PY322300569WiFi 6 AX1800 Dual Band Access Point

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FOR MOBILE DEVICE USAGE (>20cm/low power) Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FOR UNII-4 (Indoor AP) FCC regulations restrict the operation of this device to indoor use only

NETGEAR, Inc. 350 East Plumeria Drive San Jose, CA 95134, USA Mounting plate © NETGEAR, Inc., NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non‑NETGEAR trademarks are used for reference purposes only. September 2022 NETGEAR INTERNATIONAL LTD Floor 1, Building 3, University Technology Centre Curraheen Road, Cork, T12EF21, Ireland Essentials WiFi 6 AX1800 Dual Band Access Point Model WAX214v2 Installation Guide Power up the WAX214v2 access point (AP) using one of the following methods: • Use a PoE+ switch: Connect one end of an Ethernet cable to the LAN/PoE+ port of the AP and connect the other end to a PoE+ switch that supplies 802.3at PoE+ power. The power LED on the AP lights. • Use a power adapter: Connect the power adapter’s DC plug to the AP, and insert the power adapter in a power outlet. The power LED on the AP lights. Then, connect one end of an Ethernet cable to the LAN/PoE+ port of the AP, and connect the other end to a switch or a router. 55 Access Point Model WAX214v2 Package contents Overview Start Here: Step 1. Connect the WAX214v2 to your network 1 Power LED 2 LAN LED 3 2.4 GHz WLAN LED 4 5 GHz WLAN LED 12 3 4 WA X214v2 Sample connections RouterInternet PoE+ switch (model GS310TP) WiFi clients 1. Connect your computer or tablet to the AP’s management WiFi network (SSID) using one of the following methods: • Scan the QR code: Scan the QR code on the AP label to connect to the management WiFi network. • Connect manually: The management WiFi network is on the AP label. The default network key (password) for WiFi access is also on the AP label. The default name of the management WiFi network is printed on the AP’s label. The WiFi network name uses the format “WAX214XXXXXX‑CONFIG‑ONLY,” where XXXXXX is customized to every device (based on the last six digits of the MAC address). 2. Launch a web browser and enter https://www.aplogin.net in the address field. Use https, not http. Note that https://www.aplogin.net is the same as https://192.168.0.100. NOTE: • Your browser might display a security warning because of the self-signed certificate on the AP, which is expected behavior. You can proceed, or add an exception for the security warning. For more information, see kb.netgear.com/000062980/. • If your browser redirects to a www.netgear.com page, your computer or tablet is not connected to the AP’s management WiFi network, and you must repeat the previous step. The Welcome page for the setup process displays. 3. Click the Next button. 4. Set a new AP login password, and for your first user WiFi network, set a WiFi network name and password. 5. Click the Apply button. Your settings are saved and the AP restarts. This process takes about two minutes. You are done. The AP is connected to the network and ready to use. You can now connect a computer or mobile device to the user WiFi network that you just set up, using the WiFi password that you just defined. For more information, including information about how to log in to the AP’s device UI to change the AP’s settings and update the firmware, see the user manual, which you can download by visiting netgear.com/support/download and entering WAX214v2 in the search field. Step 2. Set up Internet access and connect 5 During installation and setup, the AP’s LEDs can light in these colors: PowerSolid amber: The AP is starting up. If the LED remains solid amber, the PoE power is not at the required 802.3at (PoE+) level. Blinking amber: The firmware is being updated, or the AP cannot detect a DHCP server. Solid green: The AP is powered on and ready. LAN Solid or blinking green: The LAN port detects a 1 Gbps link with a powered‑on device. Solid or blinking amber: The LAN port detects a 100 Mbps or 10 Mbps link with a powered‑on device. 2.4 GHz WLAN Solid green: The 2.4 GHz radio is operating without clients. Solid or blinking blue: The 2.4 GHz radio is operating with clients 5 GHz WLAN Solid green: The 5 GHz radio is operating without clients. Solid or blinking blue: The 5 GHz radio is operating with clients. NOTE: For security reasons, the management WiFi network turns off when inactive for 15 minutes. If this happens during setup, press the Reset button for 20 seconds to reset the AP to default settings. When you power up your new AP, the management WiFi network becomes active. We recommend that you use a WiFi‑enabled computer or tablet to connect to the management WiFi network for setup. NOTE: The AP supports two types of WiFi networks (SSIDs): • Management WiFi network: The special purpose WiFi network that you use to access the AP’s device UI to configure and manage the AP. You can use the QR code or WiFi network information on the AP label to connect to the management WiFi network. To protect your WiFi network security, the management WiFi network does not let you connect to the Internet. • User WiFi network: The WiFi network that provides general network access to authenticated users. During set up, you must configure the first user WiFi network. After you complete the initial setup process, you can configure up to three additional WiFi networks. 2 Phillips head screws and anchors for mounting Metal bracket with T‑bar, lock screw, and 4 short screws 5 7 5 DC power connector 6 Reset button 7 LAN/PoE+ port 6 NOTE: WiFi and wireless have the same meaning. Power adapter is included only with a WAX214PA SKU. NOTE: You can power up the WAX214v2 by connecting it to a PoE switch or to a power adapter. If you purchased a WAX214 SKU without an included power adapter, you can purchase one separately. Visit netgear.com/support to get your questions answered and access the latest downloads. You can also check out our NETGEAR Community for helpful advice at community.netgear.com. Support and Community Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français canadien à https://www.netgear.com/support/download/. (If this product is sold in Canada, you can access this document in Canadian French at https:// ww…

Text truncated - open the document above for the full version.

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Date: September 26, 2022 We, Netgear Incorporated, declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. FCC ID: PY322300569 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- David Kay, Regulatory Compliance Director NETGEAR, INC. Tel: 4088903657 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Date: 2022-09-26 FCC ID: PY322300569 Declaration for DFS master devices We, Netgear Incorporated hereby declare that the device meets all the other requirements specified in Part 15E Section 15.407. If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- David Kay, Regulatory Compliance Director NETGEAR, INC. Tel: 4088903657 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Date: 2022-09-26 FCC ID: PY322300569 To the attention of: Federal Communications Commission Authorization and Evaluation Division Declaration Letter for Indoor Access Points We, Netgear Incorporated, attest that this device under FCC ID: PY322300569 complies with device protocol requirements and operational restrictions for Indoor Access Point Devices. a) This indoor access point to control the associated client/subordinate devices, allowing it to transmit without receiving an enabling signal. This mode can select a channel and initiate a network by sending enabling signals to client devices and subordinate devices. b) This Indoor Access Point operates in the 5.850-5.895 GHz band. It is supplied power from a wired connection, has an integrated antenna, is not battery-powered, and does not have a weatherized enclosure. c) We acknowledge this device is subject to and in full compliance with the device restrictions listed below. All users are notified of these restrictions through the user manual. • Access Point operating in the 5.850-5.895 GHz band shall be supplied power from a wired connection, has an integrated antenna, is not battery powered, and does not have a weatherized enclosure. • This device's operation will not be allowed on cars, trains, boats, and aircraft, except that low power indoor devices and associated client devices can operate on large aircraft above 10,000 feet. • A statement in a conspicuous location on the device and the user's manual: “FCC regulations restrict the operation of this device to indoor use only.” & Section 15.19 Statement (if not on the device) If you should have any questions regarding this declaration, please do not hesitate to contact us, thank you! Sincerely yours, ----------------------------------- David Kay, Regulatory Compliance Director NETGEAR, INC. Tel: 4088903657 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Date: 2022-09-26 FCC ID: PY322300569 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description Software Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- David Kay, Regulatory Compliance Director NETGEAR, INC. Tel: 4088903657 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Date: 2022-09-26 FCC ID: PY322300569 Declaration Letter We, Netgear Incorporated, declare that the device will enable only WLAN 2.4G & 5G function through the applicant’s proprietary firmware and is not user changeable. If you have any questions regarding the authorization, please do not hesitate to contact us. Thank you! ----------------------------------- David Kay, Regulatory Compliance Director Netgear Incorporated Tel: 4088903657 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 350 East Plumeria Drive, San Jose, CA 95134, USA Date: 2022-09-26 FCC ID: PY322300569 A U T H O R I Z A T I O N L E T T E R To Whom It May Concern: Netgear Incorporated hereby authorizes Trista TSAI / Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Trista TSAI / Specialist of BV CPS Taoyuan on Netgear Incorporated’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------------------- David Kay, Regulatory Compliance Director NETGEAR, INC. Tel: 4088903657 Fax: 4089078097 E-mail: [email protected]

Reference No.: BBQZ-WTW-P22060184_FCC_EXT Page 1/10 CONSTRUCTION PHOTOS OF EUT Reference No.: BBQZ-WTW-P22060184_FCC_EXT Page 2/10 Reference No.: BBQZ-WTW-P22060184_FCC_EXT Page 3/10 Reference No.: BBQZ-WTW-P22060184_FCC_EXT Page 4/10 Reference No.: BBQZ-WTW-P22060184_FCC_EXT Page 5/10 Reference No.: BBQZ-WTW-P22060184_FCC_EXT Page 6/10 Reference No.: BBQZ-WTW-P22060184_FCC_EXT Page 7/10 Reference No.: BBQZ-WTW-P22060184_FCC_EXT Page 8/10 Reference No.: BBQZ-WTW-P22060184_FCC_EXT Page 9/10 Reference No.: BBQZ-WTW-P22060184_FCC_EXT Page 10/10

FCC ID: PY322300569 Label Location

Reference No.: BBQZ-WTW-P22060184_INT Page 1/8 CONSTRUCTION PHOTOS OF EUT Reference No.: BBQZ-WTW-P22060184_INT Page 2/8 Reference No.: BBQZ-WTW-P22060184_INT Page 3/8 Reference No.: BBQZ-WTW-P22060184_INT Page 4/8 Reference No.: BBQZ-WTW-P22060184_INT Page 5/8 Reference No.: BBQZ-WTW-P22060184_INT Page 6/8 Reference No.: BBQZ-WTW-P22060184_INT Page 7/8 Reference No.: BBQZ-WTW-P22060184_INT Page 8/8

Report No.: MFBBQZ-WTW-P22060184 Page No. 1 / 12 Report Format Version: 7.1.0 RF EXPOSURE REPORT CERTIFICATE OF CONFORMITY FCC Rule Part: FCC Part 2 (Section 2.1091) Report No.: MFBBQZ-WTW-P22060184 FCC ID: PY322300569 Model No.: WAX214v2 Received Date: 2022/6/8 Test Date: 2022/9/22 Issued Date: 2022/10/3 Applicant: NETGEAR, INC. Address: 350 East Plumeria Drive San Jose CA 95134 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kewi Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 Approved by: , Date:2022/10/3 Jeremy Lin / Project Engineer This test report consists of 12 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. Prepared by : Celine Chou / Senior Specialist This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our- business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: MFBBQZ-WTW-P22060184 Page No. 2 / 12 Report Format Version: 7.1.0 Table of Contents Release Control Record ....................................................................................................................................................... 3 1 Certificate .................................................................................................................................................................... 4 2 Applicable RF Exposure Limit .................................................................................................................................. 5 3 Applicable Evaluation Criteria .................................................................................................................................. 6 3.1 RF Exposure ............................................................................................................................................................. 7 4 Test Results ................................................................................................................................................................ 9 4.1 RF Exposure ............................................................................................................................................................. 9 5 Conclusion ................................................................................................................................................................ 11 6 Information of the Testing Laboratories ................................................................................................................ 12 Report No.: MFBBQZ-WTW-P22060184 Page No. 3 / 12 Report Format Version: 7.1.0 Release Control Record Issue No. Description Date Issued MFBBQZ-WTW-P22060184 Original release. 2022/10/3 Report No.: MFBBQZ-WTW-P22060184 Page No. 4 / 12 Report Format Version: 7.1.0 1 Certificate Product: WiFi 6 AX1800 Dual Band Access Point Brand: NETGEAR Test Model: WAX214v2 Sample Status: Engineering sample Applicant: NETGEAR, INC. Test Date: 2022/9/22 FCC Rule Part: FCC Part 2 (Section 2.1091) Standard: KDB 447498 D04 Interim General RF Exposure Guidance v01 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Report No.: MFBBQZ-WTW-P22060184 Page No. 5 / 12 Report Format Version: 7.1.0 2 Applicable RF Exposure Limit § 1.1310 Radiofrequency radiation exposure limits. (a) Specific absorption rate (SAR) shall be used to evaluate the environmental impact of human exposure to radiofrequency (RF) radiation as specified in § 1.1307(b) of this part within the frequency range of 100 kHz to 6 GHz (inclusive). (b) The SAR limits for occupational/controlled exposure are 0.4 W/kg, as averaged over the whole body, and a peak spatialaverage SAR of 8 W/kg, averaged over any 1 gram of tissue (defined…

Text truncated - open the document above for the full version.

Report No.: RFBBQZ-WTW-P22060184-4 Page No. 1 / 45 Report Format Version:6.1.1 FCC Test Report (Co-Located) Report No.: RFBBQZ-WTW-P22060184-4 FCC ID: PY322300569 Test Model: WAX214v2 Received Date: 2022/6/8 Test Date: 2022/9/21 Issued Date: 2022/10/3 Applicant and Manufacturer: NETGEAR, INC. Address: 350 East Plumeria Drive San Jose, CA 95134 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: RFBBQZ-WTW-P22060184-4 Page No. 2 / 45 Report Format Version:6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes .................................................................................................................. 11 3.2.1 Test Mode Applicability and Tested Channel Detail ........................................................................... 14 3.3 Description of Support Units ............................................................................................................. 15 3.3.1 Configuration of System under Test .................................................................................................. 15 3.4 General Description of Applied Standards ........................................................................................ 16 4 Test Types and Results ...................................................................................................................... 17 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 17 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 17 4.1.2 Test Instruments ................................................................................................................................ 18 4.1.3 Test Procedures ................................................................................................................................. 20 4.1.4 Deviation from Test Standard ............................................................................................................ 20 4.1.5 Test Setup .......................................................................................................................................... 21 4.1.6 EUT Operating Conditions ................................................................................................................. 22 4.1.7 Test Results ....................................................................................................................................... 23 4.2 Conducted Out of Band Emission Measurement .............................................................................. 41 4.2.1 Limits of Conducted Out of Band Emission Measurement ............................................................... 41 4.2.2 Test Setup .......................................................................................................................................... 41 4.2.3 Test Instruments ................................................................................................…

Text truncated - open the document above for the full version.

Report No.: RFBBQZ-WTW-P22060184 Page No. 1 / 77 Report Format Version: 7.1.0 TEST REPORT CERTIFICATE OF CONFORMITY Standard: 47 CFR FCC Part 15, Subpart C (Section 15.247) Report No.: RFBBQZ-WTW-P22060184 FCC ID: PY322300569 Model No.: WAX214v2 Received Date: 2022/6/8 Test Date: 2022/8/26 ~ 2022/9/22 Issued Date: 2022/10/3 Applicant and Manufacturer: NETGEAR, INC. Address: 350 East Plumeria Drive San Jose CA 95134 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kewi Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 Approved by: , Date:2022/10/3 Jeremy Lin / Project Engineer This test report consists of 77 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. Prepared by : Celine Chou / Senior Specialist This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our- business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: RFBBQZ-WTW-P22060184 Page No. 2 / 77 Report Format Version: 7.1.0 Table of Contents Release Control Record ....................................................................................................................................................... 4 1 Certificate ............................................................................................................................................…

Text truncated - open the document above for the full version.