PY314100257N300 Wireless Router

350 East Plumeria Drive San Jose, CA 95134 USA April 2014 202-11392-01 N300 Wireless Router User Manual Models: JWNR2010v5 WNR2020 WNR614 2 N300 Wireless Router Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com. Phone (US & Canada only): 1-888-NETGEAR. Phone (Other Countries): Check the list of phone numbers at http://support.netgear.com/general/contact/default.aspx. Compliance For regulatory compliance information, visit http://www.netgear.com/about/regulatory. See the regulatory compliance document before connecting the power supply. Trademarks NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. © NETGEAR, Inc. All rights reserved. 3 Contents Chapter 1 Hardware Setup Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Position Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Cable Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Verify the Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Chapter 2 Connect to the Network and Access the Router Connect to the Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Wired Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 WiFi Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Types of Logins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Use a Web Browser to Access the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 NETGEAR genie Automatic Internet Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Log In to the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Chapter 3 Specify Your Internet Settings Use the Internet Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Manually Set Up the Internet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Specify an Internet Connection Without a Login . . . . . . . . . . . . . . . . . . . . . . . 18 Specify an Internet Connection That Uses a Login . . . . . . . . . . . . . . . . . . . . . 19 Change the MTU Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Chapter 4 Networking View or Change WAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Set Up a Default DMZ Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Change the Router’s Device Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Change the LAN TCP/IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Specify the IP Addresses that the Router Assigns . . . . . . . . . . . . . . . . . . . . . . . . 30 Disable the DHCP Server Feature in the Router . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Reserve LAN IP Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Use the WPS Wizard for WiFi Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Specify Basic WiFi Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Change the WiFi Security Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Set Up a Guest Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Control the Wireless Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Enable or Disable the Wireless Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 4 N300 Wireless Router Set Up a Wireless Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Set up a Wireless Access List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Specify WPS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Wireless Distribution System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Set Up the Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Set Up a Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Static Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 View Devices Currently on the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Improve Network Connections with Universal Plug and Play . . . . . . . . . . . . . . . 49 Chapter 5 Manage Your Network Update the Router Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . .…

Text truncated - open the document above for the full version.

Notification of Compliance Regulatory Compliance Information This document includes user requirements for operating NETGEAR products in accordance with national laws including usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable national regulatory authority. The NETGEAR product firmware limits operation to only the channels allowed in a particular region or country. Therefore, all options described in this document may not be available in your version of the product. This document applies to both Class A and Class B devices:  Class A devices are intended to be used in a commercial or industrial environment. They are not intended to be used in a residential home or be available for general public use.  Class B devices are intended to be used in a residential setting, and may also be used in commercial and industrial applications. Examples of Class B devices are telephones, personal computers, and residential data gateways.  Fuses should only be installed by service personnel.  NETGEAR recommends the use of 26 AWG or larger gauge phone line cords. Europe – EU Declaration of Conformity This section applies to products bearing the CE or CE! mark: Products bearing the CE or CE! mark comply with the following EU directives:  EMC Directive 2004/108/EC  Low Voltage Directive 2006/95/EC  Ecodesign Directive 2009/125/EC  RoHS Directive 2011/65/EU If the product has telecommunications functionality, it also complies with the requirement of the following EU directive:  R&TTE Directive 1999/5/EC Compliance with these directives implies conformity to harmonized European standards that are noted in the EU Declaration of Conformity. The EU CE Declaration of Conformity may be found at http://support.netgear.com/app/answers/detail/a_id/11621/. Caution for installing this equipment outdoors: (Valid in all EU member states, EFTA states, and Switzerland.) Be aware that outdoor installations require special attention and will only be handled by trained and qualified installation personnel. No one from the general public is permitted to install NETGEAR wireless products outdoors when external antennas, power and grounding must be installed for use. Particular attention has to be given allowed operational frequencies. Contact NETGEAR for instructions on how to contact an installer for outdoor operations if this product requires the special considerations for outdoor installations. For detailed iformation concerning installations in France, the user should contact the national spectrum authority in France (http://www.arcep.fr/ ) The following paragraphs apply to WN2500RP: This device is a 2.4GHz and 5GHz wideband transmission system (transceiver), intended for indoor use only in all EU member states, EFTA states, and Switzerland. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for applying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10mW EIRP in the frequency range of 2454-2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. Warning NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference in which case the user may be required to take adequate measures. FCC Requirements for Operation in the United States Information in this section applies to products bearing the FCC mark (or statement): FCC Information to User This NETGEAR product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals. The following statement applies to these products:  A6210  JWNR2000v5  WN3500RP  C6300  JWNR2010v5  WNR2010  C6300XB3  R6050  WNR2020  D6200v2  STS7000  WNR614  EX6100  VEGN2200  WNR618  EX6200  WN370  HMNC100  WN2500RP  JR6150  WN3000RPv2 This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. FCC Guidelines for Human Exposure The NETGEAR product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. The following statement applies to this product:  C6300XB3 This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device should be installed and operated with minimum distance of 25 cm between the radiator and your body. FCC Declaration of Conformity We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that this product complies with Part 15 Subpart B of FCC CFR47 Rules. Operation is subject to the following two conditions:  The device may not cause harmful interference, and  The device must accept any interference received, including interference that may cause undesired operation. FCC Radio Frequency Interference Warnings & Instructions The NETGEAR product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particu…

Text truncated - open the document above for the full version.

Notification of Compliance Regulatory Compliance Information This document includes user requirements for operating NETGEAR products in accordance with national laws including usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable national regulatory authority. The NETGEAR product firmware limits operation to only the channels allowed in a particular region or country. Therefore, all options described in this document may not be available in your version of the product. This document applies to both Class A and Class B devices:  Class A devices are intended to be used in a commercial or industrial environment. They are not intended to be used in a residential home or be available for general public use.  Class B devices are intended to be used in a residential setting, and may also be used in commercial and industrial applications. Examples of Class B devices are telephones, personal computers, and residential data gateways.  Fuses should only be installed by service personnel.  NETGEAR recommends the use of 26 AWG or larger gauge phone line cords. Europe – EU Declaration of Conformity This section applies to products bearing the CE or CE! mark: Products bearing the CE or CE! mark comply with the following EU directives:  EMC Directive 2004/108/EC  Low Voltage Directive 2006/95/EC  Ecodesign Directive 2009/125/EC  RoHS Directive 2011/65/EU If the product has telecommunications functionality, it also complies with the requirement of the following EU directive:  R&TTE Directive 1999/5/EC Compliance with these directives implies conformity to harmonized European standards that are noted in the EU Declaration of Conformity. The EU CE Declaration of Conformity may be found at http://support.netgear.com/app/answers/detail/a_id/11621/. Caution for installing this equipment outdoors: (Valid in all EU member states, EFTA states, and Switzerland.) Be aware that outdoor installations require special attention and will only be handled by trained and qualified installation personnel. No one from the general public is permitted to install NETGEAR wireless products outdoors when external antennas, power and grounding must be installed for use. Particular attention has to be given allowed operational frequencies. Contact NETGEAR for instructions on how to contact an installer for outdoor operations if this product requires the special considerations for outdoor installations. For detailed iformation concerning installations in France, the user should contact the national spectrum authority in France (http://www.arcep.fr/ ) The following paragraphs apply to WN2500RP: This device is a 2.4GHz and 5GHz wideband transmission system (transceiver), intended for indoor use only in all EU member states, EFTA states, and Switzerland. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for applying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10mW EIRP in the frequency range of 2454-2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. Warning NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference in which case the user may be required to take adequate measures. FCC Requirements for Operation in the United States Information in this section applies to products bearing the FCC mark (or statement): FCC Information to User This NETGEAR product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals. The following statement applies to these products:  A6210  JWNR2000v5  WN3500RP  C6300  JWNR2010v5  WNR2010  C6300XB3  R6050  WNR2020  D6200v2  STS7000  WNR614  EX6100  VEGN2200  WNR618  EX6200  WN370  HMNC100  WN2500RP  JR6150  WN3000RPv2 This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. FCC Guidelines for Human Exposure The NETGEAR product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. The following statement applies to this product:  C6300XB3 This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device should be installed and operated with minimum distance of 25 cm between the radiator and your body. FCC Declaration of Conformity We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that this product complies with Part 15 Subpart B of FCC CFR47 Rules. Operation is subject to the following two conditions:  The device may not cause harmful interference, and  The device must accept any interference received, including interference that may cause undesired operation. FCC Radio Frequency Interference Warnings & Instructions The NETGEAR product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particu…

Text truncated - open the document above for the full version.

Federal Communications Commission 7435 Oakland Mills Rd Columbia MD 21046 Subject: Product Certification Representative Authorization Letter FCC ID: To whom it may concern: We the undersigned, hereby authorize following person to act for equipment authorization o the FCC Rules and Regulations. International Certification Corp. Address Name Job Title e-mail We further 1.2002(b), is subject to a Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This appointment also application as an authorized agent. Applicant Address Signature Name and Job E-mail Tel. Federal Communications Commission 7435 Oakland Mills Rd Columbia MD 21046 Subject: Product Certification Representative Authorization Letter FCC ID: PY314100257 To whom it may concern: e the undersigned, hereby authorize following person to act for equipment authorization o the FCC Rules and Regulations. International Certification Corp. ddress : No.3-1, Lane 6, Wen San 3rd St. Kwei Shan Hsiang, Tao Yuan Hsein 333, Taiwan (R.O.C.) : Gary Chang itle : Manager : garychang e further certifies that neither t 1.2002(b), is subject to a Drug Abuse Act of 1998, 21 U.S.C. 835(a). This appointment also application as an authorized agent. Applicant Address Signature Name and Job Title. 350 East Plumeria Drive San Jose, CA 95134 U.S.A. Federal Communications Commission 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Certification Representative Authorization Letter PY314100257 To whom it may concern: e the undersigned, hereby authorize following person to act for equipment authorization o the FCC Rules and Regulations. International Certification Corp. 1, Lane 6, Wen San 3rd St. Kwei Shan Hsiang, Tao Yuan Hsein 333, Taiwan (R.O.C.) Gary Chang Manager [email protected] certifies that neither t 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Drug Abuse Act of 1998, 21 U.S.C. 835(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. : NETGEAR, Inc. : 350 East Plumeria Drive, San Jose, California 95134, USA : _________________________________ . : David Kay / Regulatory Compliance Manager : [email protected] : 408-890 NETGEAR 350 East Plumeria Drive San Jose, CA 95134 U.S.A. Federal Communications Commission Subject: Product Certification Representative Authorization Letter e the undersigned, hereby authorize following person to act for equipment authorization o the FCC Rules and Regulations. International Certification Corp. 1, Lane 6, Wen San 3rd St. Kwei Shan Hsiang, Tao Yuan Hsein 333, Taiwan @icertifi.com.tw Webs certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Drug Abuse Act of 1998, 21 U.S.C. 835(a). includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. NETGEAR, Inc. 350 East Plumeria Drive, San Jose, California 95134, USA _________________________________ David Kay / Regulatory Compliance Manager [email protected] 890-3160 ETGEAR 350 East Plumeria Drive San Jose, CA 95134 U.S.A. Subject: Product Certification Representative Authorization Letter e the undersigned, hereby authorize following person to act for equipment authorization o the FCC Rules and Regulations. 1, Lane 6, Wen San 3rd St. Kwei Shan Hsiang, Tao Yuan Hsein 333, Taiwan Webs he applicant nor any party to this application, as defined in 47 CFR Ch. denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Drug Abuse Act of 1998, 21 U.S.C. 835(a). includes the authority to complete FCC Form 731 on our behalf and sign the 350 East Plumeria Drive, San Jose, California 95134, USA _________________________________ David Kay / Regulatory Compliance Manager [email protected] ETGEAR Inc. 350 East Plumeria Drive San Jose, CA 95134 U.S.A. Subject: Product Certification Representative Authorization Letter e the undersigned, hereby authorize following person to act as our agent in the preparation of an application for equipment authorization o the FCC Rules and Regulations. 1, Lane 6, Wen San 3rd St. Kwei Shan Hsiang, Tao Yuan Hsein 333, Taiwan he applicant nor any party to this application, as defined in 47 CFR Ch. denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the includes the authority to complete FCC Form 731 on our behalf and sign the 350 East Plumeria Drive, San Jose, California 95134, USA _________________________________ David Kay / Regulatory Compliance Manager Inc. 350 East Plumeria Drive San Jose, CA 95134 U.S.A. as our agent in the preparation of an application 1, Lane 6, Wen San 3rd St. Kwei Shan Hsiang, Tao Yuan Hsein 333, Taiwan he applicant nor any party to this application, as defined in 47 CFR Ch. denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the includes the authority to complete FCC Form 731 on our behalf and sign the 350 East Plumeria Drive, San Jose, California 95134, USA David Kay / Regulatory Compliance Manager 350 East Plumeria Drive San Jose, CA 95134 U.S.A. Date: as our agent in the preparation of an application 1, Lane 6, Wen San 3rd St. Kwei Shan Hsiang, Tao Yuan Hsein 333, Taiwan he applicant nor any party to this application, as defined in 47 CFR Ch. denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the includes the authority to complete FCC Form 731 on our behalf and sign the 350 East Plumeria Drive, San Jose, California 95134, USA Date: 2014/4/23 as our agent in the preparation of an application 1, Lane 6, Wen San 3rd St. Kwei Shan Hsiang, Tao Yuan Hsein 333, Taiwan he applicant nor any party to this application, as defined in 47 CFR Ch. denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the includes the authority to complete FCC Form 73…

Text truncated - open the document above for the full version.

Date: April 23, 2014 Subject: Ad Hoc Mode Function Declaration To whom it may concern, We, NETGEAR, Inc. country code selection in all the operational mode(s) for the following product. FCC ID: PY314100257 IC : 4054A- Regards, Applicant’s company name Applicant’s Signature Name and Job Title E-Mail Tel. April 23, 2014 Subject: Ad Hoc Mode Function Declaration it may concern, NETGEAR, Inc. country code selection in all the operational mode(s) for the following product. PY314100257 -14100257 Applicant’s company name Applicant’s company address Name and Job Title 350 East Plumeria Drive San Jose, Subject: Ad Hoc Mode Function Declaration it may concern, declare that the device does not support any non country code selection in all the operational mode(s) for the following product. PY314100257 Applicant’s company name : company address : : : : : NETGEAR 350 East Plumeria Drive San Jose, Subject: Ad Hoc Mode Function Declaration declare that the device does not support any non country code selection in all the operational mode(s) for the following product. : NETGEAR, : 350 East Plumeria Drive, San Jose, California 95134, USA : : David Kay / Regulatory Compliance Manager : [email protected] : 408-890-3 ETGEAR 350 East Plumeria Drive San Jose, Subject: Ad Hoc Mode Function Declaration declare that the device does not support any non country code selection in all the operational mode(s) for the following product. NETGEAR, Inc. East Plumeria Drive, San Jose, California 95134, USA David Kay / Regulatory Compliance Manager [email protected] 3160 ETGEAR Inc. 350 East Plumeria Drive San Jose, CA 95134 U.S.A. declare that the device does not support any non country code selection in all the operational mode(s) for the following product. East Plumeria Drive, San Jose, California 95134, USA David Kay / Regulatory Compliance Manager [email protected] Inc. CA 95134 U.S.A. declare that the device does not support any non country code selection in all the operational mode(s) for the following product. East Plumeria Drive, San Jose, California 95134, USA David Kay / Regulatory Compliance Manager CA 95134 U.S.A. declare that the device does not support any non-US channels and country code selection in all the operational mode(s) for the following product. East Plumeria Drive, San Jose, California 95134, USA David Kay / Regulatory Compliance Manager US channels and country code selection in all the operational mode(s) for the following product. East Plumeria Drive, San Jose, California 95134, USA US channels and

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046 Subject: Request for FCC ID: PY314100257 To whom it may concern Short-term confidentiality Pursuant to DA 04 47CFR §2.803 and the importation rules in 47 CFR remains confidential until the actual marketing of newly authorized devices. We are requesting grant short- ☒ Internal Photographs ☒ External Photographs ☒ User's manual ☒ Test Set up photo Permanent Pursuant to Sections 0.457 and 0.459 of the Commission treatment of information ☒ Block Diagram ☒ Schematics ☒ Operation description The above materials contain trade secrets and proprietary information not customarily released to the The public disclosure of these materials may be harmful to the applic competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this applica Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Applicant Address Signature Name and Job E-mail Tel. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for confidentiality PY314100257 To whom it may concern term confidentiality Pursuant to DA 04-1705 of the Commission’s 2.803 and the importation rules in 47 CFR remains confidential until the actual marketing of newly authorized devices. We are requesting -term confidentiality Internal Photographs External Photographs User's manual Test Set up photo confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission treatment of information Diagram Schematics Operation description The above materials contain trade secrets and proprietary information not customarily released to the The public disclosure of these materials may be harmful to the applic competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this applica Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Applicant Address Signature Name and Job Title mail 350 East Plumeria Drive San Jose, CA 95134 U.S.A. Federal Communications Commission Authorization and Evaluation Division 1609 confidentiality PY314100257 To whom it may concern: term confidentiality 1705 of the Commission’s 2.803 and the importation rules in 47 CFR remains confidential until the actual marketing of newly authorized devices. We are requesting term confidentiality request on the following attachments Internal Photographs External Photographs confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission treatment of information accompanying Operation description The above materials contain trade secrets and proprietary information not customarily released to the The public disclosure of these materials may be harmful to the applic The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this applica Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. : NETGEAR, In…

Text truncated - open the document above for the full version.