PY3MA401RDWireless PC Card

NETGEAR, Inc. 4401 Great America Parkway Santa Clara, CA 95054 USA Installation Guide for the Model MA401 802.11b Wireless PC Card Technical Support Please refer to the support information card that shipped with your product. By registering your product at www.NETGEAR.com/register , we can provide you with faster expert technical support and timely notices of product and software upgrades. NETGEAR, INC. Support Information Phone: 1-888-NETGEAR (For US & Canada only) For other countries see your Support information card. E-mail: [email protected] Web site: www.NETGEAR.com Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. ©2002 NETGEAR, Inc. NETGEAR, the Netgear logo, The Gear Guy and Everybody's Connecting are trademarks or registered trademarks of Netgear, Inc. in the United States and/or other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice. All rights reserved . November 2002 i Contents Chapter 1 - Introduction About the MA401 802.11b Wireless PC Card ..........................................1 Key Features and Related NETGEAR Products ......................................1 What’s in the Box? ...................................................................................2 Chapter 2 - Installing the MA401 802.11b Wireless PC Card What You Will Need Before You Begin ....................................................4 Verify System Requirements .............................................................5 Observe Location and Range Guidelines ..........................................5 Two Basic Operating Modes ....................................................................5 MA401 Default Wireless Configuration Settings ......................................6 Using the MA401 to Connect to a Wireless Access Point Network in Infrastructure Mode ..................................................................................7 Setup Instructions ....................................................................................8 For Windows XP Users Installing a MA401 .......................................8 For Windows 98/Me Users Installing a MA401 ................................ 11 For Windows 2000 Users Installing a MA401 ..................................14 Using the MA401 to Connect in Ad-Hoc Mode ......................................17 MA401 Wireless Connection Indicators .................................................18 Interpreting the LED on the MA401 .................................................18 Interpreting System Tray Icon Colors ..............................................19 Troubleshooting Tips ..............................................................................20 Chapter 3 - Protecting Your Wireless Connection Enabling Basic Wireless Security Features ...........................................21 Identifying the Wireless Network Name (SSID) and WEP Security Settings ............................................................................................22 Setting the Wireless Network Name (SSID) ....................................23 Configuring WEP Encryption Security .............................................23 1 Chapter 1 Introduction This chapter introduces the features, package contents, and appearance of the NETGEAR ® MA401 802.11b Wireless PC Card. About the MA401 802.11b Wireless PC Card The MA401 802.11b Wireless PC Card gives you ultimate mobility in your office or while you are traveling. It frees you from traditional Ethernet wiring and helps you create a wireless network for sharing your broadband cable or DSL Internet access among multiple PCs in and around your home. It is designed for notebook computers running Microsoft ® Windows ® . It is both 16-bit PCMCIA and 32-bit CardBus compatible and works in any available PCMCIA or CardBus slot. Its auto-sensing capability allows packet transfer at 11 Mbps for maximum throughput, or dynamic range shifting to the lower speeds due to distance or operating limitations in an environment with a lot of electromagnetic interference. It provides reliable, standards-based 802.11b LAN connectivity that is protected with industry-standard security. It works with Windows 95B, 98, Me, NT4, 2000, and XP operating systems. Key Features and Related NETGEAR Products The MA401 PC Card provides the following features: •Reliable IEEE 802.11b standard-based wireless technology. •Supports roaming between access points when configured in Infrastructure mode. 2 •11 Mbps high rate speed. Wireless nodes negotiate to operate in the optimal data transfer rate. In a noisy environment or when the distance between the wireless nodes is far, the wireless nodes automatically fall back to operate at the lower transfer rate of two or one Megabit per second. •Highest level of data encryption using128-bit Shared Key WEP data encryption method. Lower level of data encryption or no data encryption is available to simplify your network setup or to improve data transfer rate. The following Netgear products can be configured to communicate with the MA401 PC Card. •WAB102 Dual Band Access Point •WAB501 Dual Band PC Card •MA101 802.11b Wireless USB Adapter •ME102 802.11b Wireless Access Point •MA311 802.11b Wireless PCI Adapter •MR314 802.11b Wireless Cable/DSL Router •MA701 802.11b Wireless Compact Flash Card What’s in the Box? The product package should contain the following items: •MA401 802.11b Wireless PC Card •Installation Guide for the Model MA401 802.11b Wireless PC Card •Model MA401 R…

Text truncated - open the document above for the full version.

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 December 13, 2002 RE: Netgear, Inc. FCC ID: PY3MA401RD I have an immediate comment on this Application before I can begin. This transmitter is a PCMCIA card with integral antenna for unrestricted use across a wide variety of host devices. The rated RF power output as quoted on Form 731 is 63 milliwatts and, when combined with the maximum expected antenna gain gives maximum EIRP of nearly 100mW. Please review the TCB Exclusion List of July 17, 2002 attached separately to this email. You will see that there are two low threshold values for RF Exposure, above which SAR testing is required: 120mW/f(GHz) for devices which can maintain 2.5cm from the body, and 60mW/f(GHz) for devices which can come in contact with the body. PCMCIA cards are considered, under current FCC interpretation, a member of the second more severe group. It is no longer possible to approve PCMCIA cards using the RF category “Mobile” classification; they must have a SAR evaluation. Please submit a SAR report at your first opportunity. No further action on this Application will proceed until this is submitted. We will help you in every way possible as you seek a solution to this problem. If you have any further questions, please do not hesitate to ask. Regards, William H. Graff President and Examining Engineer mailto: [email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 January 21, 2003 RE: Netgear FCC ID: PY3MA401RD Thank you very much for the SAR report. We have, however, a couple additional comments. 1.) The supplied Manual makes reference to 20cm separation distance between the device and all persons. This is now incorrect because of the SAR testing. Please correct manual. 2.) A Modular approval is additionally requested for this device. Please provide separate installation instructions showing how OEM integrators should incorporate this device into their products. Please carefully consider how OEM integration should affect RF Exposure issues. 3.) Please describe in greater detail how this device was tested to insure compliance with the radiated “band edge” restrictions of 15.205, especially with the band edge below 2390 and above 2483.5MHz. William H. Graff President and Examining Engineer mailto: [email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

    




 

FCC ID Label Location 63 mm 39.5 mm






























Page 1 ANNEX PHOTOGRAPHS OF EUT Page 2 Page 3 Page 4 Page 5

FCC ID: PD5LMWP200RB Report No.: SA920109R03A1Issued: Jan. 15, 2003 SAR TEST REPORT REPORT NO.: SA920109R03A MODEL NO.: LM-WP200RB RECEIVED: Jan. 09, 2003 TESTED: Jan. 10, 2003 APPLICANT: Delta Networks, Inc. ADDRESS: 252, Shang Ying Road, KueiShan 333, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: 47 14th Lin, Chiapau Tsun, Linko, Taipei, Taiwan, R.O.C. This test report consists of 15 pages in total except Appendix. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, NVLAP or any government agencies. The test results in the report only apply to the tested sample. FCC ID: PD5LMWP200RB Report No.: SA920109R03A2Issued: Jan. 15, 2003 Table of Contents 1.CERTIFICATION ........................................................................................... 3 2.GENERAL INFORMATION ........................................................................... 4 2.1GENERAL DESCRIPTION OF EUT.............................................................. 4 2.2GENERAL DESCRIPTION OF APPLIED STANDARDS ............................... 4 2.3GENERAL INOFRMATION OF THE TEST SYSTEM.................................... 5 3.DESCRIPTION OF TEST MODES AND CONFIGURATIONS ...................... 7 4.DESCRIPTION OF SUPPORT UNITS .......................................................... 8 5.TEST RESULTS............................................................................................ 9 5.1TEST PROCEDURES................................................................................... 9 5.2MEASURED SAR RESULT........................................................................... 9 5.3SAR LIMITS ................................................................................................ 10 5.4EUT CONDUCTED POWER VARIATION ................................................... 10 5.5TISSUE ........................................................................................................11 5.6TEST EQUIPMENT FOR TISSUE PROPERTY...........................................11 6.SYSTEM VALIDATION................................................................................ 12 7.MEASUREMENT UNCERTAINTIES ........................................................... 13 8.INFORMATION ON THE TESTING LABORATORIES ................................ 15 APPENDIX A: TEST CONFIGURATIONS AND TEST DATA APPENDIX B: ADT SAR MEASUREMENT SYSTEM APPENDIX C: PHOTOGRAPHS OF SYSTEM VALIDATION APPENDIX D: SYSTEM CERTIFICATE & CALIBRATION FCC ID: PD5LMWP200RB Report No.: SA920109R03A3Issued: Jan. 15, 2003 1. CERTIFICATION PRODUCT : 11Mbps Wireless LAN PCMCIA Card MODEL NO. : LM-WP200RB BRAND : DNI APPLICANT : Delta Networks, Inc. STANDARDS : 47 CFR Part 2 (Section 2.1093), FCC OET Bulletin 65, Supplement C (01-01), RSS-102 We, Advance Data Technology Corporation, hereby certify that one sample of the designation has been tested in our facility on 10 th Jan. 2003. The test record, data evaluation and Equipment Under Test (EUT) configurations represented herein are true and accurate accounts for the measurements of the sample's EMC characteristics under the conditions herein specified. FCC ID: PD5LMWP200RB Report No.: SA920109R03A4Issued: Jan. 15, 2003 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT PRODUCT 11Mbps Wireless LAN PCMCIA Card MODEL NO. LM-WP200RB POWER SUPPLY 3.3VDC powered by host MODULATION TYPE BPSK, QPSK, CCK RADIO TECHNOLOGY DSSS TRANSFER RATE 1/2/5.5/11Mbps FREQUENCY RANGE 2412MHz ~ 2462MHz NUMBER OF CHANNEL 11 CONDUCTED OUTPUT POWER 62.6 mW ANTENNA TYPE Printed Inverted-F Antenna PEAK SAR 1.11 W/kg DATA CABLE NA I/O PORTS PCMCIA ASSOCIATED DEVICES NA 2.2 GENERAL DESCRIPTION OF APPLIED STANDARDS According to the specifications of the manufacturer, this product must comply with the requirements of the following standards: FCC 47 CFR Part 2 (2.1093) FCC OET Bulletin 65, Supplement C (01- 01) RSS-102 All tests have been performed and recorded as per the above standards. FCC ID: PD5LMWP200RB Report No.: SA920109R03A5Issued: Jan. 15, 2003 2.3 GENERAL INOFRMATION OF THE TEST SYSTEM ET3DV6 ISOTROPIC E-FIELD PROBE Construction Symmetrical design with triangular core. Built-in optical fiber for surface detection system. Built-in shielding against static charges. PEEK enclosure material (resistant to organic solvents, e.g., glycolether). Calibration Basic Broad Band Calibration in air: 10-2500 MHz Conversion Factors (CF) for HSL 900 and HSL 1800 CF-Calibration for other liquids and frequencies upon request Frequency 10 MHz to 3 GHz; Linearity: ± 0.2 dB (30 MHz to 3 GHz) Directivity ± 0.2 dB in HSL (rotation around probe axis) ± 0.4 dB in HSL (rotation normal to probe axis) Dynamic Range 5 μW/g to > 100 mW/g; Linearity: ± 0.2 dB Optical Surface Detection ± 0.2 mm repeatability in air and clear liquids over diffuse reflecting surfaces Dimensions Overall length: 337 mm (Tip Length: 10 mm) Tip diameter: 7.0 mm (Body diameter: 10 mm) Distance from probe tip to dipole centers: 2.7 mm Application General dosimetric measurements up to 3 GHz Compliance tests of mobile phones Fast automatic scanning in arbitrary phantoms (ET3DV6) FCC ID: PD5LMWP200RB Report No.: SA920109R03A6Issued: Jan. 15, 2003 TWIN SAM V4.0 Construction The shell corresponds to the specifications of the Specific Anthropomorphic Mannequin (SAM) phantom defined in IEEE 1528-200X, CENELEC 50361 and IEC 62209. It enables the dosimetric evaluation of left and right hand phone usage as well as body mounted usage at the flat phantom region. A cover prevents evaporation of the liquid. Reference markings on the phantom allow the complete setup of all predefined phantom positions and measurement grids by manually teaching three points with the robot. Shell Thickness 2 ± 0.2 mm Filling Volume Approx. 25 liters DimensionsHeight: 810 mm; Length: 1000…

Text truncated - open the document above for the full version.

      













 








































  




































              



      
     
 
   !       "  #$ % && '%() (  *(+ # * (* ,  - *+  ./








 





 



  
 










  


   




   





  


 


  


  










 

 



 































































































! " 
#  



$
%
#
&









      













 








































  

























 


'
(
) 
  *
((
   


#+*
(
, 
 
 

#+*
(-
,  
   .
('
! 
/  .


     0
(

 0

1 
 0
'

/  
-
2 
.%
% 
3
-(
1  
   3
-


4
 3
--
2


2 
.%
% 

3
'
2
1 
! 
(5
'(
1  
   (5
'


4
 (5
'-
2


2
1 
! 

(5
*
$6
,  
&  
  
((
*(
1  
   ((
*


4
 ((
*-
2




$6
,  
&  
  

((
.
$
#
(
.(
1  
   (
.


4
 (
.-
#
(-
.'
$
  


('
.'(
2 
7
/ 
/




(
)89('
.'
2 
7
/ 
 
()89(0
0
! 
  
: 
-
0(
1  
   -
0


4
 -









      













 








































  























0-
2


! 
  
: 

-

#


 

;6&&
(*'0<&= '
3
! 
 
&  
#

;6&&
(*50*
3(
1  
   *
3


4
 *
3-
! 
 
&  
#

.









      













 








































  























+ %0  





  






!"#



$  
$
2 
.%
% 

(*'0<=<=
&  
2…

Text truncated - open the document above for the full version.