
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
IEEE 802.11g Wireless Access Point/Bridge Pro/Advanced User’s Guide Version: 1.1 Last Updated: 10/27/2006 i Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated ra- dio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is en- couraged to try to correct the interference by one of the following measures: z Reorient or relocate the receiving antenna. z Increase the separation between the equipment and receiver. z Connect the equipment into an outlet on a circuit different from that to which the receiver is con- nected. z Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or trans- mitter. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environ- ment. This equipment should be installed and operated with minimum distance 20 cm between the ra- diator & your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi- tions: (1) This device may not cause harmful interference, and (2) this device must accept any inter- ference received, including interference that may cause undesired operation. ii R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Termi- nal Equipment and Satellite Earth Station Equipment) as of April 8,2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. How- ever, special attention must be paid to the dangers of electric shock and static electricity when work- ing with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France (with Frequency channel restrictions), Germany, Greece, Ireland, Italy, Luxembourg, Portugal, Spain, Sweden, The Netherlands, and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states Norway and Swit- zerland. EU Countries Not Intended for Use None. Potential Restrictive Use France: only channels 10, 11, 12, and 13. iii Table of Contents 1. Introduction ......................................................................................................................... 1 1.1. Overview ...................................................................................................................1 1.2. Features.................................................................................................................... 1 1.3. Feature Comparison ................................................................................................. 3 1.4. LED Definitions ......................................................................................................... 4 2. First-Time Installation and Configuration ............................................................................ 5 2.1. Selecting a Power Supply Method ............................................................................ 5 2.2. Mounting the AP on a Wall ....................................................................................... 5 2.3. Preparing for Configuration....................................................................................... 6 2.3.1. Connecting the Managing Computer and the AP ........................................... 6 2.3.2. Changing the TCP/IP Settings of the Managing Computer ............................ 7 2.4. Configuring the AP.................................................................................................... 7 2.4.1. Entering the User Name and Password ......................................................... 7 2.4.2. Step 1: Selecting an Operational Mode .......................................................... 9 2.4.3. Step 2: Configuring TCP/IP Settings ............................................................ 11 2.4.4. Step 3: Configuring IEEE 802.11 Settings.................................................... 12 2.4.5. Step 4: Reviewing and Applying Settings ..................................................... 13 2.5. Deploying the AP .................................................................................................... 13 2.6. Setting up Client Computers ................................................................................... 15 2.6.1. Configuring IEEE 802.11g-Related Settings ................................................ 15 2.6.2. Configuring TCP/IP-Related Settings ........................................................... 15 2.7. Confirming the Settings of the AP and Client Computers ....................................... 16 2.7.1. Checking if the IEEE 802.11g-Related Settings Work....................…
Text truncated - open the document above for the full version.
SPORTON International Inc. PAGE NUMBER : A1 OF A6 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 APPENDIX A. Photographs of EUT SPORTON International Inc. PAGE NUMBER : A2 OF A6 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A3 OF A6 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A4 OF A6 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A5 OF A6 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A6 OF A TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255
SPORTON International Inc. PAGE NUMBER : A 1 OF A1 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255
SPORTON International Inc. PAGE NUMBER : A 1 OF A10 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A 2 OF A10 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A 3 OF A10 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A 4 OF A10 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A 5 OF A10 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A 6 OF A10 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A 7 OF A10 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A 8 OF A10 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A 9 OF A10 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A1 0 OF A10 TEL : 886-2-2696-2468 ISSUED DATE : Aug. 18, 2006 FAX : 886-2-2696-2255
Report No.: FR671227 FCC ID: PRL-TA6900 Page No. : 1 of 3 Appendix C. Maximum Permissible Exposure Report No.: FR671227 FCC ID: PRL-TA6900 Page No. : 2 of 3 1. Maximum Permissible Exposure 1.1. Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2 m normally can be maintained between the user and the device. (A) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 (B) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz ; *Plane-wave equivalent power density 1.2. MPE Calculation Method E (V/m) = d GP××30 Power Density: Pd (W/m²) = 377 2 E E = Electric field (V/m) P = Peak RF output power (W) G = EUT Antenna numeric gain (numeric) d = Separation distance between radiator and human body (m) The formula can be changed to Pd = 2 377 30 d GP × ×× From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. Report No.: FR671227 FCC ID: PRL-TA6900 Page No. : 3 of 3 1.3. Calculated Result and Limit Antenna Type : Dipole Max Conducted Power for IEEE 802.11b/g : 18.04dBm Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power ( mW ) Power Density (S) (mW/cm²) Limit of Power Density (S) (mW/cm²) Test Result 2 1.5849 18.0400 63.6796 0.020089 1 Complies
SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, TaoYuan Hsien, Taiwan, R.O.C. Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw Report Format Version: RF-15.247-2006-6-16-e FCC RADIO TEST REPORT Applicant’s company Interepoch Technology Inc. Applicant Address 6F, No.1, Alley 1, Lane 235, Pao-Chiao Rd., HsinTien Taipei County, Taiwan FCC ID PRL-TA6900 Manufacturer’s company Interepoch Technology Inc. Manufacturer Address 6F, No.1, Alley 1, Lane 235, Pao-Chiao Rd., HsinTien Taipei County, Taiwan Product Name DeskPoint Brand Name Teleadapt Model Name TA6900 Test Rule 47 CFR FCC Part 15 Subpart C § 15.247 Test Freq. Range 2400 ~ 2483.5MHz Received Date Jul. 17, 2006 Final Test Date Aug. 18, 2006 Submission Type Original Equipment Statement Test result included is only for the 802.11b/g part of the product. The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.4-2003 and 47 CFR FCC Part 15 Subpart C. The test equipment used to perform the test is calibrated and traceable to NML/ROC. Lab Code: 200079-0 Report No.: FR671227 Report Format Version: RF-15.247-2006-2-17-d Page No. : i of ii FCC ID: PRL-TA6900 Issued Date : Aug. 18, 2006 Table of Contents 1. CERTIFICATE OF COMPLIANCE ......................................................................................................................... 1 2. SUMMARY OF THE TEST RESULT .......................................................................................................................... 2 3. GENERAL INFORMATION .................................................................................................................................. 3 3.1. Product Details....................................................................................................................................................................................3 3.2. Accessories .........................................................................................................................................................................................3 3.3. Table for Filed Antenna.......................................................................................................................................................................3 3.4. Table for Carrier Frequencies .............................................................................................................................................................3 3.5. Table for Test Modes ...........................................................................................................................................................................4 3.6. Table for Testing Locations..................................................................................................................................................................4 3.7. Table for Supporting Units ...................................................................................................................................................................5 3.8. Table for Parameters of Test Software Setting .....................................................................................................................................5 3.9. Test Configurations .............................................................................................................................................................................6 4. TEST RESULT ..................................................................................................................................................... 9 4.1. AC Power Line Conducted Emissions Measurement...........................................................................................................................9 4.2. Maximum Peak Output Power Measurement ...................................................................................................................................15 4.3. Power Spectral Density Measurement ..............................................................................................................................................17 4.4. 6dB Spectrum Bandwidth Measurement ..........................................................................................................................................22 4.5. Radiated Emissions Measurement ....................................................................................................................................................27 4.6. Band Edge Emissions Measurement .................................................................................................................................................45 4.7. Antenna Requirements .....................................................................................................................................................................50 5. LIST OF MEASURING EQUIPMENTS ................................................................................................................... 51 6. TEST LOCATION.............................................................................................................................................. 52 7. NVLAP CERTIFICATE OF ACCREDITATION ......................................................................................................... 53 APPENDIX A. PHOTOGRAPHS OF EUT.........................................................................................................A1 ~ A16 APPENDIX B. TEST PHOTOS.......................................................................................................................... B1 ~ B6 APPENDIX C. MAXIMUM PERMISSIBLE EXPOSURE..........…
Text truncated - open the document above for the full version.
Report No.: FR671227 FCC ID: PRL-TA6900 Page No. : 1 of 6 Appendix B. Test Photos Report No.: FR671227 FCC ID: PRL-TA6900 Page No. : 2 of 6 1. Photographs of Conducted Emissions Test Configuration FRONT VIEW REAR VIEW Report No.: FR671227 FCC ID: PRL-TA6900 Page No. : 3 of 6 SIDE VIEW Report No.: FR671227 FCC ID: PRL-TA6900 Page No. : 4 of 6 2. Photographs of Radiated Emissions Test Configuration 9kHz ~1GHz FRONT VIEW REAR VIEW Report No.: FR671227 FCC ID: PRL-TA6900 Page No. : 5 of 6 FRONT VIEW REAR VIEW Report No.: FR671227 FCC ID: PRL-TA6900 Page No. : 6 of 6 Above 1GHz FRONT VIEW REAR VIEW
No. 52, Hwa Ya 1st Rd., Hwa Ya Technology Park · Tao Yuan · Taiwan
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15C | 2.41 GHz - 2.46 GHz | 63.70 mW |

Deskpoint 2 (DP2)
Equipment Class
DTS - Digital Transmission System
IEEE 802.11g HotSpot Access Gateway
Equipment Class
DTS - Digital Transmission System
High Power Wireless Access Point
Equipment Class
DTS - Digital Transmission System
Integrated High Powered Access Point
Equipment Class
DTS - Digital Transmission System
Wireless LAN 802.11b+g
Equipment Class
DTS - Digital Transmission System