PRDPRINTER002Bluetooth Stopwatch Presenter with Laser Pointer

Page  User’s Manual Bluetooth Stopwatch Presenter with Laser Pointer Page  Regulatory Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Certification This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. • • Page 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Notice: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Extension cables are not recommended, if used, they must be shielded in order to comply with the emission limits. IC Certification The term “IC” before the certification/registration number only signifies that the Industry Canada technical specifications were met. Declaration of conformity Hereby, SMK-LINK Electronics Corporation, declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. All trademarks and registered trademarks mentioned in this document are the property of their respective owners. Features and specifications are subject to change without notice. © 2008 SMK-LINK Electronics, Inc. • • Page  System Requirements Hardware: Bluetooth-enabled system (via built-in Bluetooth capability or external Bluetooth adapter) Operating System: Windows 2000, XP or Vista Macintosh OS X or above (F5 SlideShow and Alt-Tab Application Switch not supported) Package Contents Bluetooth stopwatch presenter 2 x AAA batteries User’s manual Carrying case Installing the Rechargeable Batteries (Supplied) • • • • Sliding the battery cover off Insert batteries to the correct polarities Page  Open the battery compartment by pressing down the cover latch and sliding the door off the presenter. Insert the two supplied AAA batteries (included in the package) to the battery slots. Make sure the positive (+) and negative (-) ends of the batteries match the polarity markings inside the battery compartment. Close the battery cover back into position Power on the presenter by sliding the on/off switch to ON position. • • • • On/Off Power switch on the presenter Page  Connecting with Your Bluetooth Computer Before you can use Bluetooth devices for the first time you must connect your devices through a standard discovery and pairing process. Microsoft Windows Bluetooth Stack Make sure your computer’s Bluetooth radio is turned on. Make sure your Bluetooth presenter is turned on (check the on/off switch located on the left-hand side of the presenter. Right click the Bluetooth icon located on your Desktop or the System Tray, select Add a Bluetooth Device. 1. 2. 3. Page  A list of connected Bluetooth devices is presented on the screen. Select Add...; click OK. At this point, the presenter must be placed in discovery mode. Press the Connect button located above the battery cover at the back of the presenter. The LED 4. 5. Page  light on the top of the presenter will flash, indicating the presenter is in discovery mode ready to be connected to the computer. Check My device is setup and ready to be found and click Next. This must be performed within 20 seconds to avoid expiration of the discovery signal. 6. Connect Button Page  The Interlink Bluetooth Presenter will be discovered and listed on the screen. Highlight the name of the device and click Next. 7. Page 0 The Wizard will ask you whether you like to add a passkey. Select Don’t use a passkey as this product is not a keyboard product and does not support passkey. Click Next. Click Finish on the Wizard to complete the process. 8. 9. Page  The Found New Hardware Wizard appears and the OS will install the driver automatically. No other steps are necessary. The Bluetooth icon will turn to green. Your Bluetooth Stopwatch Presenter is ready to use. Macintosh Bluetooth Software Make sure your computer’s Bluetooth radio is turned on. 10. 11. 1. Page  Make sure your presenter is turned on (check the on/off switch located on the left-hand side of the presenter.) Click the Bluetooth icon located on your desktop or in the system bar. Or, click the Apple icon and click System Preferences, then click on the Bluetooth icon. Select Turn Bluetooth On to enable Bluetooth for your Macintosh computer if it’s not already on. 2. 3. 4. 5. Page  Select Set Up New Device. Bluetooth Setup Assistant screen will show up. Click Continue. At this point, the presenter must be placed in discovery mode. Press the Connect 6. 7. Page  button located above the battery cover on the back of the presenter. The LED light on the top of the presenter will flash, indicating the presenter is in discovery mode ready to be connected to the computer. Connect Button The screen will ask you for the device type. Select Mouse from the device list and click Continue. 8. Page  The computer will search for B…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

MODEL NAME: PR3 FCC ID:PRDPRINTER002

Label位置

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3

FCC ID: PRDPRINTER002 Report No.: RF970326L02 Operational Description The transmitter of the EUT (Bluetooth Stopwatch Presenter with Laser Pointer) is powered by battery. The antenna is printed antenna without antenna connector. For more detailed instruction, please take a look at the user’s manual. This device is a Frequency Hopping device with 79 hopping frequencies.

FCC ID: PRDPRINTER002 Report No: SA970326L02 1 RF EXPOSURE REPORT REPORT NO.: SA970326L02 MODEL NO.: PR3 SEIRES NO.: VP4570 ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: Acrox Technologies Co., Ltd ADDRESS: 8F, No. 437, Rui Guang RD., Nei Hu Dist., Taipei 114, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. FCC ID: PRDPRINTER002 Report No: SA970326L02 2 No evaluation required if power is below this threshold: F(GHz) mW Low 2.402 High 2.480 24.580 Maximum measured transmitter power: Pout (dBm) Pout (mW) Conducted Power 0.190 1.045 EIRP Power -3.55 0.442 *Note: The antenna is printed antenna with -3.74dBi gain Threshold for no SAR evaluation is 24.580mW Transmitter power is 0.442mW Conclusion: No SAR evaluation required since Transmitter Pout is below FCC threshold

Report No.: RF970326L02 1 Report Format Version 2.1.0 FCC TEST REPORT REPORT NO.: RF970326L02 MODEL NO.: PR3 SERIES NO.: VP4570 RECEIVED: Mar. 28, 2008 TESTED: Apr. 07 ~ Apr. 10, 2008 ISSUED: Apr. 14, 2008 APPLICANT: Acrox Technologies Co., Ltd ADDRESS: 8F, No. 437, Rui Guang RD., Nei Hu Dist., Taipei 114, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 43 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF, A2LA or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF970326L02 2 Report Format Version 2.1.0 Table of Contents 1. CERTIFICATION.......................................................................................................4 2. SUMMARY OF TEST RESULTS ..............................................................................5 2.1 MEASUREMENT UNCERTAINTY ...........................................................................5 3. GENERAL INFORMATION .......................................................................................6 3.1 GENERAL DESCRIPTION OF EUT.........................................................................6 3.2 DESCRIPTION OF TEST MODES...........................................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ...................................................... 7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................... 8 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................10 3.4 DESCRIPTION OF SUPPORT UNITS ...................................................................10 4. TEST TYPES AND RESULTS ................................................................................ 11 4.1 RADIATED EMISSION MEASUREMENT .............................................................. 11 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT............................................ 11 4.1.2 TEST INSTRUMENTS ........................................................................................... 12 4.1.3 TEST PROCEDURES ............................................................................................ 13 4.1.4 DEVIATION FROM TEST STANDARD .................................................................. 13 4.1.5 TEST SETUP ......................................................................................................... 14 4.1.6 EUT OPERATING CONDITIONS ........................................................................... 14 4.1.7 TEST RESULTS ..................................................................................................... 15 4.2 CONDUCTED EMISSION MEASUREMENT .........................................................19 4.3 NUMBER OF HOPPING FREQUENCY USED ......................................................19 4.3.1 LIMIT OF HOPPING FREQUENCY USED ............................................................ 19 4.3.2 TEST INSTRUMENTS ........................................................................................... 19 4.3.3 TEST PROCEDURES ............................................................................................ 19 4.3.4 DEVIATION FROM TEST STANDARD .................................................................. 20 4.3.5 TEST SETUP ......................................................................................................... 20 4.3.6 TEST RESULTS ..................................................................................................... 20 4.4 DWELL TIME ON EACH CHANNEL ......................................................................22 4.4.1 LIMIT OF DWELL TIME USED............................................................................... 22 4.4.2 TEST INSTRUMENTS ........................................................................................... 22 4.4.3 TEST PROCEDURES ............................................................................................ 22 4.4.4 DEVIATION FROM TEST STANDARD .................................................................. 22 4.4.5 TEST SETUP ......................................................................................................... 23 4.4.6 TEST RESULTS ..................................................................................................... 23 4.5 CHANNEL BANDWIDTH........................................................................................25 Report No.: RF970326L02 3 Report Format Version 2.1.0 4.5.1 LIMITS OF CHANNEL BANDWIDTH ..................................................................... 25 4.5.2 TEST INSTRUMENTS ........................................................................................... 25 4.5.3 TEST PROCEDURE .............................................................................................. 25 4.5.4 DEVIATION FROM TEST STANDARD .................................................................. 25 4.5.5 TEST SETUP ......................................................................................................... 26 4.5.6 EUT OPERATING CONDITION ............................................................................. 26 4.5.7 TEST RESULTS ..................................................................................................... 26 4.6 HOPPING CHANNEL SEPARATION .....................................................................29 4.6.1 LIMIT OF HOPPING CHANNEL SEPARATION ..................................................... 29 4.6.2 TEST INSTRUMENTS ..........................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST