PODTH-UVF9Two-way Radio

SAFETYTRAINING INFORMATION Yo u r TYT ELECTRONICS CO.,LTD radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only”. In addition, your TYT ELECTRONICS CO.,LTD radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:  FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.  American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.  American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave.  The following accessories are authorized for use with this product. Use of accessories other than those (listed in the instruction) specified may result in RF exposure levels exceed the FCC requirements for wireless RF exposure. To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines:  DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio.  DO NOT transmits for more than 50% of total radio use time (“50%duty cycle”). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “TX indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch.  ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the HYT belt-clip which is listed in instructions when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. T he information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as‐sure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your TYT ELECTRONICS CO.,LTD radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure.

March 27, 2013 Federal Communication Commission Authorization and Evaluation Division FCC ID: PODTH-UVF9 Re: Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the applicant hereby requests confidential treatment of information applied this application as outlined below: 1: Block Diagram 2: Circuit Diagram 3: Operational Description 4: Parts List 5:Tune Up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rules 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, TYT ELECTRONICS CO.,LTD Jiamao Lin /Manager

March 27, 2013 Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Colombia, Maryland 21046 Subject: FCC ID: PODTH‐UVF9 Justification Letter for Expanded Frequency Range 400‐470 MHz Gentlemen; You have asked TYT ELECTRONICS CO.,LTD for justification to have the freq range 400‐470 MHz appears on the face of the FCC Grant of Certification for a Part 90 Certification. This frequency range is regarded as usual & customary by United States Federal Government and its various departments, user organizations and the military to appear on the face of the equipment Grant of Certification. (1) TYT ELECTRONICS CO.,LTD’s Marketing Department plans to ensure that USA users, other than those specifically identified in this letter, not operate within bands 400‐406 MHz, as controlled by the users’ FCC station license. (2) This device will not be marketed to USA users, other than those identified in the letter, namely the US Government and its various departments & military, for operation in 400‐406 MHz frequency range. Sincerely, TYT ELECTRONICS CO.,LTD Jiamao Lin /Manager

TYT ELECTRONICS CO., LT D Block 39-1,Optoelectronics information industry base,Nan’an, quanzhou,Fujian,China Tel: 0595‐86766928; FAX: 0595‐86767928 Date: Sep.27,2012 Statement We, TYT ELECTRONICS CO., LTD states that our device, FCC ID: PODTH‐UVF9, has no space to put the label except the battery compartment of this device. It is visible to the users as they purchase the products and install the battery. Sincerely, TYT ELECTRONICS CO.,LTD Jiamao Lin /Manager

TOTAL VIEW OF EUT TOP VIEW OF EUT BOTTOM VIEW OF EUT FRONT VIEW OF EUT BACK VIEW OF EUT LEFT VIEW OF EUT RIGHT VIEW OF EUT

FCC ID Label Location FCC RF Warning Label Two-way radio Brand : TYT FCC ID: PODTH‐UVF9 Model : TH‐UVF9,TH‐UVF10,YH‐UV11,TH‐UV12 Fre quency Range: 136-174MHz，400-470MHz

OPEN VIEW OF EUT INTERNAL VIEW OF EUT - 1 INTERNAL VIEW OF EUT - 2

Report No.: AGC092120801-2S1 Page 1 of 86 SAR Test Report Report No.: AGC092120801-2S1 FCC ID : PODTH-UVF9 Product Designation : Two-way Radio Brand Name : TYT Model Name : TH-UVF9,TH-UVF10,TH-UV11,TH-UV12 Client : TYT ELECTRONICS CO.,LTD Date of Issue : Mar.26, 2013 STANDARD(S) : FCC Oet65 Supplement C June 2001 IEEE Std. 1528-2003,47CFR § 2.1093 Attestation of Global Compliance (Shenzhen) Co., Ltd. CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context. Report No.: AGC092120801-2S1 Page 2 of 86 Test Report Certification Applicant Name : TYT ELECTRONICS CO.,LTD Applicant Address : Block 39-1,Optoelectronics information industry base,Nan’an,quanzhou,Fujian Manufacturer Name : TYT ELECTRONICS CO.,LTD Manufacturer Address : Block 39-1,Optoelectronics information industry base,Nan’an,quanzhou,Fujian Product Name : Two-way Radio Brand Name : TYT Model Name : TH-UVF9,TH-UVF10,TH-UV11,TH-UV12 Difference Description They have the same PCB Board, Just difference with its appearance EUT Voltage : DC7.4V by battery Applicable Standard : FCC Oet65 Supplement C June 2001 IEEE Std. 1528-2003,47CFR § 2.1093 Test Date : Mar.25, 2013 Test Results : MAX SAR MEASUREMENT(1g) with 50% duty cycle V: Head: 1.031 W/Kg Body: 2.064 W/Kg (Scaling SAR=2.095 W/Kg) U: Head: 3.841 W/Kg Body: 4.091 W/Kg （Scaling SAR=4.118 W/Kg) Performed Location : Attestation of Global Compliance (Shenzhen)Co., Ltd. 2F, Building 2, No.1-No.4, Chaxi Sanwei Technical Industrial Park, Gushu, Xixiang Street, Bao'an District, Shenzhen, China Documented By Vivi Zeng Mar.26, 2013 Checked By Angela Li Mar.26, 2013 Authorized By Solger Zhang Mar.26, 2013 Report No.: AGC092120801-2S1 Page 3 of 86 TABLE OF CONTENTS 1. GENERAL INFORMATION .............................................................................................................................. 4 1.1. EUT Description ....................................................................................................................................... 4 1.2. Test Procedure ......................................................................................................................................... 5 1.3. Test Environment ..................................................................................................................................... 5 2. SAR MEASUREMENT SYSTEM........................................................................................................................ 6 2.1. COMOSAR System Description ............................................................................................................... 6 2.3 Robot ........................................................................................................................................................ 8 2.4. Video Positioning System ......................................................................................................................... 9 2.5. Device Holder .......................................................................................................................................... 9 2.6. Elliptic Phantom ..................................................................................................................................... 10 3. TISSUE SIMULATING LIQUID ....................................................................................................................... 11 3.1. The composition of the tissue simulating liquid ....................................................................................... 11 3.2. Tissue Calibration Result ........................................................................................................................ 12 3.3. Tissue Dielectric Parameters for Head and Body Phantoms .................................................................. 13 4. SAR MEASUREMENT PROCEDURE ............................................................................................................ 14 4.1. SAR System Validation .......................................................................................................................... 14 4.2. SAR Measurement Procedure ............................................................................................................... 16 5. SAR EXPOSURE LIMITS ............................................................................................................................... 17 6. TEST EQUIPMENT LIST ................................................................................................................................ 18 7. MEASUREMENT UNCERTAINTY .................................................................................................................. 19 8. CONDUCTED POWER MEASUREMENT....................................................................................................... 20 9. TEST RESULTS ............................................................................................................................................. 21 APPENDIX A. SAR SYSTEM VALIDATION DATA ............................................................................................ 24 APPENDIX B. SAR MEASUREMENT DATA ...................................................................................................... 28 APPENDIX C. TEST SETUP PHOTOGRAPHS &EUT PHOTOGRAPHS .......................................................... 52 APPENDIX D. PROBE CALIBRATION DATA ................................................................................................... 59 APPENDIX E. DIPOLE CALIBRATION DATA ................................................................................................... 69 Report No.: AGC092120801-2S1 Page 4 of 86 1. General Information 1.1. EUT Description Product Name Two-way Radio Test Model TH-UVF9 Hardware Version F9 v2.0 Software Version F9 v2.0 Exposure Category: Occupational/Co…

Text truncated - open the document above for the full version.

Report No.: AGC092120801-2S1 Page 52 of 86 Appendix C. TEST SETUP PHOTOGRAPHS &EUT PHOTOGRAPHS Test Setup Photographs Face Up with 2.5 cm Separation Distance. Body Back Touch with all accessories 2.5cm Report No.: AGC092120801-2S1 Page 53 of 86 EUT PHOTOGRAPHS TOTAL VIEW OF EUT TOP VIEW OF EUT Report No.: AGC092120801-2S1 Page 54 of 86 BOTTOM VIEW OF EUT FRONT VIEW OF EUT Report No.: AGC092120801-2S1 Page 55 of 86 BACK VIEW OF EUT LEFT VIEW OF EUT Report No.: AGC092120801-2S1 Page 56 of 86 RIGHT VIEW OF EUT OPEN VIEW OF EUT-1 Report No.: AGC092120801-2S1 Page 57 of 86 OPEN VIEW OF EUT-2 OPEN VIEW OF EUT-3 Report No.: AGC092120801-2S1 Page 58 of 86 INTERNAL VIEW OF EUT – 1 INTERNAL VIEW OF EUT – 2 Report No.: AGC092120801-2S1 Page 59 of 86 Appendix D. Probe Calibration Data Report No.: AGC092120801-2S1 Page 60 of 86 Report No.: AGC092120801-2S1 Page 61 of 86 Report No.: AGC092120801-2S1 Page 62 of 86 Report No.: AGC092120801-2S1 Page 63 of 86 Report No.: AGC092120801-2S1 Page 64 of 86 Report No.: AGC092120801-2S1 Page 65 of 86 Report No.: AGC092120801-2S1 Page 66 of 86 Report No.: AGC092120801-2S1 Page 67 of 86 Report No.: AGC092120801-2S1 Page 68 of 86 Report No.: AGC092120801-2S1 Page 69 of 86 Appendix E. Dipole Calibration Data Report No.: AGC092120801-2S1 Page 70 of 86 Report No.: AGC092120801-2S1 Page 71 of 86 Report No.: AGC092120801-2S1 Page 72 of 86 Report No.: AGC092120801-2S1 Page 73 of 86 Report No.: AGC092120801-2S1 Page 74 of 86 Report No.: AGC092120801-2S1 Page 75 of 86 Report No.: AGC092120801-2S1 Page 76 of 86 Report No.: AGC092120801-2S1 Page 77 of 86 Report No.: AGC092120801-2S1 Page 78 of 86 Report No.: AGC092120801-2S1 Page 79 of 86 Report No.: AGC092120801-2S1 Page 80 of 86 Report No.: AGC092120801-2S1 Page 81 of 86 Report No.: AGC092120801-2S1 Page 82 of 86 Report No.: AGC092120801-2S1 Page 83 of 86 Report No.: AGC092120801-2S1 Page 84 of 86 Report No.: AGC092120801-2S1 Page 85 of 86 Report No.: AGC092120801-2S1 Page 86 of 86

FCC Part 90 Test Report Report No.: AGC092120801-2F2 TEST NAME : FCC Part 90 APPLICATION PURPOSE : Original Equipment FCC ID : PODTH-UVF9 PRODUCT DESIGNATION : Two-way Radio BRAND NAME : TYT MODEL NAME : TH-UVF9,TH-UVF10,TH-UV11,TH-UV12 CLIENT : TYT ELECTRONICS CO.,LTD DATE OF ISSUE : Mar. 27, 2013 STANDARD(S) : FCC Part 90 Rules Attestation of Global Compliance (Shenzhen) Co., Ltd. CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context. Report No.: AGC092120801-2F2 Page 1 of 63 VERIFICATION OF COMPLIANCE Applicant: TYT ELECTRONICS CO.,LTD Block 39-1,Optoelectronics information industry base,Nan’an,quanzhou,Fujian Manufacturer: TYT ELECTRONICS CO.,LTD Block 39-1,Optoelectronics information industry base,Nan’an,quanzhou,Fujian Product Description: Two-way Radio Brand Name: TYT Model Name: TH-UVF9,TH-UVF10,TH-UV11,TH-UV12 Model Difference: All the same except for appearance and test model is TH-UVF9. File Number: AGC092120801-2F2 Date of Test: Mar.19,2013 to Mar.22,2013 We hereby certify that: The above equipment was tested by Attestation of Global Compliance (Shenzhen) Co., Ltd. The data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C 63.4:2003 and TIA/EIA 603. The sample tested as described in this report is in compliance with the FCC Rules Part 90 requirements. The test results of this report relate only to the tested sample identified in this report. Tested By Bart Xie Mar. 27, 2013 Reviewed By Forrest Lei Mar. 27, 2013 Approved By Solger Zhang Mar. 27, 2013 Report No.: AGC092120801-2F2 Page 2 of 63 TABLE OF CONTENTS 1. GENERAL INFORMATION ............................................................................................. 4 1.1 PRODUCT DESCRIPTION ..................................................................................................................... 4 1.3 TEST METHODOLOGY ......................................................................................................................... 5 1.4 TEST FACILITY ...................................................................................................................................... 5 1.5 SPECIAL ACCESSORIES ..................................................................................................................... 5 1.6 EQUIPMENT MODIFICATIONS ............................................................................................................. 5 2. SYSTEM TEST CONFIGURATION ................................................................................ 6 2.1 EUT CONFIGURATION .......................................................................................................................... 6 2.2 EUT EXERCISE ..................................................................................................................................... 6 2.3 GENERAL TECHNICAL REQUIREMENTS ........................................................................................... 6 2.4 CONFIGURATION OF TESTED SYSTEM ........................................................................................... 6 3. SUMMARY OF TEST RESULTS .................................................................................... 7 4. DESCRIPTION OF TEST MODES.................................................................................. 8 5. CONDUCTED LIMITS .................................................................................................... 9 5.1 PROVISIONS APPLICABLE .................................................................................................................. 9 5.2 MEASUREMENT PROCEDURE ............................................................................................................ 9 5.3 TEST SETUP BLOCK DIAGRAM ........................................................................................................ 10 5.4 TEST EQUIPMENT USED ................................................................................................................... 10 5.5 TEST RESULT ...................................................................................................................................... 11 6. FREQUENCY TOLERANCE ........................................................................................ 13 6.1 PROVISIONS APPLICABLE ................................................................................................................ 13 6.2 MEASUREMENT PROCEDURE .......................................................................................................... 13 6.3 TEST SETUP BLOCK DIAGRAM ........................................................................................................ 14 6.4 TEST EQUIPMENT USED: .................................................................................................................. 14 6.5 TEST RESULT ...................................................................................................................................... 14 7. EMISSION BANDWIDTH ............................................................................................. 19 7.1 PROVISIONS APPLICABLE ................................................................................................................ 21 7.2 MEASUREMENT PROCEDURE .......................................................................................................... 21 7.3 TEST SETUP BLOCK DIAGRAM ........................................................................................................ 21 7.4 MEASUREMENT EQUIPMENT USED: ............................................................................................... 21 7.5 MEASUREMENT RESULT: .................................................................................................................. 22 8. UNWANTED RADIATION .............................…

Text truncated - open the document above for the full version.

CONDUCTED EMISSION TEST SETUP RADIATED TEST SETUP