PY320100484Orbi Pro WiFi 6 Router / Orbi Pro WiFi 6 Satellite

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 36cm between the radiator & your body.

Netgear Incorporated 350 East Plumeria Drive, San Jose, CA 95134, USA Tel:408-890-3657/Fax:408-907-8097 SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 6.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (obsolete) 4.0 5.0 Sep-16-2014 Updated company name & logo (current) 5.0 6.0 Jun-27-2018 Netgear Incorporated 350 East Plumeria Drive, San Jose, CA 95134, USA Tel:408-890-3657/Fax:408-907-8097 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 6.0 Date: 2020/07/28 To: BVCPS, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, _____Netgear Incorporated_____ hereby authorize Bureau Veritas Consumer Product Services, Inc. to act as a Certification Body for certifying for the following project(s): FCC ID: PY320100484 Product Description: Orbi Pro WiFi 6 Router / Orbi Pro WiFi 6 Satellite Model: SXR80/SXS80 Sincerely, ----------------------------------------------------------- David Kay / Regulatory Compliance Director Netgear Incorporated TEL: 4088903657 FAX: 4089078097 E-mail: [email protected]

Netgear Incorporated 350 East Plumeria Drive, San Jose, CA 95134, USA Tel:408-890-3657/Fax:408-907-8097 SCS-F19: Confidentiality Request Letter Page 1 of 3 Rev 6.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (obsolete) 2.0 3.0 Jan-31-2012 Added IC confidentiality letter form (obsolete) 3.0 4.0 March-26-2015 Corrections to STC form. Added reference to KDB (obsolete) 4.0 5.0 Nov-19-2015 Updated company logo (current) 5.0 6.0 Jun-26-2019 Netgear Incorporated 350 East Plumeria Drive, San Jose, CA 95134, USA Tel:408-890-3657/Fax:408-907-8097 SCS-F19: Confidentiality Request Letter Page 2 of 3 Rev 6.0 Date: 2020/07/28 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: PY320100484 Pursuant to sections 0.457 and 0.459 of CFR 47, we respectfully request permanent confidential treatment of the following Exhibits accompanying this application as: - Block Diagram - Schematics - Operational Description - Software Operational Description - Operational Description-Antenna Specification The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ---------------------------------------------------------------- David Kay / Regulatory Compliance Director Netgear Incorporated TEL: 4088903657 FAX: 4089078097 E-mail: [email protected] Netgear Incorporated 350 East Plumeria Drive, San Jose, CA 95134, USA Tel:408-890-3657/Fax:408-907-8097 SCS-F19: Confidentiality Request Letter Page 3 of 3 Rev 6.0 Date: 2020/07/28 To: Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Short Term Confidentiality Request for FCC ID: PY320100484 To Whom It May Concern: Pursuant to sections 0.457 and 0.459 of CFR 47, and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 45 or 180 ■ days; or for a specified date of / / not to exceed 180 days from the Grant Date. See KDB 726920. - User Manual - Internal Photos - External photos - Test Setup photos The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, ---------------------------------------------------------------- David Kay / Regulatory Compliance Director Netgear Incorporated TEL: 4088903657 FAX: 4089078097 E-mail: [email protected]

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Tel:408-890-3657/Fax:408-907-8097 Date: 2020-07-30 FCC ID: PY320100484 A U T H O R I Z A T I O N L E T T E R To Whom It May Concern: NETGEAR, INC. hereby authorizes Andrea Hsia / Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia / Supervisor of BV CPS Taoyuan on NETGEAR, INC.’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------------------------- David Kay/ Regulatory Compliance Director Netgear Incorporated TEL: 4088903657 FAX: 4089078097 E-mail: [email protected]

Reference No.: 200609C14-FCC-1 Page 1 / 13 CONSTRUCTION PHOTOS OF EUT Reference No.: 200609C14-FCC-1 Page 2 / 13 Model: SXR80 Reference No.: 200609C14-FCC-1 Page 3 / 13 Reference No.: 200609C14-FCC-1 Page 4 / 13 Reference No.: 200609C14-FCC-1 Page 5 / 13 Reference No.: 200609C14-FCC-1 Page 6 / 13 Model: SXS80 Reference No.: 200609C14-FCC-1 Page 7 / 13 Reference No.: 200609C14-FCC-1 Page 8 / 13 Reference No.: 200609C14-FCC-1 Page 9 / 13 Reference No.: 200609C14-FCC-1 Page 10 / 13 Reference No.: 200609C14-FCC-1 Page 11 / 13 Reference No.: 200609C14-FCC-1 Page 12 / 13 Reference No.: 200609C14-FCC-1 Page 13 / 13

FCC ID: PY320100484 Label location At the bottom

Reference No.: 200609C14-FCC-2 Page 1 / 11 CONSTRUCTION PHOTOS OF EUT Ant. 8 (5GH_0) Ant. 5 (5GH_3) Ant. 6 (5GH 2) Ant. 7 (5GH_1) Ant. 4 (2G 3, 5GL 2) Ant. 2 (2G_4, 5GL_1) Ant. 1 (2G_1, 5GL_3)Ant. 3 (2G_2, 5GL_4) Reference No.: 200609C14-FCC-2 Page 2 / 11 Reference No.: 200609C14-FCC-2 Page 3 / 11 Reference No.: 200609C14-FCC-2 Page 4 / 11 Reference No.: 200609C14-FCC-2 Page 5 / 11 Reference No.: 200609C14-FCC-2 Page 6 / 11 Reference No.: 200609C14-FCC-2 Page 7 / 11 Reference No.: 200609C14-FCC-2 Page 8 / 11 Reference No.: 200609C14-FCC-2 Page 9 / 11 Reference No.: 200609C14-FCC-2 Page 10 / 11 Reference No.: 200609C14-FCC-2 Page 11 / 11

Report No.: SA200609C14 Page No. 1 / 6 Report Format Version: 6.1.1 RF Exposure Report Report No.: SA200609C14 FCC ID: PY320100484 Test Model: SXR80 Series Model: SXS80 Received Date: Jun. 09, 2020 Test Date: Jul. 01 ~ Jul. 05, 2020 Issued Date: Jul. 16, 2020 Applicant: NETGEAR, INC. Address: 350 East Plumeria Drive, San Jose, CA 95134, USA Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SA200609C14 Page No. 2 / 6 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 3 Calculation Result of Maximum Conducted Power ........................................................................... 6 Report No.: SA200609C14 Page No. 3 / 6 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SA200609C14 Original release Jul. 16, 2020 Report No.: SA200609C14 Page No. 4 / 6 Report Format Version: 6.1.1 1 Certificate of Conformity Product: Orbi Pro WiFi 6 Router / Orbi Pro WiFi 6 Satellite Brand: NETGEAR Test Model: SXR80 Series Model: SXS80 Sample Status: Engineering sample Applicant: NETGEAR, INC. Test Date: Jul. 01 ~ Jul. 05, 2020 Standards: FCC Part 2 (Section 2.1091) References Test Guidance: KDB 447498 D01 General RF Exposure Guidance v06 IEEE C95.3 -2002 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date:Jul. 16, 2020 Pettie Chen / Senior Specialist Approved by : , Date:Jul. 16, 2020 Bruce Chen / Senior Project Engineer Report No.: SA200609C14 Page No. 5 / 6 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 f = Frequency in MHz; *Plane-wave equivalent power density 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 36cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA200609C14 Page No. 6 / 6 Report Format Version: 6.1.1 3 Calculation Result of Maximum Conducted Power Frequency Band (MHz) Max Average Power (dBm) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) CDD Mode 2412-2462 29.79 6.81 36 0.281 1 5180-5240 29.56 7.56 36 0.316 1 5745-5825 29.90 7.88 36 0.368 1 Beamforming Mode 2412-2462 29.17 6.81 36 0.243 1 5180-5240 28.41 7.56 36 0.243 1 5745-5825 28.10 7.88 36 0.243 1 *Determining compliance based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. Note: The above Max Power is Tune-up Power which client declaried. Conclusion: The formula of calculated the MPE is: CPD1 / LPD1 + CPD2 / LPD2 + ......etc. < 1 CPD = Calculation power density LPD = Limit of power density 2412-2462 MHz + 5180-5240 MHz + 5745-582…

Text truncated - open the document above for the full version.

Report No.: RF200609C14-1 Page No. 1 / 79 Report Format Version:6.1.2 FCC Test Report Report No.: RF200609C14-1 FCC ID: PY320100484 Test Model: SXR80 Series Model: SXS80 Received Date: Jun. 09, 2020 Test Date: Jul. 01 ~ Jul. 10, 2020 Issued Date: Jul. 16, 2020 Applicant: NETGEAR, INC. Address: 350 East Plumeria Drive, San Jose, CA 95134, USA Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location (1): No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number(1): 788550 / TW0003 Test Location (2): E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan. FCC Registration / Designation Number(2): 723255 / TW2022 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RF200609C14-1 Page No. 2 / 79 Report Format Version:6.1.2 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................... 9 3.2.1 Test Mode Applicability and Tested Channel Detail ........................................................................... 10 3.3 Duty Cycle of Test Signal .................................................................................................................. 12 3.4 Description of Support Units ............................................................................................................. 13 3.4.1 Configuration of System under Test .................................................................................................. 13 3.5 General Description of Applied Standards ........................................................................................ 14 4 Test Types and Results ...................................................................................................................... 15 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 15 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 15 4.1.2 Test Instruments ................................................................................................................................ 16 4.1.3 Test Procedures ................................................................................................................................. 17 4.1.4 Deviation from Test Standard ............................................................................................................ 17 4.1.5 Test Setup .......................................................................................................................................... 18 4.1.6 EUT Operating Conditions ................................................................................................................. 19 4.1.7 Test Results ....................................................................................................................................... 20 4.2 Conducted Emission Measurement .................................................................................................. 40 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 40 4.2.2 Test Instruments ................................................................................................................................ 40 4.2.3 Test Procedures .............................................................................................................................…

Text truncated - open the document above for the full version.

Report No.: RF200609C14-2 Page No. 1 / 26 Report Format Version: 6.1.1 FCC Test Report (Co-Located) Report No.: RF200609C14-2 FCC ID: PY320100484 Test Model: SXR80 Series Model: SXS80 Received Date: Jun. 09, 2020 Test Date: Jul. 01 ~ Jul. 05, 2020 Issued Date: Jul. 16, 2020 Applicant: NETGEAR, INC. Address: 350 East Plumeria Drive, San Jose, CA 95134, USA Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location (1): No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number(1): 788550 / TW0003 Test Location (2): E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan. FCC Registration / Designation Number(2): 723255 / TW2022 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RF200609C14-2 Page No. 2 / 26 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes ................................................................................................................... 9 3.2.1 Test Mode Applicability and Tested Channel Detail ........................................................................... 10 3.3 Description of Support Units .............................................................................................................. 11 3.3.1 Configuration of System under Test .................................................................................................. 12 3.4 General Description of Applied Standards ........................................................................................ 12 4 Test Types and Results ...................................................................................................................... 13 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 13 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 13 4.1.2 Test Instruments ................................................................................................................................ 14 4.1.3 Test Procedures ................................................................................................................................. 15 4.1.4 Deviation from Test Standard ............................................................................................................ 15 4.1.5 Test Setup .......................................................................................................................................... 16 4.1.6 EUT Operating Conditions ................................................................................................................. 17 4.1.7 Test Results ....................................................................................................................................... 18 4.2 Conducted Emission Measurement .................................................................................................. 21 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 21 4.2.2 Test Instruments ................................................................................................................................ 21 4.2.3 Test Procedures ................................................................................................................................. 22 4.2.4 Deviation from Test Standard .........................................................................................…

Text truncated - open the document above for the full version.

Reference No.: 200609C14 Page No. 1 / 4 PHOTOGRAPHS OF THE TEST CONFIGURATION Conducted Emission Test Reference No.: 200609C14 Page No. 2 / 4 Radiated Emission Test (Above 1GHz) Reference No.: 200609C14 Page No. 3 / 4 Reference No.: 200609C14 Page No. 4 / 4 Radiated Emission Test (Below 1GHz)