POZCPEWCS005239BSOMAport Subscriber wireless terminal

1 Contents March 28, 2006 Part 004840A Rev 03 Introduction............................................................................ 9 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 The Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 The Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 The Internal Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Installing the SOMAport...................................................... 15 Unpack the SOMAport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Choose the Best Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Power on the SOMAport. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Connect Computer Using Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . .19 Connect Computer Using USB. . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Connect Telephones to the SOMAport. . . . . . . . . . . . . . . . . . . . . . .22 Activate Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Connecting Multiple Computers ........................................ 27 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Using an Ethernet Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Using an Internet Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Troubleshooting .................................................................. 31 Finding Causes of Computer Problems . . . . . . . . . . . . . . . . . . . . . .32 Finding Causes of Telephone Problems . . . . . . . . . . . . . . . . . . . . .33 The Signal is Weak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 There is a Fault Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 The SOMAport is Not Receiving Power . . . . . . . . . . . . . . . . . . . . . .36 There is a Problem with the Ethernet or USB Cabling . . . . . . . . . . .37 There is a Problem with the USB Port Settings . . . . . . . . . . . . . . . .39 sp3.book Page 1 Tuesday, March 28, 2006 5:09 PM 2 The Computer Uses an Old Dial-Up Connection . . . . . . . . . . . . . . 40 Internet Explorer LAN Settings are Incorrect . . . . . . . . . . . . . . . . . 42 Ethernet Network Settings are Incorrect . . . . . . . . . . . . . . . . . . . . . 43 IP address Needs to be Renewed . . . . . . . . . . . . . . . . . . . . . . . . . 52 Specifications ......................................................................55 Index .....................................................................................57 sp3.book Page 2 Tuesday, March 28, 2006 5:09 PM 3 SOMA NETWORKS INC. ENDUSER PRODUCT LICENSE AGREEMENT THE SOMAPORT™ SUBSCRIBER TERMINAL AND PROVIDED SOFTWARE CONTAIN CERTAIN COMPUTER PROGRAMS AND OTHER PROPRIETARY MATERIAL OF SOMA NETWORKS INC. OR LICENSED TO SOMA NETWORKS, INC., THE USE OF WHICH IS SUBJECT TO THIS AGREEMENT. BY: (A) SIGNING AN AGREEMENT FOR SERVICE WITH YOUR SERVICE PROVIDER; (B) OPENING THE SEALED ENVELOPE CONTAINING THE SOMAPORT; OR (C) USING THE SOMAPORT, YOU ASSENT TO AND ACCEPT THIS ENDUSER PRODUCT LICENSE AGREEMENT. IF YOU DO NOT AGREE WITH ALL THE TERMS OF THIS AGREEMENT YOU MUST RETURN THIS PRODUCT (WITH THE ENVELOPE STILL SEALED), ALL MANUALS AND DOCUMENTATION, ANY SOFTWARE PACKAGES PROVIDED WITH THE SOMAPORT AND PROOF OF PAYMENT TO THE PLACE YOU OBTAINED THEM FOR A FULL REFUND WITHIN THIRTY (30) DAYS OF FIRST ACQUIRING THE SOMAPORT, OTHERWISE YOU ARE DEEMED TO HAVE ACCEPTED AND AGREED TO THESE TERMS AND CONDITIONS. UNAUTHORIZED REPRODUCTION, DISTRIBUTION, DECOMPILATION OR OTHER REVERSE ENGINEERING OF THIS PRODUCT INCLUDING ITS HARDWARE AND/OR SOFTWARE, OR ANY PORTION OF IT, IS PROHIBITED AND MAY RESULT IN SEVERE CIVIL AND CRIMINAL PENALTIES, AND WILL BE PROSECUTED TO THE MAXIMUM EXTENT POSSIBLE UNDER THE LAW. 1. GRANT OF LICENSE: Subject to the terms of this Enduser Product License Agreement (the “Agreement”), SOMA Networks, Inc. (“SOMA”) grants you (the “Licensee”) a non-sub-licensable, non-exclusive right (“License”) to use the Product. “Product” means, collectively, the Software and the provided hardware, and specifically the SOMAport™ subscriber terminal and its accessories, if any, together with documentation provided to you by SOMA or your service provider. “Software” means, collectively, the version of the SOMA software program in object code format and all updates to that program distributed to you by SOMA, directly or indirectly, by any means and includes any firmware provided to you with the Product. You have no right, unless otherwise explicitly permitted, to receive any source code or design documentation relating to the Product. SOMA retains ownership of all Software copies. The Software and this License is only provided to you to be used in conjunction with the SOMAport provided to you by SOMA or your service provider when you subscribed to services that utilize the SOMA wireless air interface technology and is not licensed to you to be used for any other purpose. 2. RESTRICTIONS: Except as reasonably required to use the Product strictly in accordance with the License and this Agreement, you may not copy any Software. Licensee shall not (and shall not allow any third party to): (I) decompile, disassemble, or otherwise reverse engineer or attempt to reconstruct or discover any source code or underlying ideas or algorithms or file formats or programming or interoperability interfaces of the Product by any means whatsoever; (II) remove any Product identification, copyright or other notices; (III) modify, incorporate into or with other software or create a derivative work of any part of the Software or Product; or (IV) modify or otherwise alter the operation of the Produc…

Text truncated - open the document above for the full version.

SOMA Networks, Inc. 185 Berry Street, Suite 4600 ◦ San Francisco, California 94107 March 8, 2006 ATTN:Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: LETTER OF AGENT AUTHORIZATION, FCC ID: POZCPEPCS005239B To Whom It May Concern: We, the undersigned, hereby authorize MET Laboratories, Inc. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Robin Grindley Chief Scientist – Hardware Systems SOMA Networks, Inc. 185 Berry St. Ste. 4600, SF, CA, 94107 185 Berry Street • Suite 4600 • San Francisco CA 94107 • Phone: 415.882.6500 • Fax: 415.882.6512

MET TCB SERVICE AGREEMENT DOCJ-TCB002 11/24/04 Page of 3 THIS AGREEMENT is made at Baltimore, Maryland this 6 th day of April, 2006, by and between MET LABORATORIES, INC. (hereinafter referred to as MET) and the following: Applicant: SOMA Networks, Inc. (Hereinafter referred to as the "Responsible Party") Address: 185 Berry Street, Suite 4600 San Francisco, CA, 94107 Only the product(s) designed and engineered by the Applicant/Responsible Party and manufactured by the Manufacturer at the Manufacturer's facility at the above address, which have been certified by MET are covered by this service Agreement. NOW, THEREFORE, in consideration of the premises set forth in this agreement, the above mentioned parties agree that; Upon successful evaluation, MET will issue the Applicant/Responsible Party a Grant of Equipment Authorization Certificate, granting the Applicant/Responsible Party permission to market the certified product(s). At a minimum the product's identification plate or label will include the FCC ID Number or the Registration/Certification Number as well as any other information as might be required bystatute. The FCC requires that MET perform random post-certification surveillance. Surveillance for continued certification compliance can be accomplished by the Applicant/Responsible Party providing production models of the product to MET at MET’s request or to other locations as approved by MET for the purpose of compliance testing. The Manufacturer agrees to allow free and unrestricted access to the Manufacturer's facility during normal working hours for the purpose of permitting supervision. The Applicant/Responsible Party or Manufacturer agrees to provide and deliver to MET or locations approved by MET models of the certified product at MET’s request. All costs associated with testing of the device will be borne by the Applicant/Responsible Party or the Manufacturer and paid within 30 days of notice. If required the Applicant/Responsible Party agrees to provide to MET for MET review certain identified technical documents or quality documents that provide for a review of product update and compliance. Acceptable Markings are found in 47 CFR 2.925, 2.926, 15.19, and part 68.300. Only products visually bearing the appropriate FCC identification label and identified as to model and type will be acknowledged as being an authorized product. The Applicant/Responsible Party is responsible for applying the label to the product in accordance with current FCC requirements. An Applicant/Responsible Party is required to submit to MET a sample of the label or plate showing the FCC ID Number or the Registration/Certification Number for approval prior to applying to the product. The Applicant/Responsible Party is required to submit to MET a label location drawing or photograph showing the location of the mark on the product. Any reference to MET certification shall not be permitted on any non-eligible product(s), packaging, or literature. If the Applicant/Responsible Party or the Manufacturer applies the FCC identification label to unauthorized products, then the Applicant/Responsible Party and the Manufacturer shall save, indemnify, and hold harmless MET LABORATORIES, INC. from any and all claims which may arise out of said unauthorized action. The label and/or references to MET are permitted on promotional, advertising, and packaging of Certified Product(s) provided that misrepresentation of results of the marking process and/or this agreement do not occur. Final judgment in the suitability of use of the label or the MET Laboratories name is reserved by MET. (continued, next page) MET TCB SERVICE AGREEMENT DOCJ-TCB002 11/24/04 Page of 3 The Applicant/Responsible Party shall maintain or require the manufacturer to maintain a record of all complaints made known to them relating to the product's compliance with the requirements of the relevant standard and agrees to make these records available to MET when requested. The Aplicant/Responsible Party agrees to take appropriate action, or have the manufacturer take appropriate action with respect of such complaints and/or any deficiencies found in products or services that affect compliance with the requirements for certification. Compliance with all requirements and stipulations of the Certification Program and this agreement between MET and the Applicant/Responsible Party is required for program compliance. Non-compliance with all or part of this agreement may result in termination of the agreement and the notification to the FCC to withdraw certification of the product. The Applicant/Responsible Party assumes responsibility for complying with the requirements of the product's certification and this agreement regarding the application of the FCC identification label. The Applicant/Responsible Party understands that any violation of the requirements of this agreement can immediately, at MET's discretion, terminate this agreement. Upon notification by MET, the Applicant/Responsible Party shall immediately take action to correct non-conformance that may have been found during surveillance or during modification to the product by the Applicant/Responsible Party. The Applicant/Responsible Party understands that corrective actions must be immediate. The Applicant/Responsible Party also understands that MET is required to report to the FCC any noted non-compliance. MET will also report corrective actions taken and the status of corrective action. The FCC will determine if any certificate or grants will be withdrawn. Upon termination of this agreement, the Applicant/Responsible Party agrees to remove any references to MET Laboratories from all literature, stationary, packaging, or other promotional media as may have been used by the Applicant/Responsible Party. Additionally, upon termination of this agreement, MET Laboratories will inform the FCC of such termination. The observance of the aforementioned requirements for the product, is a condition for cont…

Text truncated - open the document above for the full version.

SOMA Networks, Inc. 185 Berry Street, Suite 4600 ◦ San Francisco, California 94107 March 8, 2006 ATTN:Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: CONFIDENTIALITY REQUEST FOR SOMAport3, Model # CPE-300-270, FCC ID: POZCPEWCS005239B To Whom It May Concern: This letter serves as an official request for confidentiality under FCC Rule Section 0.459. We have requested that the schematics, block diagrams, modulation description and the operational/technical description required to be submitted with this application be withheld from public review. In view of the fact that the schematics, block diagrams, modulation description and the operational/technical description disclose the mechanism of our process, we ask that these portions (schematics, block diagrams, modulation description and operational/technical description) of our application be withheld from public inspection as provided under FCC section 0.459. These documents contain details of the proprietary operation of our product. These details are not readily discernible from our hardware – even to technically sophisticated individuals – and constitute trade secrets. Please contact me if there is any information you may need. Sincerely, Robin Grindley Chief Scientist – Hardware Systems SOMA Networks, Inc. 185 Berry Street • Suite 4600 • San Francisco CA 94107 • Phone: 415.882.6500 • Fax: 415.882.6512

4.900 1.100 .860 1.026 R.050 TYP .838 DRAWING SCALE 2:1 4 5 6 7 8 7 7 10 11 3 12 13 D C A A B C D 1 3 4 5 6 78 8 7 6 5 4 3 2 1 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF SOMA NETWORKS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF SOMA NETWORKS IS PROHIBITED. PROPRIETARY AND CONFIDENTIAL MATERIAL: FINISH: DRAWN DATE NAME TITLE: SIZE B DWG. NO. REV SHEET 1 OF 1 SCALE: 1:1 REVISIONS REV. COMMENT UNLESS OTHERWISE SPECIFIED: DO NOT SCALE DRAWING LABEL,REGULATORY,MET+FCC,SP3,WCS-AB,[SOMAPORT 300 MODEL CPE-300-270],PRE-PRINTED 005248A 01 tnguyen DIMENSIONS ARE IN INCHES TOLERANCES: ANGULAR: 1 ONE PLACE DECIMAL .1 TWO PLACE DECIMAL .01 THREE PLACE DECIMAL .005 DWG. NO. REV SH 005248A 01 1 10/4/2005 10/4/2005 ENG APPR. MODEL FILE: 005248A.SLDPRT/REV02 9 RELEASE PER EC-04100 01 1. MARK VENDOR NAME, LABEL DESIGNATION, AND SOMA NETWORKS PART NUMBER ON EACH SHEET OF LABELS. 2. BACKGROUND TO BE DARK GRAY (PANTONE COLOR 432C) LETTERING AND GRAPHICS TO BE SILVER. 3. REFER TO APPROPRIATE AGENCY LISTING MARK INFORMATION TO REPLACE REFERENCE SYMBOLS WITH APPROPRIATE REGISTERED MARKS. 4. FONT: ARIAL 24 POINT 5. FONT: ARIAL NARROW 18 POINT 6. FONT: ARIAL 10 POINT 7. FONT: ARIAL 6 POINT 8. FONT: ARIAL 5 POINT 9. LABEL CONSTRUCTION TO CONSIST OF A 0.010" THICK POLYCARBONATE LABEL STOCK WITH A 0.002" THICK 3M #467 PRESSURE SENSITIVE ADHESIVE. SOMA ENGINEERING APPROVED MATERIALS MAY BE SUBSTITUTED. LABEL MUST BE A COMPONENT MARKING AND LABELING SYSTEM APPROVED BY UL AND CSA FOR THE FOLLOWING CONDITIONS: A) INDOOR B) TEMPERATURE RANGE: -40C TO +55C WHEN AFFIXED TO GE CYCOLOY C6200 (PC/ABS BLEND) 10. PRINT “FCC ID: POZCPEWCS005239B” AT NOTED LOCATION. 11. PRINT “LISTING # E112355” AT NOTED LOCATION. 12. PLACE MET LOGO (MET1US.GIF) IN NOTED LOCATION. 13. FONT: ARIAL NARROW 6 POINT 14. LABEL IS SIMILAR TO 004888A REV 03 WITH CHANGES FROM THIS LABEL NOTED WITH A . 8 4 PLACES 2 2 3 4 5 12 1 3 3 3 5 5 5 5 6 4 EXPLODED VIEW 9 10 7 7 ASSEMBLED VIEW D C A A B C D 1 345678 8 7 654321 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF SOMA NETWORKS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF SOMA NETWORKS IS PROHIBITED. PROPRIETARY AND CONFIDENTIAL MATERIAL: FINISH: DRAWN DATE NAME TITLE: SIZE B DWG. NO. REV SHEET 1 OF 1 SCALE: 1:3 REVISIONS REV.COMMENT UNLESS OTHERWISE SPECIFIED: DO NOT SCALE DRAWING ASSY DWG MX,SYSTEM,SP3 ADM-000057 thnguyen DIMENSIONS ARE IN INCHES TOLERANCES: ANGULAR: 1 ONE PLACE DECIMAL .1 TWO PLACE DECIMAL .01 THREE PLACE DECIMAL .005 DWG. NO. REV SH ADM-000057 1 8/12/2004 8/12/2004 bbonn ENG APPR. MODEL FILE: SP3_ASM_TRI.SLDPRT/REV05 01 01 01 INITIAL RELEASE PER EC-03353 NOTES: (UNLESS OTHERWISE SPECIFIED) 1. ASSEMBLE UNIT PER INSTRUCTIONS BELOW (NOTES 2-7): 2. TORQUE SCREW, ITEM 8, TO 8±1 IN-LBS. 3. ASSEMBLE ITEMS 4 AND 5, EMI CONTACTS TO RIGHT AND LEFT, INTO PINS OF THE ITEM 2, BOTTOM CASE. PRESS DOWN UNTIL SURFACES MEET. 4. SLIDE ITEM 1, CHASSIS/PCA ASSEMBLY, INTO ITEM 2, BOTTOM CASE. FOUR HOLES IN ITEM 1 ALIGN WITH HOLES IN ITEM 2. 5. PLACE ITEM 3, TOP CASE, OVER ITEM 2, BOTTOM CASE. ASSEMBLE ITEM 3 TO THE ITEM 1, CHASSIS/PCA ASSEMBLY, AND ITEM 2, BOTTOM CASE, USING SCREWS, ITEMS 8 (4X). 6. PLUG RUBBER FEET, ITEMS 12 (4X), INTO HOLES IN BOTTOM OF ITEM 2. PRESS IN UNTIL SURFACES MEET. 7. PLACE ITEM 9, REGULATORY LABEL, AND ITEM 10, SERIAL NUMBER LABEL, IN DETENT ON BOTTOM OF ITEM 2. LABELS TO BE APPROXIMATELY .020 IN FROM EDGE OF LABEL DETENT AND APPROXIMATELY .060 IN FROM EACH OTHER.

SOMA Networks, Inc. 185 Berry Street, Suite 4600 ◦ San Francisco, California 94107 March 8, 2006 ATTN:Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: Tune-up Procedure for SOMAport3, Model # CPE-300-270, FCC ID: POZCPEPCS005239B To Whom It May Concern: The EUT with SOMA Model number CPE-300-270 is tuned and calibrated solely during the manufacturing process at the factory. It is neither necessary nor possible for a user to perform such a tune-up procedure. Sincerely, Robin Grindley Chief Scientist – Hardware Systems SOMA Networks, Inc. 185 Berry Street • Suite 4600 • San Francisco CA 94107 • Phone: 415.882.6500 • Fax: 415.882.6512

SOMA Networks, Inc. 185 Berry Street, Suite 4600 ◦ San Francisco, California 94107 March 8, 2006 ATTN:Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: MPE Calculation for SOMAport3, Model # CPE-300-270, FCC ID: POZCPEWCS005239B To Whom It May Concern: The RF exposure limits for radio transmitters are given in 47 CFR 1.1310. The EUT operates at 2305-2315 MHz and is intended for home use. Therefore the applicable exposure limits are in Table 1, section B (for General Population/Uncontrolled Exposure). The applicable Power Density limit for 1500-100,000 MHz from Table 1 is: 1 mW/cm 2 The CPE-300-270 is intended for use at distances of >20cm from the user, and this safety requirement is explicitly stated in the user manual. The CPE-300-200 has the following transmitter operating parameters in the maximal case: Maximum Transmitter Power (P): +27 dBm Maximum Numerical Antenna Gain (G): +5 dBi As per FCC Bulletin 65, the formula used to calculate the exposure level, S (in mW/cm 2 ) at a distance R=20 cm is: 2 5026 16.3501 4 /315.0 22 cmmWS cm mW R PG === × π Thus the CPE-300-270 is below the MPE limit of 1 mW/cm 2 at a distance of 20 cm. Sincerely, Robin Grindley Chief Scientist – Hardware Systems SOMA Networks, Inc. 185 Berry Street • Suite 4600 • San Francisco CA 94107 • Phone: 415.882.6500 • Fax: 415.882.6512

MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 33439 WESTERN AVENUE ! UNION CITY, CALIFORNIA 94587-3201 ! PHONE (510) 489-6300 ! FAX (510) 489-6372 DOC-EMC704 4/5/2005 Certificates and reports shall not be reproduced except in full, without the written permission of MET Laboratories, Inc. Electromagnetic Compatibility Criteria Test Report For the SOMA Networks Soma Port 300 Model CPE-300-270 Tested under FCC Certification Rules Title 47 of the CFR, Part 27 C & D and Part 15 Subpart B for a Class B MET Report: EMCS17858B-FCC27 November 10, 2005 Prepared For: SOMA Networks 185 Berry Street, Suite 4600 San Francisco, California 94107 Prepared By: MET Laboratories, Inc. 33439 Western Ave. Union City, California 94587 SOMA Networks Soma Port 300 Model CPE-300-270 CFR Title 47 Part 27 Subpart C and D and Part 15 Subpart B MET Report: EMCS17858B-FCC27 © 2005, MET Laboratories, Inc. Page i of v DOC-EMC704 4/5/2005 Electromagnetic Compatibility Criteria Test Report For the SOMA Networks Soma Port 300 Model CPE-300-270 Tested Under FCC Certification Rules Title 47 of the CFR, Part 27 C & D and Part 15 Subpart B for a Class B Shawn McMillen, Project Engineer Cheryl Anicete Electromagnetic Compatibility Lab Documentation Department Engineering Statement: The measurements shown in this report were made in accordance with the procedures indicated, and the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. It is further stated that upon the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of Part 27 C & D and Part 15 Subpart B of the FCC Rules under normal use and maintenance. Tony Permsombut, Manager Electromagnetic Compatibility Lab SOMA Networks Soma Port 300 Model CPE-300-270 CFR Title 47 Part 27 Subpart C and D and Part 15 Subpart B MET Report: EMCS17858B-FCC27 © 2005, MET Laboratories, Inc. Page ii of v DOC-EMC704 4/5/2005 Report Status Sheet Revision Report Date Reason for Revision ∅ November 10, 2005 Initial Issue. SOMA Networks Soma Port 300 Model CPE-300-270 CFR Title 47 Part 27 Subpart C and D and Part 15 Subpart B MET Report: EMCS17858B-FCC27 © 2005, MET Laboratories, Inc. Page iii of v DOC-EMC704 4/5/2005 Table of Contents 1. Testing Summary ............................................................................................................................................................1 2. Equipment Configuration...............................................................................................................................................3 2.1. Overview....................................................................................................................................................................3 2.2. Test Site .....................................................................................................................................................................4 2.3. Description of Test Sample ........................................................................................................................................4 2.4. Equipment Configuration...........................................................................................................................................5 2.5. Support Equipment ....................................................................................................................................................5 2.6. Ports and Cabling Information ...................................................................................................................................6 2.7. Mode of Operation .....................................................................................................................................................8 2.8. Method of Monitoring EUT Operation ......................................................................................................................8 2.9. Modifications .............................................................................................................................................................8 2.9.1. Modifications to EUT .............................................................................................................................8 2.9.2. Modifications to Test Standard ...............................................................................................................8 2.10. Disposition of EUT ..................................................................................................................................................8 3. Electromagnetic Compatibility RF Power Output Requirements ..............................................................................9 3.1. RF Power Output .......................................................................................................................................................9 4. Electromagnetic Compatibility Modulation Characteristics Requirements............................................................10 4.1. Modulation Characteristics ......................................................................................................................................10 5. Electromagnetic Compatibility Occupied Bandwidth Requirements.......................................................................11 5.1. Occupied Bandwidth ................................................................................................................................................11 6. Electromagnetic Compatibility Emissions Requirements .........................................................................................14 6.1. Spurious Emissions at Antenna Terminals.......................................................................…

Text truncated - open the document above for the full version.