PY314300285AC1900 WiFi Cable Modem Router

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 30cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only.

DOCSIS 3.0 AC1900 Voice and Data Cable Gateway, C7000B The NETGEAR Difference AC1900 WiFi speeds plus Beamforming+ for the ultimate in speed, ease of use and reliability The new NETGEAR DOCSIS® 3.0 AC1900 Voice and Data Cable Gateway (C7000B), gives service providers the ultimate experience for their end-users. The NETGEAR C7000B raises the bar with its incredibly fast WiFi giving service provider’s subscribers the power to connect to all of their smartphones, tablets and mobile devices faster than ever before. Enhancing end-user’s ultra-fast WiFi connection is the addition of explicit and implicit Beamforming+ creating better range and a stronger connection that is ideal for large homes. Built-in NETGEAR genie® offers end-users complete access and management of their home network, resulting in fewer technical support calls. NETGEAR Enhanced Support Tools offer easy troubleshooting for cable operators providing unprecedented visibility and diagnostic tools to ensure carrier-grade voice services. • 11ac ultra-fast cable Internet speeds up to 1 Gbps with NETGEAR Beamforming+ for expanded coverage and a better WiFi connection • NETEGAR genie® application for simplified home network management • Enhanced support tools with TR-069, SNMP and genie app • Hotspot/WiFi offload support using GRE soft tunnel • ReadyShare USB hard drive access through local network • Live parental controls Benefits • 11ac AC1900 WiFi – 600+1300 Mbps † speeds • Up to 1 Gig DOCSIS download speed with 24 bonded channels • Explicit and implicit Beamforming+ for improved WiFi range and performance • High powered amplifiers and antennas to extend WiFi coverage • Upstream and downstream advanced Quality of Service (QoS) for best gaming and video streaming experience • Integrated 4-port Gigabit Ethernet switch • Next generation of HD voice with PacketCable 2.0 Ease of Use • Installation and management is simple and easy with Push ‘N’ Connect and NETGEAR genie app • NETGEAR genie has a host a features to give end-users ultimate access and control of their network: – Home network management – MyMedia: Find and play media files from network – Turbo Transfer: Share files within home network between PC, MAC or Android – Guest Network and EZ Mobile Connect: Separate and secure access for guests; scan QR code to connect guests to the network C7000B Data Sheet - Preliminary C7000B Data Sheet Self-Install No-Click Training FW Upgrade DOCSIS, SNMP & TR-069 Remote Care TR-069 ACS (multiple vendors) TR-069/ DOCSIS/ SNMP InstallationPost-Installation TR-069/ DOCSIS Self-Care Integrated Gateway Tools genie Assisted Care Optional: NETGEAR Support Center DUAL BAND 1900 ReadyShare USBBeamforming+ DLNAWPS Data Sheet DOCSIS 3.0 AC1900 Voice and Data Cable Gateway, C7000B C7000B Technical Specifications System Requirements • Cable broadband Internet service • Microsoft® Windows® 7, 8, Vista®, XP, 2000, Mac OS®, or other operating systems running a TCP/IP network • Microsoft® Internet Explorer® 5.0, Firefox® 2.0, Safari® 1.4, or Google Chrome™ 11.0 browsers or higher • Use laptop with 3x3 450 Mbps adapter like Centrino® 6300/5300 for maximum performance • Use with an 802.11ac adapter like NETGEAR A6200 for maximum performance Physical Interfaces • 1: USB 2.0 port • 1: Coaxial port for cable Internet • 2: Voice ports • 4: Gigabit Ethernet ports with auto-sensing technology Security • WPA/WPA2 – PSK • SPI and NAT firewall • Denial-of-Service (DoS) attack prevention • WPS Power • 12V/3.5A Environmental Specifications • Operating Temperature: 5–40 ºC • RoHS/REACH/WEEE Compliant Warranty • Standard 2-year Network Management • Remote GUI Management • Genie® GUI Management • uPnP • DLNA • Port forwarding/Port Triggering • DHCP Server LEDs • Power • DS/US • ONLINE • Telephony • 2.4GHz • 5GHz • WPS • WiFi Ease-of-use • NETGEAR genie for PCs, iPad, tablets, MacBook Air, and smartphones • Push ‘N’ Connect using WiFi Protected Setup® (WPS)1 Advanced Features • 24x8 3.0 Modem • Download and upload speeds up to 1.2 Gbps • IPv6 • Simultaneous dual-band WiFi • WiFi Transmitters/Receivers (Tx/Rx)- 3x3 (2.4GHz) + 3x3 (5GHz) • WiFi Boost with high-powered radio amplifiers • Memory – 128 MB flash and 256 MB RAM • Advanced QoS • Four Gigabit Ethernet ports NETGEAR Green Features • Power On/Off button • Wireless On/Off button • 80% recycled packaging • CEC (California Efficiency) • RoHS • WEEE • REACH Package Contents • C7000B cable gateway • Ethernet cable • Quick install guide • Power adapter Data Sheet DOCSIS 3.0 AC1900 Voice and Data Cable Gateway, C7000B C7000B Connection Diagram NETGEAR and the NETGEAR logo are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/ or other countries. Other brand names mentioned herein are for identification purposes only and may be trademarks of their respective holder(s). Information is subject to change without notice. © 2014 NETGEAR, Inc. All rights reserved.D-C7000B-1 Push ‘N’ Connect with WPS WiFi On/Off Voice ports USB 2.0 port Gigabit Ethernet Coaxial Cable Internet † Maximum wireless signal rate derived from IEEE standard 802.11 specifications. Actual data throughput and wireless coverage will vary. Network conditions and environmental factors, including volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate and wireless coverage. NETGEAR makes no express or implied representations or warranties about this product’s compatibility with any future standards. 802.11ac 1300 Mbps is approximately 3x faster than 802.11n 450 Mbps. 2.4GHz Performance Mode requires 256 QAM support on WiFi client. Up to 1300 Mbps wireless speeds achieved when connecting to other 802.11ac 1300 Mbps devices. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this dev…

Text truncated - open the document above for the full version.

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Tel:408-890-3657/Fax:408-907-8097 Date: 2014/11/17 G E N E R A L D E C L A R A T I O N We, NETGEAR, INC. declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non- US channels in all the operational mode(s) for the following product. FCC ID: PY314300285 If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! ------------------------------------------------------ David Kay/ Regulatory Compliance Manager NETGEAR, INC. TEL: 4088903657 FAX: 4089078097 E-mail: [email protected]

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Tel:408-890-3657/Fax:408-907-8097 P O W E R O F A T T O R N E Y Date: 2014/11/17 FCC ID: PY314300285 To whom it may concern: We, the undersigned, hereby authorize Amanda Wu of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Amanda Wu of BV CPS Taoyuan on our behalf shall have the same effect as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to Contact us. Thank you! Sincerely yours, ------------------------------------------------------ David Kay/ Regulatory Compliance Manager NETGEAR, INC. TEL: 4088903657 FAX: 4089078097 E-mail: [email protected]

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Tel:408-890-3657/Fax:408-907-8097 Date: 2014/11/17 FCC ID: PY314300285 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Software Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ------------------------------------------------------ David Kay/ Regulatory Compliance Manager NETGEAR, INC. TEL: 4088903657 FAX: 4089078097 E-mail: [email protected]

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Tel:408-890-3657/Fax:408-907-8097 Federal Communications Commission Authorization and Evaluation Division Date: November 18, 2014 Confidentiality Request FCC ID: PY314300285 Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 180 days in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ------------------------------------------------------ David Kay/ Regulatory Compliance Manager NETGEAR, INC. TEL: 4088903657 FAX: 4089078097 E-mail: [email protected]

Report No. : 141013E03 Page 1 CONSTRUCTION PHOTOS OF EUT Report No. : 141013E03 Page 2 Report No. : 141013E03 Page 17 Adapter : 2AAF042F NA Report No. : 141013E03 Page 18 Report No. : 141013E03 Page 19 Adapter : AD898F20 Report No. : 141013E03 Page 20 Report No. : 141013E03 Page 21 RJ-45 cable (Shielded) RJ-45 cable (Unshielded) Report No. : 141013E03 Page 22 Coaxial cable

SHEET: AUTHOR: TITLE: P/N: REV: THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR WHEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF NETGEAR, INC. REV DESCRIPTION OF REVISION ENG APPD DATE 01AW-13041-011 of 1 M HUMPHREY 14JUL14M HUMPHREYINITIAL DOCUMENT CREATION01 Pantone 877C Black AW, PLBL, C7000 NOTE: 1. REFER TO NETGEAR SPEC. DOC-00093 FOR COLOR TOLERANCES. 2. INK COLOR IS SHOWN TO THE RIGHT. 3. DIE LINES ARE MAGENTA COLOR AND DO NOT PRINT. 4. MAC & SERIAL NUMBERS TO BE PRINTED BY THE ODM. 5. See NTGR DOC-00112 for SN standard. 6. NTGR SN and MAC address barcode to be encoded AIM USS Code39 and include printed characters below barcodes. 7 INSURE COUNTRY OF ORIGIN IS CORRECT. A. IF COUNTRY OF ORIGIN IS PRE-PRINTED, UNHIDE THE APPROPRIATE COUNTRY OF ORIGIN LAYER AND INCLUDE COUNTRY OF ORIGIN ON LABEL. B. IF COUNTRY OF ORIGIN IS POST-PRINTED USING A THERMAL PRINTER (OR EQUIVALENT), OMIT TEXT FROM ARTWORK (USE LAYERS). (Fig. 1) FCC ID: PY314300285 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. EUT Back

Report No. : 141013E03 Page 3 Report No. : 141013E03 Page 4 Report No. : 141013E03 Page 5 Report No. : 141013E03 Page 6 Report No. : 141013E03 Page 7 Report No. : 141013E03 Page 8 Report No. : 141013E03 Page 9 Report No. : 141013E03 Page 10 Report No. : 141013E03 Page 11 Report No. : 141013E03 Page 12 Report No. : 141013E03 Page 13 Report No. : 141013E03 Page 14 Report No. : 141013E03 Page 15 Report No. : 141013E03 Page 16

Report No.: RF141013E03 1 of 147 Report Format Version 5.2.1 FCC TEST REPORT (15.247) REPORT NO.: RF141013E03 MODEL NO.: C7000 FCC ID: PY314300285 RECEIVED: Oct. 13, 2014 TESTED: Oct. 21 to Nov. 13, 2014 ISSUED: Dec. 12, 2014 APPLICANT: NETGEAR, Inc. ADDRESS: 350 East Plumeria Drive San Jose, CA 95134 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF141013E03 2 of 147 Report Format Version 5.2.1 Table of Contents RELEASE CONTROL RECORD .......................................................................................... 5 1. CERTIFICATION ...................................................................................................... 6 2. SUMMARY OF TEST RESULTS .............................................................................. 7 2.1 MEASUREMENT UNCERTAINTY ........................................................................... 8 3. GENERAL INFORMATION ....................................................................................... 9 3.1 GENERAL DESCRIPTION OF EUT ......................................................................... 9 3.2 DESCRIPTION OF TEST MODES ......................................................................... 13 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ......................... 14 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................ 20 3.4 DUTY CYCLE OF TEST SIGNAL ........................................................................... 21 3.5 DESCRIPTION OF SUPPORT UNITS ................................................................... 23 3.6 CONFIGURATION OF SYSTEM UNDER TEST .................................................... 24 4. TEST TYPES AND RESULTS (FOR 2.4GHz, 2.400 ~ 2.4835GHz Band) ............. 25 4.1 CONDUCTED EMISSION MEASUREMENT ......................................................... 25 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT....................................... 25 4.1.2 TEST INSTRUMENTS ........................................................................................... 25 4.1.3 TEST PROCEDURES ............................................................................................ 27 4.1.4 DEVIATION FROM TEST STANDARD .................................................................. 27 4.1.5 TEST SETUP ......................................................................................................... 27 4.1.6 EUT OPERATING CONDITIONS ........................................................................... 28 4.1.7 TEST RESULTS (MODE 1) .................................................................................... 29 4.1.8 TEST RESULTS (MODE 2) .................................................................................... 31 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................. 33 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 33 4.2.2 TEST INSTRUMENTS ........................................................................................... 34 4.2.3 TEST PROCEDURES ............................................................................................ 36 4.2.4 DEVIATION FROM TEST STANDARD .................................................................. 37 4.2.5 TEST SETUP ......................................................................................................... 37 4.2.6 EUT OPERATING CONDITIONS ........................................................................... 37 4.2.7 TEST RESULTS ..................................................................................................... 38 4.3 6dB BANDWIDTH MEASUREMENT ..................................................................... 51 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ................................................... 51 4.3.2 TEST INSTRUMENTS ........................................................................................... 51 4.3.3 TEST PROCEDURE .............................................................................................. 51 4.3.4 DEVIATION FROM TEST STANDARD .................................................................. 51 4.3.5 TEST SETUP ..…

Text truncated - open the document above for the full version.

Report No.: RF141013E03-1 1 of 67 Report Format Version 5.3.0 FCC TEST REPORT (15.407) REPORT NO.: RF141013E03-1 MODEL NO.: C7000 FCC ID: PY314300285 RECEIVED: Oct. 13, 2014 TESTED: Oct. 21 to Nov. 14, 2014 ISSUED: Dec. 12, 2014 APPLICANT: NETGEAR, Inc. ADDRESS: 350 East Plumeria Drive San Jose, CA 95134 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF141013E03-1 2 of 67 Report Format Version 5.3.0 Table of Contents RELEASE CONTROL RECORD .......................................................................................... 4 1. CERTIFICATION ...................................................................................................... 5 2. SUMMARY OF TEST RESULTS .............................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ........................................................................... 7 3. GENERAL INFORMATION ....................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ......................................................................... 8 3.2 DESCRIPTION OF TEST MODES ......................................................................... 12 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ......................... 13 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................ 16 3.4 DUTY CYCLE OF TEST SIGNAL ........................................................................... 17 3.5 DESCRIPTION OF SUPPORT UNITS ................................................................... 18 3.6 CONFIGURATION OF SYSTEM UNDER TEST .................................................... 19 4. TEST TYPES AND RESULTS ................................................................................ 20 4.1 CONDUCTED EMISSION MEASUREMENT ......................................................... 20 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT....................................... 20 4.1.2 TEST INSTRUMENTS ........................................................................................... 20 4.1.3 TEST PROCEDURES ............................................................................................ 22 4.1.4 DEVIATION FROM TEST STANDARD .................................................................. 22 4.1.5 TEST SETUP ......................................................................................................... 22 4.1.6 EUT OPERATING CONDITIONS ........................................................................... 23 4.1.7 TEST RESULTS (MODE 1) .................................................................................... 24 4.1.8 TEST RESULTS (MODE 2) .................................................................................... 26 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................. 28 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 28 4.2.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS .......... 29 4.2.3 TEST INSTRUMENTS ........................................................................................... 30 4.2.4 TEST PROCEDURES ............................................................................................ 32 4.2.5 DEVIATION FROM TEST STANDARD .................................................................. 32 4.2.6 TEST SETUP ......................................................................................................... 33 4.2.7 EUT OPERATING CONDITION ............................................................................. 33 4.2.8 TEST RESULTS ..................................................................................................... 34 4.3 TRANSMIT POWER MEASUREMENT .................................................................. 47 4.3.1 LIMITS OF TRANSMIT POWER MEASUREMENT ............................................... 47 4.3.2 TEST INSTRUMENTS ........................................................................................... 48 4.3.3 TEST PROCEDURE .............................................................................................. 49 4.3.4 DEVIATION F…

Text truncated - open the document above for the full version.

Report No.:RF141013E03-2 1 of 33 Report Format Version 5.2.1 Supplemental “Transmit Simultaneously” Test Report REPORT NO.: RF141013E03-2 MODEL NO.: C7000 FCC ID: PY314300285 RECEIVED: Oct. 13, 2014 TESTED: Oct. 21 to Nov. 12, 2014 ISSUED: Dec. 12, 2014 APPLICANT: NETGEAR, Inc. ADDRESS: 350 East Plumeria Drive San Jose, CA 95134 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.:RF141013E03-2 2 of 33 Report Format Version 5.2.1 Table of Contents RELEASE CONTROL RECORD ......................................................................................................... 3 1. CERTIFICATION .................................................................................................................... 4 2. SUMMARY OF TEST RESULTS ............................................................................................ 5 2.1 MEASUREMENT UNCERTAINTY ......................................................................................... 6 3. GENERAL INFORMATION .................................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ....................................................................................... 7 3.2 TEST MODE APPLICABLITY AND TESTED CHANNEL DETAIL: ...................................... 11 3.3 DESCRIPTION OF SUPPORT UNITS ................................................................................. 13 3.4 CONFIGURATION OF SYSTEM UNDER TEST .................................................................. 14 4. TEST TYPES AND RESULTS .............................................................................................. 15 4.1 CONDUCTED EMISSION MEASUREMENT ....................................................................... 15 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT .................................................... 15 4.1.2 TEST INSTRUMENTS ......................................................................................................... 15 4.1.3 TEST PROCEDURES .......................................................................................................... 17 4.1.4 DEVIATION FROM TEST STANDARD ................................................................................ 17 4.1.5 TEST SETUP ....................................................................................................................... 18 4.1.6 EUT OPERATING CONDITIONS ......................................................................................... 18 4.1.7 TEST RESULTS (MODE 1) .................................................................................................. 19 4.1.8 TEST RESULTS (MODE 2) .................................................................................................. 21 4.2 RADIATED EMISSION MEASURE…

Text truncated - open the document above for the full version.