PRDRX022.4GHz Receiver

2.4GHz Wireless Optical Ergo Mouse w/Nano Receiver USER'S GUIDE Ver.:1.00 CAUTION: To use this product properly, please read the user's guide before installing. 1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. French translation: Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. 2 Functional Introduction Forward Press this button to view the next page in your Internet browser. Backward Press this button to view the previous page in your Internet browser. Installing the batteries Step 1: Take the battery cover off. Step 2: Insert the batteries as shown inside the battery compartment. Step 3: Replace the cover. Step 4: Turn on power switch Left button Right button Battery Cover Scrolling Wheel Connect Button ON/OFF Switch Nano Receiver LED Indicator Backward Forward 3 **Warning: *Please insert the batteries with the correct position according to the instruction labeled in the mouse. Battery warning statement: Do not mix old and new batteries Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries. Setup the Connection between the Receiver and the Mouse 1. Plug the Nano receiver into the USB port of your computer. AAA Battery 1’st 2’nd 4 2. Insert the batteries into the mouse, then follow the steps below. 3. If the mouse is not working, please put it into pairing mode or check the batteries power status. 4. Pairing: Re-plug the receiver into the USB port of your computer, then press the connect button on the mouse. If the mouse does not work after 10 seconds, pair them again. (The receiver has auto pairing function). 5. The LED indicator on mouse flashes steadily when it is in pairing mode and stops blinking when it is successfully paired with the receiver. 6. When the batteries of the mouse is low, the Low Power indicator will start to blink. LED Indicator *Mouse Indicator Red LED Blinks for 10 sec. Low Battery Warning Red LED is on for 10 sec. Power ON Green LED Blinking Pairing (LED OFF when paired or failed after 10 sec.)

Page 1 CONSTRUCTION PHOTOS OF EUT

Model: MRN FCC ID: PRDRX02 IC: 6180A-MRN 1.5mm 1.5mm 居中 1:1图

Page 2 Page 3

FCC ID: PRDRX02 Report No.: RF110318C06 Operational Description This device is a 2.4GHz Receiver. The transmitter of the EUT is powered by 5Vdc from host equipment. The antenna is printed antenna. The other instruction, please have a look at the users manual.

Report No.: RF110318C06 1 Report Format Version 4.0.0 FCC TEST REPORT REPORT NO. : RF110318C06 MODEL NO. : MRN FCC ID: PRDRX02 RECEIVED : Mar. 18, 2011 TESTED : Mar. 22 ~ Mar. 24, 2011 ISSUED : Mar. 30, 2011 APPLICANT : Acrox Technologies Co., Ltd ADDRESS : 4F., No. 89, Minshan St., Neihu Dist., Taipei City 114, Taiwan, R.O.C. ISSUED BY : Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS : No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION : No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 33 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. Report No.: RF110318C06 2 Report Format Version 4.0.0 Table of Contents RELEASE CONTROL RECORD.............................................................................................4 1. CERTIFICATION.........................................................................................................5 2. SUMMARY OF TEST RESULTS.................................................................................6 2.1 MEASUREMENT UNCERTAINTY...............................................................................6 3. GENERAL INFORMATION..........................................................................................7 3.1 GENERAL DESCRIPTION OF EUT............................................................................7 3.2 DESCRIPTION OF TEST MODES..............................................................................8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST..........................................................9 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL.............................10 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS............................................12 3.4 DESCRIPTION OF SUPPORT UNITS.......................................................................12 4. TEST TYPES AND RESULTS...................................................................................13 4.1 RADIATED EMISSION MEASUREMENT..................................................................13 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT................................................13 4.1.2 TEST INSTRUMENTS...............................................................................................14 4.1.3 TEST PROCEDURES...............................................................................................15 4.1.4 DEVIATION FROM TEST STANDARD......................................................................15 4.1.5 TEST SETUP............................................................................................................16 4.1.6 EUT OPERATING CONDITIONS..............................................................................16 4.1.7 TEST RESULTS........................................................................................................17 4.2 CONDUCTED EMISSION MEASUREMENT.............................................................23 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT...........................................23 4.2.2 TEST INSTRUMENTS...............................................................................................23 4.2.3 TEST PROCEDURES...............................................................................................24 4.2.4 DEVIATION FROM TEST STANDARD......................................................................24 4.2.5 TEST SETUP............................................................................................................25 4.2.6 EUT OPERATING CONDITIONS..............................................................................25 4.2.7 TEST RESULTS........................................................................................................26 4.3 BAND EDGES MEASUREMENT...............................................................................28 4.3.1 LIMITS OF BAND EDGES MEASUREMENT............................................................28 4.3.2 TEST INSTRUMENTS...............................................................................................28 4.3.3 TEST PROCEDURE..................................................................................................28 4.3.4 DEVIATION FROM TEST STANDARD......................................................................28 4.3.5 EUT OPERATING CONDITION.................................................................................28 Report No.: RF110318C06 3 Report Format Version 4.0.0 4.3.6 TEST RESULTS........................................................................................................29 5. PHOTOGRAPHS OF THE TEST CONFIGURATION.................................................31 6. INFORMATION ON THE TESTING LABORATORIES...............................................32 7. APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB.............................................................................................33 Report No.: RF110318C06 4 Report Format Version 4.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release N/A Mar. 30, 2011 Report No.: RF110318C06 5 Report Format Version 4.0.0 1. CERTIFICATION PRODUCT: 2.4GHz Receiver MODEL NO.: MRN BRAND: HP APPLICANT: Acrox Technologies Co., Ltd TESTED: Mar. 22 ~ Mar. 24, 2011 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 15, Subpart C (Section 15.249) ANSI C63.4-2003 ANSI C63.10-2009 The above equipment (Model: MRN) have been tested by Bu…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 3 RADIATED EMISSION TEST 4