PY322200565AXE3000 USB3.0 Wireless Adapter

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FOR PORTABLE DEVICE USAGE (<20m from body/SAR needed) Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. FOR COUNTRY CODE SELECTION USAGE (WLAN DEVICES) Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. For 6XD (Indoor Client) Prohibited for control of or communications with unmanned aircraft systems, including drones. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 5 mm must be maintained between the user’s body and EUT dongle.

Quick Start March 2022 Package contents WiFi USB adapter Desktop dock Wireless AXE3000 WiFi 6/6E USB 3.0 Adapter Model A8000 Support and Community Visit netgear.com/support to get your questions answered and access the latest downloads. You can also check out our NETGEAR Community for helpful advice at community.netgear.com. Regulatory and Legal Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français canadien à https://www.netgear.com/support/download/. (If this product is sold in Canada, you can access this document in Canadian French at https://www.netgear.com/support/download/.) For regulatory compliance information including the EU Declaration of Conformity, visit https://www.netgear.com/about/regulatory/. See the regulatory compliance document before connecting the power supply. For NETGEAR’s Privacy Policy, visit https://www.netgear.com/about/privacy-policy. By using this device, you are agreeing to NETGEAR’s Terms and Conditions at https://www.netgear.com/about/terms- and-conditions. If you do not agree, return the device to your place of purchase within your return period. Applicable to 6 GHz devices only: Only use the device indoors. The operation of 6 GHz devices is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet. Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems. © NETGEAR, Inc., NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non-NETGEAR trademarks are used for reference purposes only. NETGEAR, Inc. 350 East Plumeria Drive San Jose, CA 95134, USA NETGEAR INTERNATIONAL LTD Floor 1, Building 3 University Technology Centre Curraheen Road, Cork, T12EF21, Ireland Install the Windows standalone driver The Windows standalone driver allows you to use your computer’s built-in Windows WiFi network settings to connect the adapter to a WiFi network. 1. Visit https://www.netgear.com/support/ download/?model=A8000 and download the latest software file for Windows. 2. Extract the files from the .zip file. 3. Double-click the file that ends in.exe and includes Standalone in the file name. 4. Follow the prompts to complete installation. Insert the adapter You can connect your adapter to your computer’s USB port with or without the desktop dock: • With the desktop dock: Place the adapter into the desktop dock and connect the USB cable to the USB port on your computer. When the adapter is placed in the desktop dock, you can fold out the adapter to its maximum angle for increased WiFi performance. Do not use another USB cable to connect the adapter to the USB port on your computer. Using another USB cable might affect the performance of your adapter. Use the desktop dock with the attached cable that is supplied in the package. • Without the desktop dock: Insert the adapter into a USB port on your computer. Join a WiFi network 1. Make sure the Windows standalone driver is installed on your computer. 2. Insert the adapter into a USB port on your computer. 3. Open the WiFi network settings on your computer and select a WiFi network to connect. For more information about how to connect to a WiFi network using your computer, see the Microsoft Windows support site.

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Date: July 22, 2022 We, Netgear Incorporated, declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. FCC ID: PY322200565 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- David Kay, Regulatory Compliance Director NETGEAR, INC. Tel: 4088903657 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Date: 2022-08-08 FCC ID: PY322200565 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description Software Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- David Kay, Regulatory Compliance Director NETGEAR, INC. Tel: +1-408-890-3657 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Date: 2022-07-22 FCC ID: PY322200565 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: ⚫ External photos ⚫ Test Setup photos ⚫ User’s manual ⚫ Internal Photos Sincerely yours, ----------------------------------- David Kay, Regulatory Compliance Director NETGEAR, INC. Tel: 4088903657 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Date: 2022-07-22 FCC ID: PY322200565 A U T H O R I Z A T I O N L E T T E R To Whom It May Concern: Netgear Incorporated hereby authorizes Trista TSAI / Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Trista TSAI / Specialist of BV CPS Taoyuan on Netgear Incorporated’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------------------- David Kay, Regulatory Compliance Director NETGEAR, INC. Tel: 4088903657 Fax: 4089078097 E-mail: [email protected]

Reference No.: BBQZ-WTW-P22030481_EXT Page No. 1 / 5 CONSTRUCTION PHOTOS OF EUT Reference No.: BBQZ-WTW-P22030481_EXT Page No. 2 / 5 Reference No.: BBQZ-WTW-P22030481_EXT Page No. 3 / 5 Reference No.: BBQZ-WTW-P22030481_EXT Page No. 4 / 5 Reference No.: BBQZ-WTW-P22030481_EXT Page No. 5 / 5

Label Sample & Label Location FCC ID: PY322200565 The label will be permanently affixed and readily visible. Label location

Reference No.: BBQZ-WTW-P22030481_INT Page No. 1 / 7 CONSTRUCTION PHOTOS OF EUT Reference No.: BBQZ-WTW-P22030481_INT Page No. 2 / 7 Reference No.: BBQZ-WTW-P22030481_INT Page No. 3 / 7 Reference No.: BBQZ-WTW-P22030481_INT Page No. 4 / 7 Reference No.: BBQZ-WTW-P22030481_INT Page No. 5 / 7 Reference No.: BBQZ-WTW-P22030481_INT Page No. 6 / 7 Reference No.: BBQZ-WTW-P22030481_INT Page No. 7 / 7

Report No.: MFBBQZ-WTW-P22030481 Page No. 1 / 6 Report Format Version: 6.1.1 RF Exposure Report Report No.: MFBBQZ-WTW-P22030481 FCC ID: PY322200565 Test Model: A8000 Received Date: Mar. 14, 2022 Test Date: Jul. 08 ~ Jul. 30, 2022 Issued Date: Aug. 09, 2022 Applicant and Manufacturer: NETGEAR, INC. Address: 350 East Plumeria Drive, San Jose, CA 95134, USA Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: MFBBQZ-WTW-P22030481 Page No. 2 / 6 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 3 Calculation Result of Maximum Conducted Power ........................................................................... 6 Report No.: MFBBQZ-WTW-P22030481 Page No. 3 / 6 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued MFBBQZ-WTW-P22030481 Original release Aug. 09, 2022 Report No.: MFBBQZ-WTW-P22030481 Page No. 4 / 6 Report Format Version: 6.1.1 1 Certificate of Conformity Product: AXE3000 USB3.0 Wireless Adapter Brand: Netgear Test Model: A8000 Sample Status: Engineering sample Applicant and Manufacturer: NETGEAR, INC. Test Date: Jul. 08 ~ Jul. 30, 2022 FCC Rule Part: FCC Part 2 (Section 2.1091) Standards: KDB 447498 D01 General RF Exposure Guidance v06 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date:Aug. 09, 2022 Polly Chien / Specialist Approved by : , Date:Aug. 09, 2022 Jeremy Lin / Project Engineer Report No.: MFBBQZ-WTW-P22030481 Page No. 5 / 6 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 f = Frequency in MHz; *Plane-wave equivalent power density 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: MFBBQZ-WTW-P22030481 Page No. 6 / 6 Report Format Version: 6.1.1 3 Calculation Result of Maximum Conducted Power Frequency Band (MHz) Max AV Power (dBm) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) 2412-2462 15.99 2.20 20 0.013 1 5180-5240 16.91 2.30 20 0.017 1 5260-5320 16.99 2.80 20 0.019 1 5500-5720 16.98 2.70 20 0.018 1 5745-5825 16.78 2.60 20 0.017 1 Frequency Band (MHz) EIRP (dBm) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) NSS 1 5955-6415 15.76 20 0.007 1 …

Text truncated - open the document above for the full version.

SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 33 Report No. : SFBBQZ-WTW-P22030481 Issued Date : Aug. 03, 2022 SAR & Power Density Test Report Report No. : SFBBQZ-WTW-P22030481 Applicant and Manufacturer : NETGEAR, INC. Address : 350 East Plumeria Drive San Jose CA 95134 Product : AXE3000 USB3.0 Wireless Adapter FCC ID : PY322200565 Brand : Netgear Model No. : A8000 FCC Rule Part : CFR §2.1093 Standards : IEEE C95.1:1992, IEC/IEEE 66209-1528:2020, IEC TR 63170:2018 KDB 865664 D01 v01r04, KDB 865664 D02 v01r02, KDB 248227 D01 v02r02, KDB 447498 D01 v06, KDB 447498 D02 v02r01 Sample Received Date : Mar. 14, 2022 Date of Testing : Jul. 11, 2022 ~ Jul. 19, 2022 Lab Address : No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location : No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City, Taiwan CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch–Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Vera Huang / Specialist Approved By : Gordon Lin / Manager FCC Accredited No.: TW0003 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our- business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 33 Report No. : SFBBQZ-WTW-P22030481 Issued Date : Aug. 03, 2022 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR and Power Density Value ...................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 6 3.2 SPEAG DASY6 System ............................................................................................................................................... 6 3.2.1 Robot.................................................................................................................................................................. 7 3.2.2 Probes ................................................................................................................................................................ 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................... 8 3.2.4 Phantoms ........................................................................................................................................................... 8 3.2.5 Device Holder ..................................................................................................................................................... 9 3.2.6 System Validation Dipoles ................................................................................................................................ 10 3.2.7 Power Source ................................................................................................................................................... 10 3.2.8 Tissue Simulating Liquids ................................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 13 3.4 SAR Measurement Procedure ........................................................…

Text truncated - open the document above for the full version.

Plots of System Verification Annex A. Plots of System Verification The plots for system verification are shown as follows. Report No.: SFBBQZ-WTW-P22030481 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/7/11 S01 System Check_H2450_220711 DUT: Dipole 2450 MHz; Type: D2450V2; SN: 737 Communication System: UID 0, CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: H19T27N1_0711 Medium parameters used (interpolated): f = 2450 MHz; σ = 1.88 S/m; ε r = 38.883; ρ = 1000 kg/m 3 Ambient Temperature：23.2 °C ; Liquid Temperature：23.1 °C DASY5 Configuration: - Probe: EX3DV4 - SN7736; ConvF(8.12, 8.12, 8.12) @ 2450 MHz; Calibrated: 2022/5/30 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579; Calibrated: 2022/6/1 - Phantom: SAM Phantom_1987; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7501) Pin=50mW/Area Scan (81x81x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 4.29 W/kg Pin=50mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 49.09 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 5.39 W/kg SAR(1 g) = 2.48 W/kg; SAR(10 g) = 1.18 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 4.26 W/kg Report No.: SFBBQZ-WTW-P22030481 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/07/12 S02 System Check_H5250_220712 DUT: Dipole 5 GHz; Type: D5GHzV2; SN: 1019 Communication System: UID 0, CW; Frequency: 5250 MHz;Duty Cycle: 1:1 Medium: H34T60N1_0712 Medium parameters used: f = 5250 MHz; σ = 4.704 S/m; ε r = 36.205; ρ = 1000 kg/m 3 Ambient Temperature：23.4 °C ; Liquid Temperature：23.3 °C DASY5 Configuration: - Probe: EX3DV4 - SN3650; ConvF(5.28, 5.28, 5.28) @ 5250 MHz; Calibrated: 2022/03/24 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn861; Calibrated: 2022/03/23 - Phantom: SAM Phantom_1985; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7501) Pin=50mW/Area Scan (91x91x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 9.61 W/kg Pin=50mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 47.27 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 15.8 W/kg SAR(1 g) = 4.01 W/kg; SAR(10 g) = 1.14 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 10.0 W/kg Report No.: SFBBQZ-WTW-P22030481 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/07/12 S03 System Check_H5600_220712 DUT: Dipole 5 GHz; Type: D5GHzV2; SN: 1019 Communication System: UID 0, CW; Frequency: 5600 MHz;Duty Cycle: 1:1 Medium: H34T60N1_0712 Medium parameters used: f = 5600 MHz; σ = 4.997 S/m; ε r = 35.803; ρ = 1000 kg/m 3 Ambient Temperature：23.4 °C ; Liquid Temperature：23.3 °C DASY5 Configuration: - Probe: EX3DV4 - SN3650; ConvF(4.78, 4.78, 4.78) @ 5600 MHz; Calibrated: 2022/03/24 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn861; Calibrated: 2022/03/23 - Phantom: SAM Phantom_1985; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7501) Pin=50mW/Area Scan (91x91x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 10.5 W/kg Pin=50mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 47.17 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 18.1 W/kg SAR(1 g) = 4.19 W/kg; SAR(10 g) = 1.18 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 10.9 W/kg Report No.: SFBBQZ-WTW-P22030481 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/07/12 S04 System Check_H5750_220712 DUT: Dipole 5 GHz; Type: D5GHzV2; SN: 1019 Communication System: UID 0, CW; Frequency: 5750 MHz;Duty Cycle: 1:1 Medium: H34T60N1_0712 Medium parameters used: f = 5750 MHz; σ = 5.255 S/m; ε r = 35.49; ρ = 1000 kg/m 3 Ambient Temperature：23.4 °C ; Liquid Temperature：23.3 °C DASY5 Configuration: - Probe: EX3DV4 - SN3650; ConvF(5.06, 5.06, 5.06) @ 5750 MHz; Calibrated: 2022/03/24 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn861; Calibrated: 2022/03/23 - Phantom: SAM Phantom_1985; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7501) Pin=50mW/Area Scan (91x91x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 9.26 W/kg Pin=50mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 47.29 V/m; Power Drift = -0.01 dB Peak SAR (extrapolated) = 16.8 W/kg SAR(1 g) = 3.71 W/kg; SAR(10 g) = 1.05 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 9.82 W/kg Report No.: SFBBQZ-WTW-P22030481 Plots of System Verification Measurement Report S05 SAR-System Check_H6500_220718 Device under Test Properties Model, Manufacturer Dimensions [mm] IMEI DUT Type Dipole, 50.0 x 10.0 x 8.0 6500 Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] Band Group, UID Frequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Flat, HSL , , 6500.0, 5.7 6.08 34.6 Hardware Setup Phantom TSL, Measured Date Probe, Calibration Date DAE, Calibration Date Twin-SAM V8.0 (30deg probe tilt) - 1987 H50T72N1, 2022-Jul-18 EX3DV4 - SN7736, 2022-05-30 DAE3 Sn579, 2022-06-01 Scan Setup Area Scan Zoom Scan Grid Extents [mm] 45.0 x 90.0 22.0 x 22.0 x 22.0 Grid Steps [mm] 7.5 x 7.5 3.4 x 3.4 x 1.4 Sensor Surface [mm] 3.0 1.4 Measurement Results Area Scan Zoom Scan Date 2022-07-18 2022-07-18 psSAR1g [W/kg] 24.3 28.4 psSAR10g [W/kg] 4.79 5.20 psPDab (1.0cm2, sq) [W/m2] 284 psPDab (4.0cm2, sq) [W/m2] 127 Power Drift [dB] 0.00 -0.02 M2/M1 [%] 51.7 Dist 3dB Peak [mm] 4.6 Report No.: SFBBQZ-WTW-P22030481 Plots of System Verification Measurement Report S05 Powe…

Text truncated - open the document above for the full version.

Annex Z. Calibration Certificate for Probe and Dipole The SPEAG calibration certificates are shown as follows. Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Model：D5000V2S/N：1019Measurement Date：2022/3/18 Frequency (MHz) Type Item Previous Measurement Annual Check Deviation Accepted Tolerance Result Real Impedance 54.12650.625-3.501±5ΩPASS Imaginary Impedance -6.4286-1.52384.905±5ΩPASS Return Loss -22.708-21.152-6.85%±20%PASS Frequency (MHz) Type Item Previous Measurement Annual Check Deviation Accepted Tolerance Result Real Impedance 57.60253.069-4.533±5ΩPASS Imaginary Impedance -2.47611.19363.670±5ΩPASS Return Loss -22.582-22.463-0.53%±20%PASS Frequency (MHz) Type Item Previous Measurement Annual Check Deviation Accepted Tolerance Result Real Impedance 57.87653.895-3.981±5ΩPASS Imaginary Impedance 3.12310.0377-3.085±5ΩPASS Return Loss -22.102-21.278-3.73%±20%PASS 5750 Free Space 5000 MHz，Free Space Annual Confirmation of SAR Reference Dipole 5250 Free Space 5600 Free Space Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-P22030481 Report No.: SFBBQZ-WTW-…

Text truncated - open the document above for the full version.