PQSWAVENET-DUAL-VPDA Wireless Modem attachment for Palm V/Vx

June 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: PQSWAVENET-DUAL-V Exhibit 9 User’s Manual PDA Wireless Modem attachment for Palm V/V x Dualwave V Model: DWV 100D User Manual © Wavenet Technology Pty Ltd ACN 079 965 003 Publication No. xxxx xxxx ( Fourth Draft 25 th May) Published May 2001 This publication is copyright and no part may be reproduced or copied without the prior consent of: Wavenet Technology Pty Ltd. 140 Burswood Rd Burswood Perth WA 6100 Australia Telephone:+61 8 9262 0200 Facsimile:+61 8 9355 5622 E-mail:[email protected] Web Site:www.wavenet.com.au This manual is intended to be used for the operation of Wavenet Technology equipment. Performance figures quoted are typical values and subject to normal manufacturing and service tolerances. Wavenet Technology Pty Ltd reserves the right to alter, without notice, the equipment, software or specification to meet technological advancement. Produced by Wavenet Technology Pty Ltd. This product contains a transmitter approved under the FCC rules: Parts 2 and 90. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesired operation. This device complies with the Industry Canada RSS119. This device complies with the Class B limits for radio noise emissions as set out in the interference- causing equipment standard entitled “Digital Apparatus”, IECS-003 of Industry Canada. Dualwave V User Manual_______________________________________________________Using Your Dualwave V Contents Introduction.....................................................................................................4 Features.......................................................................................................4 Compliance Statement.................................................................................5 Information for Your Safety...........................................................................5 System Requirements..................................................................................8 Checking the Package Contents..................................................................8 Exploring Your Dualwave V..........................................................................9 Getting Started..............................................................................................10 Charging the Dualwave V’s Battery............................................................10 Connecting Your Dualwave V to the PDA..................................................12 Removing the Dualwave V......................................................................12 Installing the Software................................................................................13 Removing the Software...........................................................................14 Setting Your Profile.....................................................................................14 Using Your Dualwave V................................................................................16 Exchanging Data Between Your PDA and Computer.................................16 Setting the Power Save Option...................................................................17 Troubleshooting............................................................................................18 Checking the Connection Status................................................................18 Care & Maintenance.....................................................................................20 Specifications................................................................................................21 Using Your Dualwave V_______________________________________________________Dualwave V User Manual Introduction The Dualwave V is a wireless modem developed for Personal Digital Assistants (PDAs), such as the Palm V/Vx™ and IBM Workpad 3™. It enables access to worldwide DataTAC wireless networks in the USA, Canada, Malaysia, Singapore, Hong Kong, Taiwan and Australia. This technology offers the following unique benefits to the PDA user. • Dualwave V’s unique PUSH technology “wakes up” the PDA and immediately alerts you of a new message. • The serial port provides three additional functions for the PDA user by: -Allowing the use of modem function for transmitting and receiving data to a PC - Exchanging and updating data between PDA and computer. - Allowing the simultaneous charging of the PDA and Modem batteries. Using additional software, the Dualwave V effectively turns your PDA into a wireless window on the web and lets you use your existing e-mail accounts for mail. This manual provides details on how to set up, charge and use the Dualwave V. There is a troubleshooting section to the rear of the manual and a section on the care and maintenance of your new Dualwave V. Specifications are displayed on the last page. Features The Dualwave V has the following features: • Form hugging clip-on modem suitable for Palm V/Vx ™ (and IBM Workpad ® c3) PDAs. • Secure locking mechanism. • May be used independently as a wireless modem for PC/laptop by using additional software. • Roaming capabilities as used in RDLAP system. • Modem is always online using the DataTAC network. • Auto wake up of PDAs from incoming messages. • HotSync ® button for synchronising data between PDA and PC. • Extended battery life (5 days standby, 14 hours communication time). • High sensitivity reception. • Indicator lights shows the status of the network coverage and battery condition. Dualwave V User Manual_______________________________________________________Using Your Dualwave V Compliance Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of …

Text truncated - open the document above for the full version.

June 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: PQSWAVENET-DUAL-V Exhibit 10 Attestation Statements FCC Part 15, Subpart B Class B Certificate of Conformity FCC Part 2 & 90 Statement of Compliance June 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 Certificate of Compliance FCC ID: PQSWAVENET-DUAL-V PRODUCT: PDA Wireless Modem attachment for Palm V/Vx MODEL: DWV 100D MANUFACTURER: Wavenet Technology Pty Ltd We certify that the pertinent tests have been performed on the above-described equipment and that this equipment conforms to the applicable requirements of FCC Parts 2, 15 and 90. See Exhibit 2, Engineering Reports Jayanta (Jay) K. Sarkar Technical Director, Standards and Certification APREL Laboratories

June 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: PQSWAVENET-DUAL-V Table of Contents List of Exhibits Submitted E E X X H H I I B B I I T T 1 1 : : C C O O V V E E R R L L E E T T T T E E R R S S a) Application overview b) Equipment Identification c) Authorization Letter /Agent Designated (Jay Sarkar) d) Request for confidentiality Exhibit 2:Engineering Reports (Test Reports) a) ERP (2.1046) b) Radiated Spurious Emissions (2.1053) c) Bandwidth (2.1049) Modulation Characteristics (2.1047) d) Spurious Emissions at Antenna Terminal (2.1051) e) Frequency Stability (2.1055) Exhibit 3: Operational/Technical Description Exhibit 4: ID Label/Location Exhibit 5:External Photographs of the Equipment Internal Photographs of the equipment Exhibit 6:Block Diagram (Confidential) Exhibit 7: Schematic Diagram (Confidential) Exhibit 8:Parts List (Confidential), Tune–up Procedure Exhibit 9:User’s Manual Exhibit 10:a) Attestation Statement: FCC Part 15 Declaration of Conformance (DoC) certificate b) Attestation Statement: the equipment complies with Part 90 Exhibit 11:RF Exposure Information: SAR Report (Includes Test Set-up Photographs)

June 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: PQSWAVENET-DUAL-V Exhibit 1 a) Application overview b) Equipment c) Authorization Letter /Agent Designated (Jay Sarkar) d) Request for confidentiality June 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 EXHIBIT 1b Equipment Identification FCC ID: PQSWAVENET-DUAL-V MANUFACTURER: Wavenet Technology Pty Ltd PRODUCT: PDA Wireless Modemattachment for Palm V/Vx MODEL: DWV 100D EUT TYPE: Licensed Non-Broadcast Station Transmitter (TNB) TX Frequency: 806-821 MHz MEASURED ERP: 1.86 W

June 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: PQSWAVENET-DUAL-V Exhibit 4 FCC ID Label/Location

June 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: PQSWAVENET-DUAL-V Exhibit 5 Photographs of the Equipment External Photos Internal Photos

June 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: PQSWAVENET-DUAL-V Exhibit 11 RF Exposure Information SAR Report Certification Report on Specific Absorption Rate (SAR) Experimental Analysis Wavenet Technologies Pty Ltd. PDA Wireless Modem Attachment for Palm V/Vx Model DWV 100D Test Date: June 2001 51 Spectrum Way Nepean ON K2R 1E6 Tel: (613) 820-2730 Fax: (613) 820-4161 email: [email protected] This report shall not be reproduced, except in full, without the express written permission of APREL Laboratories WVTB-Palm V Motient cradle-3731 A161-Dualwave V Page 2 of 18 Project #:WVTB-Palm V Motient Cradle-3731 51 Spectrum Way Tel. (613) 820-2730 Nepean, Ontario, K2R 1E6 Fax (613) 820 4161 e-mail: [email protected] © APREL 2000 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories. FCC ID: PQSWAVENET-DUAL-V Applicant: Wavenet Technologies Pty Ltd Equipment: PDA Wireless Modem Attachment for a Palm V/Vx Model: DWV 100D Standard: FCC 96 –326, Guidelines for Evaluating the Environmental Effects of Radio- Frequency Radiation ENGINEERING SUMMARY This report contains the results of the engineering evaluation performed on the DWV 100D Attachment for a Palm V/Vx. The measurements were carried out in accordance with FCC 96- 326. The DWV 100D was evaluated for its maximum power level 1.862 (ERP) with a 7 % duty cycle. The DWV 100D modem is an attachment for a Palm PDA. The device can also be attached to a desktop PC. The DWV 100D was tested at low, middle and high channels for the keyboard up, keyboard down, and right sides for body, hand, and bystander exposure while attached to the PDA only. The maximum 10g SAR (0.63 W/kg) was found to coincide with the peak performance RF output power of channel 2000 (806 MHz) for the Keyboard Down of the device. (The hot spot is located near the base of the antenna). The maximum 1g SAR (0.89 W/kg) was found to coincide with the peak performance RF output power of channel 2000 (806 MHz) for the Keyboard Down of the device. (The hot spot is located near the base of the antenna). Test data and graphs are presented in this report. The DWV 100D was tested at low, middle and high channels for the keyboard up, keyboard down, and right sides for bystander exposure while attached to a desktop PC with and without the PDA. The maximum measured value was found to coincide with the peak performance RF output power of channel 2000 (806 MHz) for the Keyboard Down of the device. At a separation distance of 0 cm from the antenna of the device, the maximum 1g SAR is 0.95 W/kg. Based on the test results and on how the device will be marketed and used, it is certified that the product meets the requirements as set forth in the above specifications, for the RF exposure environment. (The results presented in this report relate only to the sample tested.) Page 3 of 18 Project #:WVTB-Palm V Motient Cradle-3731 51 Spectrum Way Tel. (613) 820-2730 Nepean, Ontario, K2R 1E6 Fax (613) 820 4161 e-mail: [email protected] © APREL 2000 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories. Table of Contents 1. Introduction....................................................................................................................4 2. Applicable Documents...................................................................................................4 3. Device Under Investigation...........................................................................................4 4. Test Equipment..............................................................................................................5 5. Test Methodology..........................................................................................................5 6. Test Results....................................................................................................................6 6.1. Transmitter Characteristics............................................................................................6 6.2. SAR Measurements.......................................................................................................7 7. User’s Hand Exposure...................................................................................................8 8. Body/bystander Exposure.............................................................................................9 9. Bystander Exposure (attached to desktop PC)............................................................10 10. Conclusions..................................................................................................................12 APPENDIX A. Measurement Setup, Tissue Properties and SAR Graphs.............................14 APPENDIX B. Uncertainty Budget........................................................................................16 APPENDIX C. Validation Scan on a Flat Phantom...............................................................17 APPENDIX D. Probe Calibration...........................................................................................18 TABLES AND FIGURES Table 1. Sampled RF Power.....................................................................................................6 Table 2. SAR Measurements.....................................................................................................8 Figure 1. PDA With DUI.........................................................................................................11 Figure 2. DUI With Desktop PC.............................................................................................12 Figure 3. Setup.........................................................................................................................14 Table 3. Dielectric Properties of the Simulated Muscle Tissue at 815 MHz...........................14 Figure 4. Contour Plot of the Area Scan 2.5mm Above Ph…

Text truncated - open the document above for the full version.

June 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: PQSWAVENET-DUAL-V Exhibit 2a Engineering Report on ERP (2.1046) Assessment of Compliance for Measurement of Effective Radiated Power (ERP) in accordance with the FCC Rules & Regulations Part 2.1046 and 90 PDA Wireless Modem attachment for Palm V/V x DWV 100D Wavenet Technologies Pty Ltd. 51 Spectrum Way Nepean ON K2R 1E6 Tel: (613) 820-2730 Fax: (613) 820-4161 email: [email protected] June 2001 APREL Project No.:WVTB-Dual Wave V-3279  June 2001 Page 3 APREL Project No WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 FCC ID:PQSWAVENET-DUAL-V Applicant:Wavenet Technologies Pty Ltd. Equipment:PDA Wireless Modem attachment for Palm V/V x Model:DWV 100D Standard:FCC Rules and Regulations Part 2.1046 and 90 ENGINEERING SUMMARY This report contains the results of the effective radiated power (ERP) measurement performed on a Wavenet PDA Wireless Modem attachment for Palm V/V x , model DWV100D The measurements were carried out in accordance with the FCC Rules and Regulations Part 2.1046 and 90. The product was evaluated for ERP when it was set at the maximum power level. Wavenet DWV 100D was tested for ERP at high, middle, and low frequencies with the maximum ERP obtained at frequency 806.00 MHz. The test data is presented in this report under the section: Test Results. The measured ERP is 1.862 W. The PDA Wireless Modem is an attachment for a Palm PDA and it can also be attached to a PC. The DWV 100D was evaluated in three configurations: 1. PDA Wireless Modem attached to Palm V, 2. PDA Wireless Modem attached to Palm V and connected to PC, 3. PDA Wireless Modem connected to PC. The highest values of ERP were obtained in configuration 1 (Palm V and PDA Wireless Modem attached together) placed in vertical position. (The results presented in this report relate only to the sample tested.)  June 2001 Page 4 APREL Project No WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 Summary of the Results Test DescriptionPage No. Test Set-up Figure No. Results Summary RF Power Output as Radiated Ref. Paragraph 2.1046 and 9081 Passed  June 2001 Page 5 APREL Project No WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 INTRODUCTION General This report describes the results of the effective radiated power (ERP) measurement conducted on a Wavenet Technologies PDA Wireless Modem, model DWV 100D. Test Facility The tests were performed for Wavenet Technologies Pty Ltd. by APREL Laboratories at APREL’s EMI facility located in Nepean, Ontario, Canada. The laboratory operates an (3m and 10m) Open Area Test Site (OATS). The measurement facility is calibrated in accordance with ANSI C63.4- 1992. A description of the measurement facility in accordance with the radiated and AC line conducted test site criteria per ANSI C63.4-1992 is on file with the Federal Communications Commission and is in compliance with the requirements of Section 2.948 of the Commissions rules and regulations. APREL’s registration number is: 90416 APREL is accredited by Standard Council of Canada. APREL is also accredited by Industry Canada and recognised by the Federal Communications Commissions (FCC). Standard The evaluation and analysis were conducted in accordance with FCC Rules and Regulations Parts 2.1046 and the appropriate limits (90). Test Equipment The test equipment used during the evaluation is listed in Appendix A with calibration due dates. Environmental Conditions Measurements were conducted in open area test site. - Temperature:25 °C ± 2 - Relative Humidity:30 - 50 % - Air Pressure:101 kPa ± 3  June 2001 Page 6 APREL Project No WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 FCC SUBMISSION INFORMATION FCC ID:PQSWAVENET-DUAL-V Equipment (type):PDA Wireless Modem attachment for Palm V/V x As Marketed Model:DWV 100D For:Certification Applicant:Wavenet Technologies Pty Ltd. 140 Burswood Rd Burswood, Perth, WA 6100 AUSTRALIA Manufacturer: Wavenet Technologies Pty Ltd. 140 Burswood Rd Burswood, Perth, WA 6100 AUSTRALIA Evaluated by:APREL Laboratories 51 Spectrum Way Nepean, Ontario Canada K2R 1E6  June 2001 Page 7 APREL Project No WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 MANUFACTURER’S DATA FCC ID No:PQSWAVENET-DUAL-V Equipment Type: PDA Wireless Modem attachment for Palm V/V x Model:DWV 100D Reference:FCC Rules and Regulations Parts 2 and Part 90 Manufacturer:Wavenet Technologies Pty Ltd Power Source:3.6 (nominal) VDC, Lithium Battery Development Stage of Unit:Production GENERAL SPECIFICATIONS 1.Frequency Range:806.00 to 821.00 MHz (Transmitter) 2. Measured ERP1.862 (32.7 dBm) 3.Emission Designators (See 47 CFR § 2.201 and §2.202):20K0F1D 4. Antenna Impedance:50 Ohms  June 2001 Page 8 APREL Project No WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 Test:RF Power Output as Radiated (ERP) Ref.:FCC Part 2 paragraph 2.1046 and 90 Criteria:N/A Set-up:See Figure No. 1. Equipment:See Appendix A. Methodology:RF Power Measurement by Substitution Method : Test site: The radiated RF power measurement was taken at APREL Laboratory’s open…

Text truncated - open the document above for the full version.

June 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: PQSWAVENET-DUAL-V Exhibit 2b Engineering Report on Radiated Spurious Emissions (2.1053) Assessment of Compliance for Measurement of Field Strength of Spurious Radiation in accordance with the FCC Rules & Regulations Part 2.1053 and 90 PDA Wireless Modem attachment for Palm V/V x DWV 100D Wavenet Technologies Pty Ltd. 51 Spectrum Way Nepean ON K2R 1E6 Tel: (613) 820-2730 Fax: (613) 820-4161 email: [email protected] June 2001 APREL Project No.:WVTB-Dual Wave V-3279 June 2001 Page 3 APREL Project No: WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 FCC ID:PQSWAVENET-DUAL-V Applicant:Wavenet Technologies Pty Ltd. Equipment:PDA Wireless Modem attachment for Palm V/Vx Model:DWV 100D Standard:FCC Rules and Regulations Part 2.1053 and 90 ENGINEERING SUMMARY This report contains the results of Field Strength of Spurious Radiation measurement performed on a Wavenet PDA Wireless Modem attachment for Palm V/Vx, model DWV 100D in accordance with the FCC Rules and Regulations Part 2.1053 and 90. The measurements were carried out using direct method and substitution method both as radiated. The product was evaluated for spurious radiation when it was set at the maximum power level. The PDA Wireless Modem is an attachment for a Palm PDA and it can also be attached to a PC. The DWV 100D was evaluated in three configurations: 1. PDA Wireless Modem attached to Palm V 2. PDA Wireless Modem attached to Palm V and connected to PC 3. PDA Wireless Modem (cradle only) connected to PC. The highest values of Spurious Emissions were obtained in configuration 1 (PDA Wireless Modem attached to Palm V) placed in vertical position. As such, test data using both methods (direct and substitution) for configuration 1 only is presented. The test data for configurations 2 and 3 are given using only substitution method. (The results presented in this report relate only to the sample tested.) June 2001 Page 4 APREL Project No: WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 Summary of the Results Test DescriptionPage No. Test Set-up Figure No. Results Summary Field Strength of Spurious Radiation Ref. Paragraph 2.1053 and 9081 Passed June 2001 Page 5 APREL Project No: WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 INTRODUCTION General This report describes the results of the Field Strength of Spurious Radiation measurement conducted on a Wavenet PDA Wireless Modem attachment for Palm V/Vx, model DWV 100D. Test Facility The tests were performed for Wavenet Technologies Pty Ltd. by APREL Laboratories at APREL’s EMI facility located in Nepean, Ontario, Canada. The laboratory operates an (3m and 10m) Open Area Test Site (OATS). The measurement facility is calibrated in accordance with ANSI C63.4- 1992. A description of the measurement facility in accordance with the radiated and AC line conducted test site criteria per ANSI C63.4-1992 is on file with the Federal Communications Commission and is in compliance with the requirements of Section 2.948 of the Commissions rules and regulations. APREL’s registration number is 90416 APREL is accredited by Standard Council of Canada. APREL is also accredited by Industry Canada and recognised by the Federal Communications Commissions (FCC). Standard The evaluation and analysis were conducted in accordance with FCC Rules and Regulations Parts 2.1053 and the appropriate limits (90). Test Equipment The test equipment used during the evaluation is listed in Appendix A with calibration due dates. Environmental Conditions Measurements were conducted in open area test site. - Temperature: 24 °C ± 2 - Relative Humidity:30 - 50 % - Air Pressure:101 kPa ± 3 June 2001 Page 6 APREL Project No: WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 FCC SUBMISSION INFORMATION FCC ID:PQSWAVENET-DUAL-V Equipment type:PDA Wireless Modem attachment for Palm V/Vx Model:DWV 100D For:Certification Applicant:Wavenet Technologies Pty Ltd. 140 Burswood Rd Burswood, Perth, WA 6100 AUSTRALIA Manufacturer: Wavenet Technologies Pty Ltd. 140 Burswood Rd Burswood, Perth, WA 6100 AUSTRALIA Evaluated by:APREL Laboratories 51 Spectrum Way Nepean, Ontario Canada K2R 1E6 June 2001 Page 7 APREL Project No: WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 MANUFACTURER’S DATA FCC ID:PQSWAVENET-DUAL-V Equipment Type: PDA Wireless Modem attachment for Palm V/Vx Model:DWV 100D Reference:FCC Rules and Regulations Parts 2 and Part 90 Manufacturer:Wavenet Technologies Pty Ltd Power Source:3.6 (nominal) VDC Battery, Lithium-ion Development Stage of Unit:Production GENERAL SPECIFICATIONS 1.Frequency Range:806.00 to 821.00 MHz (Transmitter) 2. Output Power:1.862 W (ERP) 3.Emission Designators (See 47 CFR § 2.201 and §2.202):20K0F1D 4. Antenna Impedance:50 Ω June 2001 Page 8 APREL Project No: WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 Test:Field Strength of Spurious Radiation Ref:FCC Parts 2.1053 and 90.210 Criteria:Emission Mask G: The permitted maximum level of spurious emission is 43 + 10 log (P) dB below the unmodulated carr…

Text truncated - open the document above for the full version.

June 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: PQSWAVENET-DUAL-V Exhibit 2c Engineering Report on Bandwidth (2.1049) Modulation Characteristics (2.1047) Assessment of Compliance for Measurement of Modulation Characteristic/ Occupied Bandwidth in accordance with the FCC Rules & Regulations Part 2.1047/49 and 90 PDA Wireless Modem attachment for Palm V/V x DWV 100D Wavenet Technologies Pty Ltd. 51 Spectrum Way Nepean ON K2R 1E6 Tel: (613) 820-2730 Fax: (613) 820-4161 email: [email protected] June 2001 APREL Project No.:WVTB-Dual Wave V -3279  June 2001 Page 3 APREL Project No WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories COCOCONSULTING * Research * Training * Certification Testing Since 1981 FCC ID:PQSWAVENET-DUAL-V Applicant:Wavenet Technologies Pty Ltd. Equipment:PDA Wireless Modem attachment for Palm V/V X Model:DWV 100D Standard:FCC Rules and Regulations Part 2.1047/49 and 90 ENGINEERING SUMMARY This report contains the results of the Occupied Bandwidth/Bandwidth Limitation measurement performed on a Wavenet PDA Wireless Modem attachment for Palm V/V x model DWV 100D. The measurements were carried out in accordance with the FCC Rules and Regulations Part 2.1049. The product was evaluated for bandwidth when it was set at the maximum power level. The PDA Wireless Modem is an attachment for a Palm PDA and it can also be attached to a PC. However, the Bandwidth Limitation was carried out only on PDA Wireless Modem attached to Palm V, as bandwidth does not change due to different configurations. Modulation Characteristics (FCC Rule PART 2.1047): This test is not applicable, as the device is not capable of voice transmission. Limiting of Modulation: The Modulation levels are fixed for digital modulation levels only and are digitally generated. The Modulation deviation is set during manufacture to the standard RD LAP 19.2 kbps 4 level FSK modulation and MDC 4.8 kbps 2 level FSK. This format is digital non-voice data only, continuous frequency, continuous phase, and frequency shift keying, narrow band frequency modulation. (The results presented in this report relate only to the sample tested.)  June 2001 Page 4 APREL Project No WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories COCOCONSULTING * Research * Training * Certification Testing Since 1981 Summary of the Results Test DescriptionPage No. Test Set-up Figure No. Results Summary Bandwidth/bandwidth Limitation Ref. Paragraph 2.1049 and 9081 Passed  June 2001 Page 5 APREL Project No WVTB-Dual Wave V-3729 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories COCOCONSULTING * Research * Training * Certification Testing Since 1981 INTRODUCTION General This report describes the results of the occupied bandwidth measurement cond…

Text truncated - open the document above for the full version.