PQ4IPROI5230GSM Mobile Phone

GSM Mobile Phone I5230 User’s Manual Contents 1 General Information .......................................................................................................................3 1.1 Introduction .........................................................................................................................3 1.2 Safety ..................................................................................................................................3 1.3 Warning and Notice.............................................................................................................4 1.3.1 Basic Notices................................................................................................................... 4 1.3.2 Notices of Your Phone .....................................................................................................4 1.3.3 Notices of Battery Use..................................................................................................... 5 1.3.4 Notices of Charger Use ...................................................................................................5 1.3.5 Care and Maintenance .................................................................................................... 6 1.3.6 General Notices............................................................................................................... 6 2 Getting Started ...............................................................................................................................7 2.1 Overview and Introduction .................................................................................................7 2.1.1 Product Specification ...................................................................................................... 7 2.2 Keypad ................................................................................................................................7 2.3 Battery .................................................................................................................................7 2.4 Network Connections..........................................................................................................8 2.4.1 SIM Card ......................................................................................................................... 8 2.4.2 Insert and Remove the SIM Card .................................................................................... 8 2.4.3 Turn Your Phone On or Off ............................................................................................. 8 2.4.4 Phone unlock................................................................................................................... 9 2.4.5 Unlock the SIM Card.......................................................................................................9 2.4.6 Connect to the Network ...................................................................................................9 2.4.7 Make Calls ...................................................................................................................... 9 2.4.8 Make Domestic Calls .................................................................................................... 10 2.4.9 Dial Extension............................................................................................................... 10 2.4.10 International telephone Calls...................................................................................... 10 2.4.11 Dial the Numbers of Phonebook.................................................................................. 10 2.4.12 Emergency Number ......................................................................................................11 2.4.13 Answer Calls ................................................................................................................11 2.4.14 Call Records .................................................................................................................11 2 2.4.15 Call Menu.....................................................................................................................11 3 Function Menus............................................................................................................................12 3.1 Use of Function Menus .....................................................................................................12 Scroll Searching and Selection Function ............................................................................... 12 Exit Menus.............................................................................................................................. 12 3.2 Call Center ........................................................................................................................12 3.2.1 Call history .....................................................................................................................12 3.3 Phonebook.........................................................................................................................13 3.4 Messages ...........................................................................................................................13 3.4.1 SMS ............................................................................................................................... 13 3.4.1.1 Write Message .............................................................................................14 3.4.1.2 Inbox ...........................................................................................................14 3.4.1.3 Outbox.........................................................................................................14 3.4.1.4 Draft ............................................................................................................14 3.4.1.5 SMS Settings ...........................................................…

Text truncated - open the document above for the full version.

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS EUT– Front View (Color 1) EUT– Rear View (Color 1) EUT– Top View (Color 1) EUT – Bottom View (Color 1) EUT– Left View (Color 1) EUT – Right View (Color 1) EUT– Front View (Color 2) EUT– Rear View (Color 2) EUT– Top View (Color 2) EUT – Bottom View (Color 1) EUT– Left View (Color 2) EUT – Right View (Color 2) EUT – Headset View EUT – USB Cable View EUT – Adapter View

EXHIBIT A - FCC ID LABELING AND LOCATION FCC ID Label FCC ID Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925) Label here

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS EUT – Battery off View EUT – Cover off View GSM Antenna EUT – Main Board Top View 1 EUT – Main Board Top View 2 EUT – Main Board Top View 3 EUT – Main Board Bottom with Speaker View EUT – Main Board Bottom without Speaker View EUT – Main Board Bottom Shielding off View Bluetooth Antenna EUT – LCD Top View EUT – LCD Bottom View EUT – Battery Top View EUT – Battery Bottom View

1 Tune-Up Procedure Tune-Up TX Content 1 Purpose............................................................................................................................. 2 2 General description ..........................................................................................................3 2.1 Characteristics of the transmit burst..................................................................... ......3 2.2 GPRS Data Transfer......................................................................................................3 2.2.1 GSM850&PCS1900 allowed maximum output reduction in a multislot Configuration.......................................................................................................................3 3 Parameters........................................................................................................................ 4 3.1 Parameters used to shape the burst....................................................................... ......4 3.2 Parameters used to define the temporal position of the burst....................................... 4 3.2.1 Optimum position of the burst................................................................................... 4 3.2.2 Optimum length of the burst...................................................................................... 5 4 Operating mode ................................................................................................................5 4.1 How to transmit a Tch burst (Random data), in GSM850 PCS1900 mode, at power control level max: ................................................................ 5 4.2 How to stop Tx measurements: .................................................................................... 5 4.3 How to transmit a burst after modifying parameters.................................................... 6 5 Purpose............................................................................................................................. 6 6 Automatic frequency control ...........................................................................................6 7 Static frequency error and range......................................................................................8 2 1 Purpose This panel gives the possibility to manage the mobile in the transmit mode. This window includes both: - All the parameters (frequency band, RF channel, RF level to get the desire antenna output power...) The user needs to make the mobile transmitting, - All the parameters needed to define a transmit burst, - All the compensation table to be able to align the mobile in production. This Tx_commands user guide is describing: - The characteristics of the transmit burst, - All the parameters used in the transmit mode, - The operating mode to make the mobile transmitting 3 2 General description 2.1 Characteristics of the transmit burst The power levels and the shape of a transmit burst are controlled by the power amplifier controller integrated in the CT8852/53. The burst is generated by a 10-bit DAC from the CT8852/53 as shown below: The ramping shape is referenced with the rising edge of Tx-ON (from the Baseband). There are two types of parameters define the transmit burst: the first one define the shapes of the burst, and the second one define the temporal position of the burst. The rising and the falling edge of the transmit burst are determined by a set of 32 DAC code values n = 0 ... 31. Tru = TxTRUDefault + △TRU_P + △TRU_T Trd = TxTRD_NBDefault + △TRD_P (for a normal burst). Trd = TxTRD_ABDefault + △TRD_P (for an access burst). 2.2 GPRS Data Transfer GSM mobile phones use a Time Division Multiple Access (TDMA) scheme to transmit data. The TDMA format contains eight time slots. The handset power amplifier typically transmits in two of these up time slots. To prevent interference between cell phones, the time mask profile as specified is very restricted. To meet the GSM time mask, the output power of the PA needs to ramp up and down very quickly while staying within the time mask and not generating extraneous frequency bursts due to too abrupt ramp profiles. As described before, the Vramp input value sets the RF output 4 power. By applying a certain ramp profile to the Vramp pin, the power level (Pout) of the PA is set to obtain the required time mask. A time mask of the PA’s output power is displayed. The time mask meets the limits (displayed by green lines) over a wide range of temperature, voltage and load variations. 3 Parameters F (n) are values coming from the DAC to shape the transmit burst. Some F(n) values have a corresponding Parameter used in the TAT to align the mobiles. Parameter used in TAT = [F (n)]. 3.1 Parameters used to shape the burst - H0 = [F (1)] controls the rate at which energy is given to the control loop at the beginning of the ramp. This energy is needed to bring the PA system control in a closed loop. This is the second code coming from the CT8852/53 DAC. - PeakPow = [F (15)] corresponds to the peak power of the transmit burst. - H30 = [F (30)] corresponds to the last ramping coefficients used to shape the ramp. - MinPow = [F (31)] is a fixed parameter and corresponds to the Code Start of the CT8852/53 specification. It ensures a fast discharge of accumulated energy during the open loop mode in the summing node. 3.2 Parameters used to define the temporal position of the burst 3.2.1 Optimum position of the burst This parameter is TRU (or △TRU_P) on the panel, in the Optimal Burst. This is the burst starting time correction, which is optimised for each power control level. 5 (Note that _P means that the parameter is a power compensation parameter). 3.2.2 Optimum length of the burst This parameter is TRD (or △TRD_P) on the panel, in the Optimal Burst. This is the burst length compensation, which is optimized for each power control level. (Note that _P means that the parameter is a power compensation parameter). 4 Operating mode 4.1…

Text truncated - open the document above for the full version.

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and shall be marked with an asterisk “★＂ SAR EVALUATION REPORT For HONG KONG IPRO TECHNOLOGY CO., LIMITED ROOM C1D, 6/F, WING HING INDUSTRIAL BUILDING, 14 HING YIP STREET, KWUN TONG, KOWLOON, HONG KONG FCC ID: PQ4IPROI5230 Report Type: Original Report Product Type: GSM Mobile Phone Test Engineer: Sandy Wang Report Number: RSZ120829002-20 Report Date: 2012-09-25 Reviewed By: Alvin Huang RF Leader Test Laboratory: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Shenzhen) Report No: RSZ120829002-20 SAR Evaluation Report 2 of 91 Attestation of Test Results Company Name HONG KONG IPRO TECHNOLOGY CO., LIMITED EUT Description Mobile Phone FCC ID PQ4IPROI5230 Model Number I5230 EUT Information Test Date 2012.09.04-2012.09.05 Frequency Max. SAR Level(s) Measured Limit (W/Kg) Cellular Band 0.335 W/kg, 1g Head SAR 0.599 W/kg, 1g Body SAR PCS Band 0.253 W/kg, 1g Head SAR 0.380 W/kg, 1g Body SAR 1. 6 ANSI/IEEE C95.1: 2005 IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fileds,3 kHz to 300 GHz. ANSI/IEEE C95.3: 2002 IEEE Recommended Practice for Measurements and Computations of Radio Frequency Electromagnetic Fields With Respect to Human Exposure to SuchFields,100 kHz—300 GHz. OET BULLETIN 65 SUPPLEMENT C Evaluating Compliance with FCC Guidelines for Human Exposure To Radiofrequency Electromagnetic Fields Applicable Standards IEEE1528: 2003 IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques Note: This wireless device has been shown to be capable of compliance for localized specific absorption rate (SAR) for General Population/Uncontrolled Exposure limits specified in ANSI/IEEE Standards and has been tested in accordance with the measurement procedures specified in FCC OET 65 Supplement C and IEEE 1528-2003. The results and statements contained in this report pertain only to the device(s) evaluated. Bay Area Compliance Laboratories Corp. (Shenzhen) Report No: RSZ120829002-20 SAR Evaluation Report 3 of 91 TABLE OF CONTENTS DOCUMENT REVISION HISTORY .........................................................................................................................4 EUT DESCRIPTION ....................................................................................................................................................5 TECHNICAL SPECIFICATION.........................................................................................................................................5 REFERENCE, STANDARDS AND GUILDELINES ................................................................................................6 SAR LIMITS.................................................................................................................................................................7 FACILITIES AND ACCREDITATION .....................................................................................................................8 DESCRIPTION OF TEST SYSTEM ..........................................................................................................................9 EQUIPMENT LIST AND CALIBRATION .............................................................................................................16 EQUIPMENTS LIST & CALIBRATION INFORMATION....................................................................................................16 SAR MEASUREMENT SYSTEM VERIFICATION ..............................................................................................17 LIQUID VERIFICATION...............................................................................................................................................17 SYSTEM ACCURACY VERIFICATION...........................................................................................................................20 SAR SYSTEM VALIDATION DATA .....................................................................................................................21 EUT TEST STRATEGY AND METHODOLOGY .................................................................................................29 TEST POSITIONS FOR DEVICE OPERATING NEXT TO A PERSON’S EAR........................................................................29 CHEEK/TOUCH POSITION...........................................................................................................................................30 EAR/TILT POSITION...................................................................................................................................................30 TEST POSITIONS FOR BODY-WORN AND OTHER CONFIGURATIONS..............................................................................31 SAR EVALUATION PROCEDURE.................................................................................................................................32 CONDUCTED OUTPUT POWER MEASUREMENT ...........................................................................................33 TEST BLOCK DIAGRAM AND PROCEDURE..................................................................................................................33 TEST RESULTS........................................................................…

Text truncated - open the document above for the full version.

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and shall be marked with an asterisk “★” FCC PART 22H, PART 24E TEST REPORT For HONG KONG IPRO TECHNOLOGY CO., LIMITED ROOM C1D, 6/F, WING HING INDUSTRIAL BUILDING, 14 HING YIP STREET, KWUN TONG, KOWLOON, HONG KONG FCC ID: PQ4IPROI5230 Report Type: Original Report Product Type: GSM Mobile Phone Test Engineer: Jimmy Xiao Report Number: RSZ120829002-00C Report Date: 2012-09-18 Reviewed By: Suny Sun EMC Engineer Test Laboratory: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ120829002-00C FCC Part 22H/24E Page 2 of 29 TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................4 OBJECTIVE...................................................................................................................................................................4 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................4 TEST METHODOLOGY..................................................................................................................................................4 TEST FACILITY.............................................................................................................................................................5 SYSTEM TEST CONFIGURATION ..........................................................................................................................6 DESCRIPTION OF TEST CONFIGURATION......................................................................................................................6 EQUIPMENT MODIFICATIONS.......................................................................................................................................6 BLOCK DIAGRAM OF TEST SETUP................................................................................................................................6 SUMMARY OF TEST RESULTS ...............................................................................................................................7 FCC §1.1307 & §2.1093 - RF EXPOSURE..................................................................................................................8 APPLICABLE STANDARD..............................................................................................................................................8 TEST RESULT...............................................................................................................................................................8 FCC §2.1047 - MODULATION CHARACTERISTIC ..............................................................................................9 FCC § 2.1046, § 22.913 (A) & § 24.232 (C) - RF OUTPUT POWER......................................................................10 APPLICABLE STANDARD............................................................................................................................................10 TEST PROCEDURE......................................................................................................................................................10 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................10 TEST DATA................................................................................................................................................................11 FCC §2.1049, §22.917, §22.905 & §24.238 – EMISSION BANDWIDTH...............................................................13 APPLICABLE STANDARD............................................................................................................................................13 TEST PROCEDURE......................................................................................................................................................13 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................13 TEST DATA................................................................................................................................................................13 FCC §2.1051, §22.917(A) & §24.238(A) - SPURIOUS EMISSIONS AT ANTENNA TERMINALS ..................17 APPLICABLE STANDARD............................................................................................................................................17 TEST PROCEDURE......................................................................................................................................................17 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................17 TEST DATA................................................................................................................................................................17 FCC §2.1053, §22.917 & §24.238 - SPURIOUS RADIATED EMISSIONS ...........................…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Radiated Emissions Test View (Below 1 GHz) Radiated Emissions Test View (Above 1 GHz) Frequency Stability Test View