PNXLT-033USB Rechargeable speaker lantern

LED Bluetooth Lantern OPERATION INSTRUCTION MANUAL READ ALL INSTRUCTIONS BEFORE FIRST USE KEEP THIS MANUAL FOR REFERENCE. Before rst and every use, charge the unit battery fully following the instructions on “HOW TO CHARGE”. When the battery is not in use for a long period, the runtime of the light will be shortened due to the self-discharge of the battery. Before First Use Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 1 2 3 Product Features The lantern had a function of High, Low, Red lights and O Integrated wireless Bluetooth speaker connection, Bluetooth 3.0 Audio Bluetooth On / O power switch Built in 3.7V 1600mAh Lithium Battery DC5V USB output, suitable for battery charge on electronic devices with USB input. Connect audio cable (not included) directly to AUX audio plug to play music without Bluetooth connection. Intergraded handle with hook Main Button Battery Power Indicator (BPI) USB cover Micro-USB Charger Port USB Output Bluetooth “On / O ” Switch Speaker AUX audio plug Micro USB charging cable 1 2 3 4 5 6 7 8 9 10 8 CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Model : LT-033 5 6 7 9 4 10 Specication Illumination 4 - 5 hrs (High) 10 - 12 hrs 110 - 120 Lumens 40 - 50 hrs (Low) 30 - 40 hrs (Red) Runtime 3.7V 1600mAh Lithium battery Battery Type -20 ̊c to 45 ̊c Operating Temperature ≤ 90% Operating Humidity Bluetooth Speaker Runtime Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different fromthat to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IMPORTANT! WARNING! DO NOT immerse in water, drop into fire. DO NOT disassembly the product. Please charging the lantern at least once per 1 months in order to keep the battery in normal stage. Please always handle the battery in safety way. If the lantern has been destroyed or crashed, do not use it again or consult your product provider The USB charging cable is for indoor use only. Never short-circuit the terminal of the battery and the plug of the USB charging cable. It may cause the battery to overheat, resulting in fire or damage of the components. If the USB charging cable, USB plug, or lantern body is damaged. DO NOT use it. Use only the Micro USB charging cable for charging. Lithium batteries in the product can easily rupture, ignite, or explode when exposed to high temperatures, or direct sunlight. The product should be stored and charged under well ventilated environment. Short-circuiting a battery can also cause it to ignite or explode. Never open a battery's casing. Batteries contain safety devices that, protect the cells inside from abuse. If damaged, these can cause the battery to ignite or exploded DO NOT charge the lantern and charge an electronic device at the same time. This will shorten the lantern’s battery life. Securely close the USB cover at the back of the lantern so that it will not be damage while water splash/ rain, or the water resistance will be compromise. Safely and properly dispose of the battery lantern according to your local regulations when it comes to the end of its useful life. This lantern is NOT a toy. Children should be supervised to ensure that they do not play with this lantern. A long period of non-use will lower the voltage of the battery due to natural self-discharge. If the light is kept on until the power is completely gone (i.e. over discharge), it may shorten the battery life. Even when you do not use the lantern. Charge the battery every month. DO NOT charge the lantern for more than 8 hours. If the lantern does not serve the proper running time even though the battery is fully charged, the battery may have reached the end of its useful life. 06012015 V1 Fully charge the lantern use only the Micr…

Text truncated - open the document above for the full version.

1 Photographs - EUT Constructional Details Test model No.: LT-033

For European Market (EEC market) For US Market: FCC Wording “Made in China” CE logo, WEEE logo, model No. and Company trade mark Model number: LT-033 Company trademark

1 Photographs - EUT Constructional Details Test model No.: LT-033

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM141200714603 Page: 1 of 7 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No: SZEM1412007146CR Applicant/ Manufacturer: Flying Dragon Development Ltd Factory: Atoz Electronic Technology Co., Ltd Product Name: USB Rechargeable speaker lantern Model No.(EUT): LT-033 FCC ID: PNXLT-033 Standards: 47 CFR Part 1.1307 (2014) 47 CFR Part 2.1093 (2014) KDB447498D01 General RF Exposure Guidance v05 Date of Receipt: 2014-12-30 Date of Test: 2015-01-04 Date of Issue: 2015-01-16 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM141200714603 Page: 2 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-01-16 Original Authorized for issue by: Tested By 2015-01-04 (Eric Fu) /Project Engineer Date Prepared By 2015-01-16 (Linlin Lv) /Clerk Date Checked By 2015-01-21 (Kevin Feng) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM141200714603 Page: 3 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE ...................................................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM141200714602 Page: 1 of 99 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1412007146CR Applicant/ Manufacturer: Flying Dragon Development Ltd Factory: Atoz Electronic Technology Co., Ltd Product Name: USB Rechargeable speaker lantern Model No.(EUT): LT-033 FCC ID: PNXLT-033 Standards: 47 CFR Part 15, Subpart C (2014) Date of Receipt: 2014-12-30 Date of Test: 2015-01-04 Date of Issue: 2015-01-16 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM141200714602 Page: 2 of 99 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-01-16 Original Authorized for issue by: Tested By 2015-01-04 (Eric Fu) /Project Engineer Date Prepared By 2015-01-16 (Linlin Lv) /Clerk Date Checked By 2015-01-21 (Kevin Feng) /Reviewer Date SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM141200714602 Page: 3 of 99 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 (2009) PASS AC Power Line Conducted Emission 47 CFR Part 15, Subpart C …

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup Test model No.: LT-033 1.1 Conducted Emission 1.2 Radiated Emission 1.3 Radiated Spurious Emission