PXTIGB-02Integrity Base G1.5

1 Welcome to MobileHelp Thank you for participating in our MobileHelp pilot program! MobileHelp allows you to summon emergency help 24 hours a day, 365 days a year by simply pressing your own Personal Help Button. Unlike traditional medical alert systems, MobileHelp also enables you to participate in activities that you enjoy outside of your home while having the peace-of-mind of having a medical alert system with you at all times. This short set up guide walks you through the 7 simple steps that it takes to install and activate your MobileHelp service. If you have any questions regarding the installation, please contact MobileHelp Subscriber Services at 561-347-6259. DO NOT USE IN AN EMERGENCY! DIAL 911 ON YOUR HOME OR CELL PHONE THIS SYSTEM IS FOR TEST PURPOSES ONLY 2 Package Contents Your MobileHelp package contains the following items: Base Station: When you are inside of your home, the Base Station calls for help whenever you press the red Emergency button OR your Personal Help Button. The Base Station also recharges your Portable Device. Personal Help Button: This device is worn on your person. When you press this button from within your home, it sends a signal to the Base Station. The Base Station, in turn, places a help call to the MobileHelp Response Center. Note that your Personal Help Button is also waterproof. Phone Cord: Connects your base station to your home’s phone service. Portable Device: Pressing the button on your Portable Device places a help call to the MobileHelp Response Center. As its name implies, this device is portable: Always take the Portable Device with you when you are outside of or away from your home Portable Unit Base Station Personal Help button Phone Cord 3 Step 1 Place your Base Station in a proper location Place your Base Station within 5 feet of: Base Station Phone Jack Power Supply
A telephone wall jack and electrical outlet.
In the area of your home where you spend most of your time. For large homes, place the Base Station near the center of the home. This ensures a wider range of operation for your MobileHelp system.
On a hard, flat, non-metallic surface. For example, do NOT place your Base Station on a tablecloth. Do NOT place your Base Station:
Near an electrical outlet that is controlled by a wall switch. That is, do not place the Base Station near a wall outlet that is controlled by an on/off wall switch.
Near sources of noise. For example, do NOT place your Base Station near a television, radio, air conditioner or similar devices OR Near your refrigerator and microwave oven. 4 Step 2 Plug in the Power Cord a. Plug your Base Station’s power adapter into an electrical outlet that is NOT controlled by a wall switch. After plugging in your Base Station, the Emergency and Reset buttons on the Base Station will light up. This simply indicates, that power has been detected by your Base Station. b. Place the Portable Device “face out” in the recharging cradle on top your Base Station. A red light will illuminate. This indicates that the Portable Device is charging. The red light will turn off indicating a fully- charged Portable Device. 5 Step 3 Plug the Base Station into a Wall Jack a. Plug one end of the Phone Cord (supplied with your MobileHelp system) into the LINE jack located on the back of your Base Station. b. Plug the other end of the phone cord into the wall's phone jack. If you already you have a telephone cord plugged into this jack, you will need to temporarily unplug it from the wall’s phone jack. Wall Jack Phone Cord The jack labeled “LINE” on the back of the base station. 6 Step 4 Connect your Telephone to the Base Station  If you did not have a phone that needed to be unplugged from the wall jack in Step 3, you can skip this step and go to Step 5.  If you unplugged your phone's cord from the wall phone jack in Step 3, plug the phone cord that is connected to your telephone into the PHONE jack on the back of your Base Station.  If you completed this step correctly, you should hear a dial tone on your phone. Use your regular phone cord that you use with your home phone and plug it into the back of the base station in the jack labeled “phone” Jack labeled “Phone” 7 Step 5 Conduct a Range Test The Base Station provides coverage inside your home and it may provide coverage in the area immediately outside of your home (i.e. in your yard, etc.). The range test will show you, which areas in your home are within the range that is covered by your Base Station. While not required, having a helper to assist you in completing the Range Test is encouraged. With a helper, one person can remain nearby the Base Station while the other tests the Personal Help Button from each room within your home. To perform the range test, perform these following steps: a. Temporarily unplug the phone cord that is plugged into the wall's phone jack. b. Place the Personal Help Button around your neck. c. With your Personal Help Button around your neck, walk into one of the rooms in your home. d. Once you are in the room, press your Personal Help Button to see if the Base Station responds with a “beep”. The “beep” indicates that your Personal Help Button is within the range of your Base Station. This means that your Personal Help Button is capable of sending a help call to the MobileHelp Response Center from within that room. e. Exit the room and go to your Base Station. f. On the Base Station, press the Reset button. g. Repeat Steps 3b through 3e for each room in your home. Remember to include your bathroom(s) as well. h. Plug the end of the phone cord back into the wall's phone jack. 8 After you have performed a range test for each room in your home, proceed to Step 6. If you do not hear a beep in some rooms, move the Base Station to a different location. Moving the Base Station will improve its coverage. Step 6 Use your Personal Help Button to place a test call to MobileHelp a. Test your MobileHelp system by pressing the Personal Help Button that you…

Text truncated - open the document above for the full version.

Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group APPENDIX 2 EXTERNAL PHOTOGRAPHS OF EUT Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group Front View of EUT Back View of EUT Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group Side View of EUT – 1 Side View of EUT – 2 Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or app…

Text truncated - open the document above for the full version.

Label Location Label Location

ABL IB2-02 DAVISCOMMS INTERNAL USE ONLY Page 1 Integrity Base Station G1.5, Back Label 15 Oct 2012 NOTES: 1. Model Number is IGB-02 2. Serial Number follows the Product Serial Number Determination Chart (Doc. 500107Rxx) Example : IB2XNQ2222 Integrity Base Station G1.5 (IB2), no PLL (PLL code not used “X”), Factory Ship Year is 2012 (Year Code “N”). Factory Ship Month is first half month of August (Month Code “Q”), unit sequence code (2222). 65.6mm 27.4mm SERIAL NUMBER BARCODE 39 MobileHelp Made in Malaysia Model Number: IGB-02 Serial Number: FCC ID: PXTIGB-02 US: PXTAL02BIGB-02 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group APPENDIX 3 INTERNAL PHOTOGRAPHS OF EUT Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group Open View of EUT-1 Open View of EUT-2 Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group Internal of EUT – 1 Internal of EUT – 2 Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or ap…

Text truncated - open the document above for the full version.

Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Page: 1 of 30 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF Product Name: Integrity Base G1.5 Marketing Name: Integrity Base Station Gen 1.5 Brand Name: MobileHelp Model No.: IGB-02 Model Different: N/A FCC ID: PXTIGB-02 Report No.: EF/2012/90001 Issue Date: Nov. 12, 2012 Rule Part: §15.231 Prepared by: Integrity Tracking LLC, dba MobileHelp 3701 FAU Blvd., Suite 300, Boca Raton FL 33431, USA Prepared by: SGS Taiwan Ltd. Electronics & Communication Laboratory No.134, Wu Kun g Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803 Note: This report shall not be reproduced except in full, without the written approval of SGS Taiwan Ltd. This document may be altered or revised by SGS Taiwan Ltd. personnel only, and shall be noted in the revision section of the document. Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Page: 2 of 30 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group VERIFICATION OF COMPLIANCE Applicant: Integrity Tracking LLC, dba MobileHelp 3701 FAU Blvd., Suite 300, Boca Raton FL 33431, USA Product Name: Integrity Base G1.5 Marketing Name: Integrity Base Station Gen 1.5 Brand Name: MobileHelp FCC ID: PXTIGB-02 Model No.: IGB-02 Model Difference: N/A File Number: EF/2012/90001 Date of test: Sep. 05, 2012 ~ Nov. 12, 2012 Date of EUT Received: Sep. 05, 2012 We hereby certify that: The above equipment was tested by SGS Taiwan Ltd. Electronics & Communication Laboratory The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2009) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.231. The test results of this report relate only to the tested sample identified in this report. Test By: Date: Nov. 12, 2012 Marcus Tseng / Engineer Prepared By: Date: Nov. 12, 2012 Judy Hsu / Clerk Approved By: Date: Nov. 12, 2012 Jim Chang / Supervisor Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Page: 3 of 30 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibil…

Text truncated - open the document above for the full version.

Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group APPENDIX 1 PHOTOGRAPHS OF SET UP Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group Radiated Emission Setup Photos Report No: EF/2012/90001 FCC ID: PXTIGB-02 Issue Date: Nov. 12, 2012 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group Conducted Emission Setup Photos