PQTDORM38315 MHz Keyfob Transmitter

ALL KEY FOBS MUST BE PRESENT AND REPROGRAMMED WHEN PROGRAMMING NEW FOBS Programming Instructions: Key blade needs to be cut and programmed by a certified locksmith. FCC WARNING Statement 15.19(a)(3): This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Dorman Products Inc. could void the user’s authority to operate the equipment. FCC Part 15.21: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. IC WARNING FVIN 6399395IC The term IC before the Certification/Registration number only signifies that the Industry Canada technical specifications were met. This device comp lies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device mus t accept any interference Including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. Cet appareil est conforme aux RSSs exempts de licence d'Industrie Canada. Le fonctionnement est Suivant deux conditions: 1) Cet appareil ne doit pas causer d'interférences; Et (2) Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent Fonctionnement du dispositif

Date: 4/24/2020 To: Federal Communications Commission Authorization and Evaluation Division From: Joseph Braun, Senior Vice President, General Counsel Subject: Agent Authorization for certification of FCC ID: PQTDORM38 Dear Sir or Madam: Dorman Products hereby appoints Richard Reitz of Retlif Testing Laboratories to act as our agent in the matter of FCC filings for the certification of FCC ID: PQTDORM38 Dorman Products further attest that no party to the application is subject to denial of federal benefits pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 USA 853(a). Sincerely, Joseph Braun Senior Vice President, General Counsel Dorman Products, Inc.

NEW PRODUCTS. NEW SOLUTIONS. NEW OPPORTUNITIES. 3400 East Walnut Street • Colmar, PA 18915-1800 • Customer Service: 1-800-523-2492 • Fax: 859-567-7010 Dear Sir or Madam: The application for FCC ID: PQTDORM38 will cover 3 unique part numbers. The only differences are in the plastic case containing the PCB. Each PCB is equipped with multiple solder pads to accommodate the variety of button configurations. MODEL DESCRIPTION Buttons 99395 KEYLESS ENTRY REMOTE 3 99396 KEYLESS ENTRY REMOTE 4 99397 KEYLESS ENTRY REMOTE 6 Sincerely, Joseph Braun Senior Vice President, General Counsel Dorman Products, Inc.

Rev 11/20/07 Federal Communications Commission Authorization and Evaluation Division Subject: Confidentiality Request regarding application for certification of FCC ID: PQTDORM38 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Operational Description PQTDORM38 OpDes.pdf Schematic PQTDORM38 Schem.pdf Part List PQTDORM38 PartsLst.pdf Block Diagram PQTDORM38 BlkDia.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name None None Sincerely, Joseph Braun Senior Vice President, General Counsel Dorman Products, Inc.

External Photos PQTDORM38 Front Rear Top Bottom External Photos PQTDORM38 Side 1 Side 2

Label Location PQTDORM38 Note: Label Location is identical on all models listed for PQTDORM38. Label text will be laser etched on to key fob.

DORMAN PRODUCTS Model: 99397 102817 YYDDD FCC ID: PQTDORM38 IC: 10735A-DORM38 BATT CR2032

FCC Part 15, Subpart C, Section 15.231 Industry Canada, RSS-210 and RSS-GEN Test Report On Keyfob Transmitter FCC ID: PQTDORM38 IC: 10735A-DORM38 Customer Name: Dorman Products, Inc. Customer P.O: 4200007133 Date of Report: May 1, 2020 Test Report No: R-2844P-1 and R-2844P-2 Test Start Date: February 1, 2018 Test Finish Date: April 29, 2020 Test Technician: M. Nowak Test Engineer:: A. Warwick Approved By: D. Rybicki Report Prepared By: P. Harris Our letters, procedures and reports are for the exclusive use of the customer to whom they are addressed and their communication or the use of the name of Retlif Testing Laboratories must receive our prior written approval. Our letters, procedures and reports apply only to the sample tested and are not necessarily indicative of the qualities of apparently identical or similar products. The letters, procedures and reports and the name of Retlif Testing Laboratories or insignia are not to be used under any circumstances in advertising to the general public. This test report shall not be reproduced, except in full, without the written approval of Retlif Testing Laboratories. Report No. R-2844P-1/2 Page 2 of 33 Retlif Testing Laboratories R Table of Contents Certification and Signatures .................................................................................................. 3 Revision History .................................................................................................................... 4 Requirements and Test Results ............................................................................................ 8 General Requirements FCC and IC .................................................................................... 13 Open Area Test Site ........................................................................................................... 14 Equipment Lists .................................................................................................................. 15 Test Data ............................................................................................................................ 16 Report No. R-2844P-1/2 Page 3 of 33 Retlif Testing Laboratories R Certification and Signatures We certify that this report is a true representation of the results obtained from the tests of the equipment stated. We further certify that the measurements shown in this report were made in accordance with the procedures indicated and vouch for the qualifications of all Retlif Testing Laboratories personnel taking them. Arik L. Warwick EMC Test Engineer David M. Rybicki Laboratory Supervisor Non-Warranty Provision The testing services have been performed, findings obtained and reports prepared in accordance with generally accepted laboratory principles and practices. This warranty is in lieu of all others, either expressed or implied. Non-Endorsement This test report contains only findings and results arrived at after employing the specific test procedures and standards listed herein. It is not intended to constitute a recommendation, endorsement or certification of the product or material tested. This report must not be used by the client to claim product endorsement by ANSI National Accreditation Board (ANAB). Report No. R-2844P-1/2 Page 4 of 33 Retlif Testing Laboratories R Revision History Revisions to this document are listed below; the latest revised document supersedes all previous issues of this document. Revision Date Pages Affected - May 1, 2020 Original Release Report No. R-2844P-1/2 Page 5 of 33 Retlif Testing Laboratories R Technical Information Report Number: R-2844P-1 and R-2844P-2 Customer: Dorman Products, Inc. Address: 3400 East Walnut Street Colmar, PA 18915 Manufacturer: Dorman Products, Inc. Manufacturer Address: 3400 East Walnut Street Colmar, PA 18915 Test Sample: Keyfob Transmitter Model Numbers: 99395, 99396, 99397 FCC ID: PQTDORM38 IC: 10735A-DORM38 Type: Security / Remote Control Transmitter Power Requirements: 3 VDC Derived from a CR2032 Battery Frequency of Operation: 315 MHz Equipment Class: DSC Equipment Use: Portable, <2.5 cm Test Specification: FCC Rules and Regulations Part 15, Subpart C, Section 15.231 Radio Standards Specification, RSS-210, Issue 9, August, 2016 Test Procedure: ANSI C63.10:2013 RSS-GEN, Issue 5, April 2018 Test Site: ANSI C63.4:2014 Test Facility: Retlif Testing Laboratories 3131 Detwiler Road Harleysville, PA 19438 FCC Accreditation Designation Number: US2321 ISED Test Site Registration Number: 2047B Report No. R-2844P-1/2 Page 6 of 33 Retlif Testing Laboratories R Tests Performed The test methods performed on the Keyfob Transmitter are shown below: FCC Part 15, Subpart C Industry Canada RSS-210 Industry Canada RSS-GEN Test Method Test Results 15.231(b) A1.1.2(1) N/A Field Strength of Emissions Complied 15.231(b)(2) A1.1.2(2) 4.5 Duty Cycle Determination Complied 15.231(b)(3) A1.1.2(3) N/A Field Strength of Spurious Emissions Complied 15.231(c) A1.1.3 N/A Bandwidth of Emission Complied All test methods listed above are included in Retlif Testing Laboratories ANSI National Accreditation Board (ANAB), ISO/IEC 17025 Scope of Accreditation. Report No. R-2844P-1/2 Page 7 of 33 Retlif Testing Laboratories R General Test Requirements 1. The measurement procedures of ANSI C63.10:2013 were utilized as specified in FCC Part 15, Subpart C, Section 15.31(a)(3) and IC RSS-GEN Section 4.1. 2. All radiated emissions measurements were performed on an Open Area Test Site (OATS), listed with the FCC and IC, in accordance with FCC Section 15.31(d) and IC Section 4.2. 3. The level of the fundamental field strength was recorded with a new battery installed in the EUT, in accordance with FCC Section 15.231(e) and IC Section 4.3(e). 4. All measurements were performed at the specified 3 meter test distance as required by FCC Section 15.31(f) and IC Section 7.25. 5. The EUT was rotated throughout 360 degrees for all radiated emissions measurements as specified in FCC Section 1…

Text truncated - open the document above for the full version.

Page 1 of 13 Dorman Products, Inc. Test Setup Photographs FCC ID: PQTDORM38 IC: 10735A-DORM38 Page 2 of 13 Field Strength of Emissions Test Setup Photographs Test Setup, X Axis, Below 1 GHz Test Setup, X Axis, Above 1 GHz Page 3 of 13 Field Strength of Emissions Test Setup Photographs Test Setup, Y Axis, Below 1 GHz Test Setup, Y Axis, Above 1 GHz Page 4 of 13 Field Strength of Emissions Test Setup Photographs Test Setup, Z Axis, Below 1 GHz Test Setup, Z Axis, Above 1 GHz Page 5 of 13 Field Strength of Emissions Test Setup Photographs Horizontal Antenna Polarization, Below 1 GHz Vertical Antenna Polarization, Below 1 GHz Page 6 of 13 Field Strength of Emissions Test Setup Photographs Horizontal Antenna Polarization, Above 1 GHz Vertical Antenna Polarization, Above 1 GHz Page 7 of 13 Field Strength of Spurious Emissions Test Setup Photographs EUT Configuration Page 8 of 13 Field Strength of Spurious Emissions Test Setup Photographs Parallel, 9 kHz to 30 MHz Perpendicular, 9 kHz to 30 MHz Page 9 of 13 Field Strength of Spurious Emissions Test Setup Photographs Horizontal Antenna Polarization, 30 to 200 MHz Vertical Antenna Polarization, 30 to 200 MHz Page 10 of 13 Field Strength of Spurious Emissions Test Setup Photographs Horizontal Antenna Polarization, 200 MHz to 1 GHz Vertical Antenna Polarization, 200 MHz to 1 GHz Page 11 of 13 Duty Cycle Determination Test Setup Photograph Test Setup Page 12 of 13 Occupied Bandwidth of Emissions Test Setup Photograph Test Setup Page 13 of 13 99% Occupied Bandwidth Test Setup Photograph Test Setup