This report shall NOT be reproduced except in full without the written approval of TIMCO ENGINEERING, INC. Shielded interface cables were used in all cases except for cables connecting to the telephone line and the power cords. A test program was run which simulated a normal data transmission on a network. POWER LINE CONDUCTED INTERFERENCE: The procedure used was ANSI STAN- DARD C63.4-1992 using a 50uH LISN. Both lines were observed with the UUT transmitting. The bandwidth of the spectrum analyzer was 10kHz with an appropriate sweep speed. The ambient temperature of the UUT was 59oF with a humidity of 45%. APPLICANT: ISV CO., LTD. FCC ID: PE3ISD-210 REPORT #: T:\cus\I\ISV\594U0\594U0RPT.doc PAGE #: 1 APPLICANT: ISV CO., LTD. FCC ID: PE3ISD-210 TEST PROCEDURES CONTINUED BANDWIDTH 6.0dB: The measurements were made withe the spectrum analyz- er's resolution bandwidth(RBW)=1.0MHz and the video bandwidth(VBW) =3.0MHz and the span set as shown on plot. POWER OUTPUT: The RF power output was measured at the antenna feed point using a peak power meter. ANTENNA CONDUCTED EMISSIONS: The RBW=100KHz, VBW=300KHz and the span set to 10.0MHz and the spectrum was scanned from 30MHz to the 10th Harmonic of the fundamental. Above 1.0GHz the resolution bandwidth was 1.0MHz and the VBW = 3.0MHz and the span to 50MHz. RADIATION INTERFERENCE: The test procedure used was ANSI STANDARD C63.4-1992 using a HEWLETT PACKARD spectrum analyzer with a prese- lector. The bandwidth(RBW) of the spectrum analyzer was 100kHz up to 1GHz and 1.0MHz above 1GHz with an appropriate sweep speed. The VBW above 1.0GHz was = 3.0MHz. The analyzer was calibrated in dB above a microvolt at the output of the antenna. The ambient temperature of the UUT was 59oF with a humidity of 45%. APPLICANT: ISV CO., LTD. FCC ID: PE3ISD-210 REPORT #: T:\cus\I\ISV\594U0\594U0RPT.doc PAGE #: 2 APPLICANT: ISV CO., LTD. FCC ID: PE3ISD-210 PRODUCT DESCRIPTION: The PE3ISD-210 is a direct sequence spread spectrum cordless telephone that operates in the 904-928 MHz band. The antenna used for the base and the handset is permenantly attached to the UUT. Its actual fre- quency range is; CHANNEL 1 904.00MHz Lowest CHANNEL 20 928.00MHz Highest THE FOLLOWING SPREAD SPECTRUM INFORMATION WAS PROVIDED BY THE MANUFAC- TURER: The Chipping Rate is: 12 chips/bit The Bit Rate is: 1.92Mbps The Data Rate is: 800Kbps Time Division Duplex The Spreading Rate is: 12 chips/bit * 100Kbi…

Text truncated - open the document above for the full version.

]