PQN44319TXFighter Jet

® INSTRUCTION GUIDE The Air Hogs ® F-14 Tomcat ® is a revolutionary radio controlled jet that is a true backyard flyer. You can hand toss or take off from the ground using the landing gear. The F-14 Tomcat ® uses digital proportional control which provides hobby like flight performance. Controller/Charger A ntenna ON/OFF/CHARGE Switch Throttle Charge Door (to access Charge Nozzle) C harge L ED Power LED Left/Right Toggle Steering Trim Knob Main Wing Propeller F-14 Tomcat ® Vertical Stabilizers Propeller Fuselage Wheels Main Wing Nose Wheel Fuselage 1 1.Open the battery door with a screwdriver. 2.If used batteries are present, remove these batteries from the unit by pulling up on one end of each battery. 3.Install new batteries as shown in the polarity diagram (+/-) inside the battery compartment. 4.Replace battery door securely. 5.Check your local laws and regulations for correct recycling and/or battery disposal. Controller/Charger Battery Compartment Door 6 x AA 1.5-V Alkaline Batteries IMPORTANT TIP: TURN YOUR CONTROLLER ON TO ENSURE THAT THE BATTERIES ARE INSTALLED PROPERLY. THE RED LED LIGHT ON THE FRONT OF THE CONTROLLER SHOULD TURN RED. After each flight, store the jet in the package to prevent damage. REPAIRS CONTROLLER/CHARGER BATTERY INSTALLATION If the wings on your jet get damaged they can be easily repaired with clear tape as shown. ADDING WHEELS TO THE F-14 TOMCAT ® Repair Attach the front and rear wheels to the jet as shown. The wires on the wheels slide into the slots on the jet and clip into place. Battery Compartment Your F-14 Tomcat ® jet has a preinstalled rechargeable battery in the jet’s fuselage. Because the Controller’s AA batteries are used for 2 functions – charging and controlling, they will need to be replaced every so often. Antenna rePLICA SERIES Contents: 1 x Air Hogs ® F-14 Tomcat ® 1 x Remote Control/Charger, 1 x Instruction Guide 3 x Landing Gear, 2 X Spare Props PRE-FLIGHT ENVIRONMENT CHECK CHARGING YOUR F-14 TOMCAT ® Set the controller/ charger switch to CHARGE. 4 .Carefully p ush the charge n ozzle all the w ay into the jet’s charge port located on the bottom of the jet. FLYING INSTRUCTIONS Fully extend controller/charger antenna. Push the controller/ charger switch to ON. Power light will turn RED. 1 2 3 5 5.During the charging process, the green charge light will turn ON. When the jet is completely charged, the green charging light will turn OFF. 6. Remove charge nozzle gently from the jet’s charge port. Store charge nozzle and close the charge door. 5 Important Charging Information: • Before taking your initial flight, charge the jet for a complete charge cycle on your charger. • Depending upon the length of future play, you will not need to complete a full charge before each flight. NOTE:A shortened charge results in a shorter playtime (may take up to 30-40 minutes to fully charge). Green Charge Light 1. Location – Fly in a large wide open, grassy location that is free of buildings, trees, overhead wires, and other obstructions.Do not fly near people or animals. 2. Weather –Fly on mild, sunny days. Do not fly in electrical storms, rain, sleet, snow or other adverse weather conditions. Do not fly if the temperature is below 7°C/45°F. In very cold temperatures, the jet will become fragile and the engine performance will decrease. 3. Wind Conditions –Do not fly in strong winds. Strong winds may overpower the aircraft and make it difficult to control. 5 NOTE: We recommend that you start flying by hand launching to get used to the controls. When preparing for take-off, check the direction of the wind. Always launch the jet against the wind for best take-off and flight results. Use your left hand to apply at least half throttle on the controller/charger. Gently toss the jet forward into the wind and parallel to the ground. Refrain from using the directional toggle while launching the jet. 1.Push the ON/OFF switch on the bottom of the jet to the LEFTto turn the jet OFF. 2. Set the controller/charger switch to OFF. 3.Flip the charge door open to reveal the charge nozzle. 6 If you are taking off from the ground, make sure you are on a smooth paved surface, and put the throttle all the way forward for fast acceleration. 4 Push the jet’s ON/OFF switch to the right to turn the jet to ON. 2 4 CONTROLLING JET FLIGHT Turn the controller/ charger OFF by pulling the switch down. LEFT TURN Move the direction toggle to the left. If you want to straighten out your flight path, turn the Steering Trim Knobto the left or right during flight. FLIGHT ADJUSTMENTS ONCE THE JET HAS LANDED Steering Trim Knob Controller/Charger 2 1 To ACCELERATE or climb Push the throttle (left toggle) forward. RIGHT TURN Move the direction toggle to the right. Controller/Charger TO LAND Select a soft grassy area and pull the throttle (left toggle) back slowly and then release. For example: To make the jet move to the LEFT, move the toggle to the RIGHT. CONTROL REVERSAL IMPORTANT: When the jet is flying towards you, the controls are reversed. Turn jet OFFby pushing switch to the left. 3 4 Hereby, Spin Master Ltd., declares that this F-14 Tomcat ® is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. <http://www.airhogs.com> Warning! CHOKING HAZARD – Small Parts. Contains 1 x 3.7V LiPo battery pack. Batteries or battery packs must be recycled or disposed of properly. When this product has reached the end of its useful life it should not be disposed of with other household waste. The Waste Electrical and Electronic Equipment Regulations require it to be separately collected so that it can be treated using the best available recovery and recycling techniques. This will minimize the impact on the environment and human health from soil and water contamination by any hazardous substances, decrease the resources required to make new products and avoid using up landfill space. Please do your part by keeping this product out of the municipal waste stream…

Text truncated - open the document above for the full version.

Model: 44319 TX Block diagram RF Amplifier ANT BATTERY Encoding Circuit CRYSTAL OSC 27.145MHz FOR WARD LEFT/RIGHT In t erfa c e Circuit CHARGING Circuit FCC ID: PQN44319TX 27.145MHz 9VDC ( Q2 ) (Y1) (U2) (Q3,Q4,Q6,D2) (SW2, SW3) (VR1) (Q5, R9, R10) (Q1)

INTERTEK TESTING SERVICE Report No.: HK11080263-1 FCC ID: PQN44319TX Equipment Photographs Model : 44319 (External)

27MHz TX FCC ID:PQN44319TX This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 50mmX15mm Label Size Letter Height 1 mm Letter Height 1.2 mm

INTERTEK TESTING SERVICE Report No.: HK11080263-1 FCC ID: PQN44319TX Equipment Photographs Model: 44319 (Internal) INTERTEK TESTING SERVICE Report No.: HK11080263-1 FCC ID: PQN44319TX Equipment Photographs Model: 44319 (Internal) INTERTEK TESTING SERVICE Report No.: HK11080263-1 FCC ID: PQN44319TX Equipment Photographs Model: 44319 (Internal) INTERTEK TESTING SERVICE Report No.: HK11080263-1 FCC ID: PQN44319TX Equipment Photographs Model: 44319 (Internal) INTERTEK TESTING SERVICE Report No.: HK11080263-1 FCC ID: PQN44319TX Equipment Photographs Model: 44319 (Internal)

FCC ID: PQN44319TX Model: 44319 (Transmitter portion) Technical Description of Transmitter The transmitter operates at 27.145 MHz, and controls a receiver to move forward, left and right. The Transmitter is powered by 6 X 1.5V "AA" batteries. The circuit of the transmitter comprises of, 1. Encoding IC (U2) with left/right control switches (SW2, SW3), forward speed control lever (VR1) and interface circuit (Q5, R9, R10). 2. 27.145MHz Crystal Oscillator (Y1). 3. RF modulator (Q1). 4. RF amplifier (Q2) 5. Battery charging circuit (Q3, Q4, Q6, D2). Antenna Type: external, integral and non-detachable antenna. Modulation Type: Pulse Modulation 27.145MHz (single channel)

Model: 44319 Tx FCC ID: PQN44319TX

INTERTEK TESTING SERVICES Report No.: HK11080263-1 FCC ID: PQN44319TX Code: FCC15C_f / Effective Date: 24 Jun 2011 ( of ) Bandwidth / Bandedge Plot – Pursuant to FCC Part 15 Section 15. 227 Requirement (Pass/Fail)

- The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. - This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com TEST REPORT Report No.: HK11080263-1 Spin Master Toys Far East Ltd. Application For Certification Original Grant (FCC ID: PQN44319TX) Transmitter Prepared and Checked by: Approved by: Signed On File Wong Cheuk Ho, Herbert Engineer Chan Chi Hung, Terry Assistant Supervisor Date: September 05, 2011 INTERTEK TESTING SERVICES Report No.: HK11080263-1 FCC ID: PQN44319TX i GENERAL INFORMATION Spin Master Toys Far East Ltd. BRAND NAME: Spin Master Ltd. MODEL: 44319 FCC ID: PQN44319TX Grantee: Spin Master Toys Far East Ltd. Grantee Address: Room 1113, 11/F., Chinachem Golden Plaza, 77 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong. Contact Person: Philips Tan Tel: 86769 81080068 Fax: 86769 81080061 e-mail: [email protected] Manufacturer: Lamsun Manufacturer Address: Song baitang, Changping, Dong guan Guang dong, Province Brand Name: Spin Master Ltd. Model: 44319 Additional Model: 1015111, 6013728, 1019523, 6015940, 1021502, 6010469, 1013185, 6012633, 1017351, 6010469, 1019671, 6016029 Type of EUT: Transmitter Description of EUT: Fighter Jet (44319), A10 Warthog (1015111, 6013728, 1019523, 6015940), A10 Warthog & F14 (1021502, 6010469), F14 (1013185, 6012633, 1017351, 6010469, 1019671, 6016029) Serial Number: N/A FCC ID: PQN44319TX Date of Sample Submitted: August 04, 2011 Date of Test: August 08, 2011 Report No.: HK11080263-1 Report Date: September 05, 2011 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% INTERTEK TESTING SERVICES Report No.: HK11080263-1 FCC ID: PQN44319TX ii SUMMARY OF TEST RESULT Spin Master Toys Far East Ltd. BRAND NAME: Spin Master Ltd. MODEL: 44319 FCC ID: PQN44319TX TEST SPECIFICATION REFERENCE RESULTS Maximum Peak Output Power 15.247(b), (c) / RSS-210 A8.4 N/A Hopping Channel Carrier Frequencies Separation (for 2.4GHz Digital) 15.247(e) / RSS-210 A8.1 N/A 20dB Bandwidth of the Hopping Channel 15.247(a) / RSS-210 A8.1 N/A Number of Hopping Frequencies 15.247(e) / RSS-210 A8.1 N/A Average Time of Occupancy of Hopping Frequency 15.247(e) / RSS-210 A8.1 N/A Anteann Conducted Spurious Emissions 15.247(d) / RSS-210 A8.5 N/A Radiated Spurious Emissions 15.247(d) / RSS-210 A8.5 N/A RF Exposure Compliance 15.247(i) / RSS-Gen 5.5 N/A Transmitter Power Line Conducted Emissions 15.207 / RSS-Gen 7.2.2 N/A Transmitter Field Strength (for 27MHz) 15.227 / RSS-310 3.8 Pass Transmitter Field Strength (for 40MHz) 15.229 / RSS-210 A2.7 N/A Transmitter Field Strength, Bandwidth and Timing Requirement (for Remote Control) 15.231(a) / RSS-210 A1.1.1 N/A Transmitter Field Strength, Bandwidth and Timing Requirement (for 433MHz) 15.231(e) / RSS-210 A1.1.5 N/A Transmitter Field Strength and Bandwidth Requirement(for 88-108MHz) 15.239 / RSS-210 A2.8 N/A Transmitter Field Strength and Bandwidth Requirement(for 902- 928MHz or 2.4GHz) 15.249 / RSS-210 A2.9 N/A Transmitter Field Strength and Bandwidth Requirement (for 49MHz) 15.235 / RSS-310 3.9 N/A Receiver / Digital Device Radiated Eissions 15.109 / ICES-003 N/A Digital Device Conducted Emissions 15.107 / ICES-003 N/A Note: 1. The EUT uses a permanently attached antenna which, in accordance to section 15.203, is considered sufficient to comply with the pervisions of this section. 2. Pursuant to FCC part 15 Section 15.215(c), the 20 dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over excepted variations in temperature and supply voltage were considered. INTERTEK TESTING SERVICES Report No.: HK11080263-1 FCC ID: PQN44319TX iii Table of Contents 1.0 General Description........................................................................................................................ 1 1.1 Product Description........................................................................................................................... 1 1.2 Related Submittal(s) Grants .............................................................................................................. 1 1.3 Test Methodology............................................................................................................................. 1 1.4 Test Facility....................................................................................................................................... 1 2.0 System Test Configuration............................................................................................................. 2 2.1 Justification ....................................................................................................................................... 2 2.2 EUT Exercising Software .......................................…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICE Report No: HK11080263-1 FCC ID: PQN44319TX Configuration Photographs Worst-Case Radiated Emissions (Front View) Model: 44319 INTERTEK TESTING SERVICE Report No: HK11080263-1 FCC ID: PQN44319TX Configuration Photographs Worst-Case Radiated Emissions (Rear View) Model: 44319