PY314300282G54/N150 WiFi USB Micro Adapter

Notification of Compliance Regulatory Compliance Information This document includes user requirements for operating NETGEAR products in accordance with national laws including usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable national regulatory authority. The NETGEAR product firmware limits operation to only the channels allowed in a particular region or country. Therefore, all options described in this document may not be available in your version of the product. This document applies to both Class A and Class B devices:  Class A devices are intended to be used in a commercial or industrial environment. They are not intended to be used in a residential home or be available for general public use.  Class B devices are intended to be used in a residential setting, and may also be used in commercial and industrial applications. Examples of Class B devices are telephones, personal computers, and residential data gateways.  Fuses should only be installed by service personnel.  NETGEAR recommends the use of 26 AWG or larger gauge phone line cords. Europe – EU Declaration of Conformity This section applies to products bearing the CE or CE! mark: Products bearing the CE or CE! mark comply with the following EU directives:  EMC Directive 2004/108/EC  Low Voltage Directive 2006/95/EC  Ecodesign Directive 2009/125/EC  RoHS Directive 2011/65/EU If the product has telecommunications functionality, it also complies with the requirement of the following EU directive:  R&TTE Directive 1999/5/EC Compliance with these directives implies conformity to harmonized European standards that are noted in the EU Declaration of Conformity. The EU CE Declaration of Conformity may be found at http://support.netgear.com/app/answers/detail/a_id/11621/. Caution for installing this equipment outdoors: (Valid in all EU member states, EFTA states, and Switzerland.) Be aware that outdoor installations require special attention and will only be handled by trained and qualified installation personnel. No one from the general public is permitted to install NETGEAR wireless products outdoors when external antennas, power and grounding must be installed for use. Particular attention has to be given allowed operational frequencies. Contact NETGEAR for instructions on how to contact an installer for outdoor operations if this product requires the special considerations for outdoor installations. For detailed information concerning installations in France, the user should contact the national spectrum authority in France (http://www.arcep.fr/ ) The following paragraphs apply to WN2500RP: This device is a 2.4GHz and 5GHz wideband transmission system (transceiver), intended for indoor use only in all EU member states, EFTA states, and Switzerland. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for applying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10mW EIRP in the frequency range of 2454-2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. Warning NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference in which case the user may be required to take adequate measures. FCC Requirements for Operation in the United States Information in this section applies to products bearing the FCC mark (or statement): FCC Information to User This NETGEAR product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals. The following statement applies to these products:  C6300  GS205v2  STS7000  WNR2010  C7000BMX  GS208v2  VEGN2200  WNR2020  D6000  GS305  VMB3000  WNR614  D6010  GS308v2  VMC3010  WNR618  D3600  GS605v5  VMC3030  D3610  GS608v4  WN370  D6200V2  HMNC100  WN1000v4  EX2700  JNR1010v2  WN2500RP  EX6100  JR6150  WN3000RPv2  EX6200  JWNR2000v5  WN3500RP  FS205v2  JWNR2010v5  WNA1000Mv2  FS208v2  R6050  WNDA3100v3  FS305v2  R6200v3  WNDR3400v3  FS308v2  R6220  WNDR3700v5  FS605v4  R7500  WNDR4300v2  FS608v4  R8000  WNDR4500v3 This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. FCC Guidelines for Human Exposure The NETGEAR product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. The following statement applies to this product:  C6300BD This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device should be installed and operated with minimum distance of 35cm between the radiator and your body. The following statement applies to this product:  C6300XB3 This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device should be installed and operated with minimum distance of 25cm between the radiator and your body. The following statement applies to this product:  R8000 This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device should be installed and operated with minimum distance of 30cm between the radiator and your body. FCC Declaration of Conformity We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that this pr…

Text truncated - open the document above for the full version.

Quick Start G54/N150 WiFi USB Micro Adapter Model WNA1000Mv2 2. Click the Setup button . The Software Update Check screen displays. 3. Install the setup software. You have two options: • Connected to the Internet. If you are connected to the Internet, click the Check for Updates button. After the software checks for updates, the Update Check Complete screen displays. Click the Continue button. The Welcome screen displays. • Not connected to the Internet. If you are not connected to the Internet, click the Install from CD button. The Welcome screen displays. 4. To accept the license agreement, select the I agree radio button and click the Next button. A message displays asking you to wait while software is installed. After a few minutes, NETGEAR genie prompts you to insert your adapter. 5. Inset the adapter into a USB port on your computer. 6. Return to the NETGEAR genie screen and click the Next button. NETGEAR genie displays a list of wireless networks in your area. Standalone Driver Installation 1. Insert the resource CD in your computer CD drive. Note: If your computer does not have a CD drive, download the WNA1000Mv2 resource CD driver by visiting http://support.netgear.com. Click the Support For Home button and enter WNA1000Mv2 in the search field. If the Resource CD screen does not display, browse the files on the CD and double-click Autorun.exe. The NETGEAR Resource CD screen displays. 2. Click the Install Windows Standalone Driver button . The driver installs on your computer. 3. When prompted, insert the adapter into a USB port on your computer. Package Contents Installation 1. Insert the resource CD in your computer CD drive. Note: If your computer does not have a CD drive, download the WNA1000Mv2 resource CD driver by visiting http://support.netgear. com. Click the Support For Home button and enter WNA1000Mv2 in the search field. If the Resource CD screen does not display, browse the files on the CD and double-click Autorun.exe. The NETGEAR Resource CD screen displays. AdapterResource CD July 2014 NETGEAR, Inc. 350 East Plumeria Drive San Jose, CA 95134, USA NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. © NETGEAR, Inc. All rights reserved. Join a Wireless Network You can join a wireless network from NETGEAR genie, or you can use Wi-Fi Protected Setup (WPS) if your wireless router supports it. Join a Network Using NETGEAR genie 1. Insert the adapter into a USB port on your computer. 2. Click the NETGEAR genie icon that displays on the Windows systems tray or on the desktop. The NETGEAR genie Home screen displays. 3. Click the Join a Network button. 4. Select your wireless network. 5. Click the Connect button. 6. If the network is secure, enter its password or network key. The adapter joins the network, which can take a few minutes. Your settings are saved in a profile. Join a Network Using WPS 1. Press and hold the WPS button on the adapter for two seconds. 2. Within two minutes, press the WPS button on your wireless router or gateway. The adapter joins the network, which can take a few minutes. Your settings are saved in a profile. Check Your Connection Status When you install your adapter, the NETGEAR genie icon displays in the Windows system tray and on the desktop. You can double-click this icon to open NETGEAR genie to make changes or connect to a different wireless network. The color of the icon indicates the strength of your wireless connection: White. Strong connection Yellow. Weak connection Red. No connection If you remove your adapter, NETGEAR genie is not available, so the icon does not display. When you insert the adapter again, the icon returns. Support Thank you for purchasing this NETGEAR product. After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com. NETGEAR recommends that you use only the official NETGEAR support resources. You can get the user manual online at http://downloadcenter.netgear.com or through a link in the product’s user interface. For the complete EU Declaration of Conformity, visit http://support.netgear.com/app/answers/detail/a_id/11621/. For regulatory compliance information, visit http://www.netgear.com/about/regulatory/. See the regulatory compliance document before connecting the power supply. WPS button

Page: 1

Notes: 1.印刷居中,颜色为白色 2.尺寸公差:+/-0.2 3. 單位：mm 4.所用材质需符合ROHS 11 1 2014.07.17 WNA1000Mv2 Netgear 印刷颜色: White 4.1 1.6 鐳雕 Model:WNA1000Mv2S/N:MAC: IC: 4054A-14300282FCC ID: PY314300282 12.00 12.01 22.29 16.59 Made in Chin a Model:WNA1000Mv2 S/N: MAC: IC: 4054A-14300282 FCC ID: PY314300282 Made in China

Page: 2 Page: 3

FCC ID: PY314300282 Report No.: RF110826C12E Operational Description This device is a G54/N150 WiFi USB Micro Adapter, which operates in 2.4GHz bands; the maximum data rate could be up to 150Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 150Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by DC 5V from host equipment. The antennas provided to the EUT, please refer to the following table. The other instruction, please have a look at the users manual.

FCC SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 23 Report No. : SA110826C12E Issued Date : Sep. 24, 2014 Reference No.: 140701D04 FCC SAR Test Report Report No. : SA110826C12E Applicant : Netgear Incorporated Address : 350 East Plumeria Drive, San Jose, CA 95134, USA Product : G54/N150 WiFi USB Micro Adapter FCC ID : PY314300282 Brand : NETGEAR Model No. : WNA1000Mv2 Standards : FCC 47 CFR Part 2 (2.1093) / IEEE C95.1:1992 / IEEE 1528:2003 IEEE 1528a-2005 / KDB 865664 D01 v01r03 / KDB 248227 D01 v01r02 KDB 447498 D01 v05r02 / KDB 447498 D02 v02 Sample Received Date : Jul. 01, 2014 Date of Testing : Aug. 02, 2014 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch – Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Evonne Liu / Specialist Approved By : Roy Wu / Manager This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. FCC SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 23 Report No. : SA110826C12E Issued Date : Sep. 24, 2014 Reference No.: 140701D04 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 6 3.2 SPEAG DASY System ................................................................................................................................................. 6 3.2.1 Robot.................................................................................................................................................................. 7 3.2.2 Probes ................................................................................................................................................................ 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................... 8 3.2.4 Phantoms ........................................................................................................................................................... 9 3.2.5 Device Holder ................................................................................................................................................... 10 3.2.6 System Validation Dipoles ................................................................................................................................ 10 3.2.7 Tissue Simulating Liquids ................................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 14 3.4 SAR Measurement Procedure ................................................................................................................................... 15 3.4.1 Area & Zoom Scan Procedure ......................................................................................................................... 15 3.4.2 Volume Scan Procedure................................................................................................................................... 15 3.4.3 Power Drift Monitoring ...................................................................................................................................... 16 3.4.4 Spatial Peak SAR Evaluation ........................................................................................................................... 16 3…

Text truncated - open the document above for the full version.

Report No.: RF110826C12E 1 of 57 Report Format Version 5.2.1 Reference No.: 140701D04 FCC TEST REPORT (15.247) REPORT NO.: RF110826C12E MODEL NO.: WNA1000Mv2 FCC ID: PY314300282 RECEIVED: July 01, 2014 TESTED: July 16 to 18, 2014 ISSUED: Sep. 23, 2014 APPLICANT: Netgear Incorporated ADDRESS: 350 East Plumeria Drive, San Jose, CA 95134, USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF110826C12E 2 of 57 Report Format Version 5.2.1 Reference No.: 140701D04 Table of Contents RELEASE CONTROL RECORD ........................................................................................ 4 1. CERTIFICATION .................................................................................................... 5 2. SUMMARY OF TEST RESULTS ............................................................................ 6 2.1 MEASUREMENT UNCERTAINTY .......................................................................... 7 3. GENERAL INFORMATION ..................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ....................................................................... 8 3.2 DESCRIPTION OF TEST MODES ....................................................................... 10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................ 11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 13 3.4 DUTY CYCLE OF TEST SIGNAL ......................................................................... 14 3.5 DESCRIPTION OF SUPPORT UNITS .................................................................. 15 3.6 CONFIGURATION OF SYSTEM UNDER TEST ................................................... 15 4. TEST TYPES AND RESULTS .............................................................................. 16 4.1 CONDUCTED EMISSION MEASUREMENT ........................................................ 16 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ...................................... 16 4.1.2 TEST INSTRUMENTS .......................................................................................... 16 4.1.3 TEST PROCEDURES .......................................................................................... 17 4.1.4 DEVIATION FROM TEST STANDARD ................................................................. 17 4.1.5 TEST SETUP ....................................................................................................... 17 4.1.6 EUT OPERATING CONDITIONS ......................................................................... 18 4.1.7 TEST RESULTS ................................................................................................... 19 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 21 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 21 4.2.2 TEST INSTRUMENTS .......................................................................................... 22 4.2.3 TEST PROCEDURES .......................................................................................... 24 4.2.4 DEVIATION FROM TEST STANDARD ................................................................. 24 4.2.5 TEST SETUP ....................................................................................................... 25 4.2.6 EUT OPERATING CONDITIONS ......................................................................... 25 4.2.7 TEST RESULTS ................................................................................................... 26 4.3 6dB BANDWIDTH MEASUREMENT .................................................................... 39 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT .................................................. 39 4.3.2 TEST INSTRUMENTS .......................................................................................... 39 4.3.3 TEST PROCEDURE ............................................................................................. 39 4.3.4 DEVIATION FROM TEST STANDARD ................................................................. 39 4.3.5 TEST SETUP ...............................................................…

Text truncated - open the document above for the full version.

FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA110826C12E Reference No.: 140701D04 <Photographs of SAR Setup> USB Horizontal Up with 0.5 cm Gap USB Horizontal Down with 0.5 cm Gap USB Vertical Front with 0.5 cm Gap USB Vertical Back with 0.5 cm Gap Tip Mode with 0.5 cm Gap

Report No.: 140407E07 1 of 4 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 140407E07 2 of 4 RADIATED EMISSION TEST (Below 1GHz) Report No.: 140407E07 3 of 4 RADIATED EMISSION TEST (Above 1GHz) Report No.: 140407E07 4 of 4