PQ4IPROK1Mobile Phone

m of 5mm from the body. K1 5. 3D stereo sound FCC Warning Specific Absorption Rate (SAR) information SAR tes ts are conducted using standard operating positions accepted by the FCC with the phone transmitting at its highest certified power level in all tested frequenc y bands, although the SAR is determined at the high est certified power level, the actual SAR level of the phone while operating can be well below the maxim um value, in general, the closer you are to a wireles s base station antenna, the lower the power output. Before a new model phone is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit establishe d by the FCC, Tests for each phone are performed i n positions and locations (e.g. at the ear and worn o n the body)as required by the FCC. For body worn operation, this mobile phone has bee n tested and meets the FCC RF exposure guideline s when used with an accessory designated for this p roduct or when used with an accessory that contain s no metal and that positions the handset a minimu This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference rec eived, including interference that may cause undesir ed operation. Any Changes or modifications not exp ressly approved by the party responsible for complia nce could void the user’s authority to operate the eq uipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pu rsuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against h armful interference in a residential installation. This equipment generates uses and can radiate radio fre quency energy and, if not installed and used in acco rdance with the instructions, may cause harmful inte rference to radio communications. However, there is no guarantee that interference will not occur in a par ticular installation. If this equipment does cause har mful interference to radio or television reception, wh ich can be determined by turning the equipment off and on, the user is encouraged to try to correct the i nterference by one or more of the following measur es: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment an d receiver. --Connect the equipment into an outlet on a circuit di fferent from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV tec hnician for help. 6.the cell broadcast Enter Message menu to view Broadcast list The purpose of cell broadcasting is to inform mobile phone users of the danger, such as serious threats, child abduction and so on, through some alerts issued by operators,the function is activated by default

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS Bluetooth Antenna 2G/3G Antenna

TEST REPORT Applicant: HONG KONG IPRO TECHNOLOGY CO.,LIMITED Address: 12/F,3 LOCKHART ROAD,WANCHAI ,HK FCC ID: PQ4IPROK1 Product Name: Mobile Phone Standard(s): 47 CFR Part 15 Subpart B ANSI C63.4-2014 The above equipment has been tested and found compliance with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR22030023-00B Date Of Issue: 2022-04-22 Reviewed By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR22030023-00B Page 2 of 22 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR22030023-00B Page 3 of 22 CONTENTS TEST FACILITY ............................................................................................................................................................. 2 DECLARATIONS ............................................................................................................................................................ 2 1. GENERAL INFORMATION ................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 4 1.2 DESCRIPTION OF TEST CONFIGURATION ................................................................................................................ 5 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 6 1.3 MEASUREMENT UNCERTAINTY .............................................................................................................................. 7 2. SUMMARY OF TEST RESULTS ........................................................................................................................... 8 3. REQUIREMENTS AND TEST PROCEDURES ................................................................................................... 9 3.1 AC LINE CONDUCTED EMISSIONS .......................................................................................................................... 9 3.1.1 EUT Setup...................................................................................................................................................... 9 3.1.2 EMI Test Receiver Setup ............................................................................................................................... 9 3.1.3 Test Procedure ............................................................................................................................................. 10 3.1.4 Corrected Amplitude & Margin Calculation ................................................................................................ 10 3.2 RADIATION SPURIOUS EMISSIONS ........................................................................................................................ 11 3.2.1 EUT Setup.................................................................................................................................................... 11 3.2.2 EMI Test Receiver Setup ............................................................................................................................. 12 3.2.3 Test Procedure ............................................................................................................................................. 12 3.2.4 Corrected Amplitude & Margin Calculation ................................................................................................ 12 4. TEST DATA AND RESULTS ................................................................................................................................ 13 4.1 AC LINE CONDUCTED EMISSIONS ........................................................................................................................ 13 4.2 RADIATION SPURIOUS EMISSIONS ........................................................................................................................ 16 China Certification ICT Co., Ltd (Dongguan) Report No.: CR22030023-00B Page 4 of 22 1. GENERAL INFORMATION 1.1 Product Description for Equipment under Test (EUT) EUT Name: Mobile Phone EUT Model: K1 Highest Operation Frequency: 2480 MHz Rated Input Voltage: DC 3.7V from battery or DC 5V from adapter Serial Number: CR22030023-RF-S1/3 EUT Received Date: 2022.3.10 EUT Received Status: GOOD Accessory Information: Accessory Description M…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions Front View Conducted Emissions Side View Radiated Emission Below 1G front View Radiated Emission Below 1G rear View Radiated Emission Above 1G front View Radiated Emission Above 1G rear View