PY3WG102ProSafe 802.11g Wireless Access Point

October 2004 October 2004 NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA Phone 1-888-NETGEAR Reference Manual for the NETGEAR WG102 ProSafe 802.11g Wireless Access Point 2 October 2004 Technical Support Please register to obtain technical support. Please retain your proof of purchase and warranty information. To register your product, get product support or obtain product information and product documentation, go to http://www.NETGEAR.com . If you do not have access to the World Wide Web, you may register your product by filling out the registration card and mailing it to NETGEAR customer service. You will find technical support information at: http://www.NETGEAR.com/ through the customer service area. If you want to contact technical support by telephone, see the support information card for the correct telephone number for your country. © 2004 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR is a registered trademark of NETGEAR, INC. Windows is a registered trademark of Microsoft Corporation. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice. All rights reserved. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. Modifications made to the product, unless expressly approved by Netgear, could void the user’s authority to operate the equipment. NETGEAR does not assume any liability that may occur due to such condition. October 2004 3 FCC Statement DECLARATION OF CONFORMITY We N e t g e a r, 4500 Great America Parkway Santa Clara, CA 95054, USA Tel: +1 408 907 8000 declare under our sole responsibility that the product(s) WG102 (Model Designation) 802.11g ProSafe Wireless Access Point (Product Name) complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio October 2004 4 frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: •Reorient or locate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. Placement and Range Guidelines Indoors, computers can connect over 802.11 wireless networks at a maximum range of several hundred feet for 802.11b/g devices. However, the operating distance or range of your wireless connection can vary significantly, based on the physical placement of the wireless access point. For best results, identify a location for your wireless access point according to these guidelines: •Away from potential sources of interference, such as PCs, large metal surfaces, microwaves, and 2.4 GHz cordless phones. •In an elevated location such as a high shelf that is near the center of the wireless coverage area for all mobile devices. Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the wireless access point. RF Exposure Warning for North America, and Australia Warning! To meet FCC and other national safety guidelines for RF exposure, the antennas for this device (see below) must be installed to ensure a minimum separation distance of 20cm (7.9 in.) from persons. Further, the antennas shall not be colocated with other antenna or radio transmitter. Antenna Statement for North America and Australia In addition to its own 2 antennas, the WG102 device has been approved for use with the following detachable antennas and antenna cables: Approved Antennas Antenna Gain and type Approved Antenna Cable Antenna Cable Length Maximum Transmitted Power NETGEAR ANT24D18 18 dBi, directional outdoor/indoor NETGEAR ACC-10314-01 thru 05 1.5 m to 30 m 18 dBm + 18 dBi ant. NETGEAR ANT2409 9 dBi, omnidirectional outdoor/indoor NETGEAR ACC-10314-01 thru 05 1.5 m to 30 m 18 dBm + 9 dBi ant. October 2004 5 * WG102 maximum radiated power in North America and Australia: 19 dBm – cable loss + antenna gain Please go to www.netgear.com/go/WG102_fcc for an updated list of wireless accessories approved to be used with the WG102 in North America and Australia. Industry Canada Compliance Statement This Class B Digital apparatus meets all the requirements of the Canadian Interference Causing Equipment Regulations ICES 003. Cet appareil numerique de classe B respecte les exigences du reglement du Canada sur le materiel brouilleur NMB-003. The device is certified to the requirements of RSS-210 for 2.4 GHz spread spectrum dev…

Text truncated - open the document above for the full version.

SerCommCorporation 8F,No.3-I,YuanQuSt.,Nankang,Taipei115,Taiwan,R.O.C. FederalCommunicationsCommission FCCID:PY3WG1O2! DearSir: Thisis torequestconfidentialityoninformationsubmittedforaboveapplication.We wouldliketo requestconfidentialityonsomeexhibitswesubmittedforaboveoriginal applicationforthereasonoftradesecret.If thoseexhibitsareavailableforpublic inspection,anypersonwhooncegetstheinformationcontainedinthoseexhibitswill beabletodesignandtomakethesameproductsveryeasily.Thisis a veryserious problemandhugelossforus,becausewedidinvestsomuchonit. PleasebenotmadetheExhibitTypeslistedbelowroutinelyavailableforpublic inspection: PartList Schematics BlockDiagram By:L-- kBy:KevinTseng (Signature) 7 Title: (Printed) Applicant:SerCommCorporation Address :8F,No.3-I,YuanQuSt.,Nankang,Taipei115,Taiwan,RO.C. Tel:+886-2-2655-3988Fax:+886-2-2655-3765 Date : Oct13,2004

SerCommCorporation 8F,No.3-I,YuanQuSt.,Nankang,Taipei115,Taiwan,R.O.C. FederalCommunicationsCommission DearSir: We,theundersigned,herebyauthorizeETSDr.GenzTaiwanPSCo.,Ltd.toactonour behalfinallmattersrelatingtoapplicationfor"(Model:WG102, FCCill:PY3WG102)"authorization,includingthesigningofalldocuments relatingtothesematters.AnyandallactscarriedoutbyETSDr.GenzTaiwanPS Co.,Ltd.onourbehalfshallhavethesameeffectasactsofourown. ~ Theapplicantcertifiesthatin thecaseofanindividualapplicant( e.g.,corporation), nopartyto theapplicantis subjecttoa denialoffederalbenefits,thatincludesFCC benefits,pursuanttosection5301oftheAnti-drugabuseActof1988,21V.S.C.862. Fora definitionofa "party"forthesepurposesSee47C.F.R.1.2002(b). By:~~~ t/. ~ By: KevinTseng (Printed)(Signature) Title Applicant:SerCommCorporation Address:8F,No.3-I,YuanQuSt.,Nankang,Taipei115,Taiwan,R.O.C. Tel:+886-2-2655-3988 Fax:+886-2-2655-3765 Date : Oct13,2004

Applicant: Netgear Incorporated Correspondence Reference Number: 32658 731 Confirmation Number: TC930282 To Whom It May Concern C/o Richard Tseng, [email protected] This letter is a response to your inquiry regarding Netgear’s product, FCC ID PY3WG102. By default, Netgear’s WG102 product, which indented to be sold in United States of America, is limited by Hardware and Software settings to operate only on channels 1-11. End user does not have a capability to change the region on its own. The only option in a user menu is North America/US settings. If you have any additional questions or concerns, please do not hesitate to contact Netgear. Thank you, Mark Gandler November 14, 2006 Sr. Compliance Engineer Netgear

________________________________________________________________________________ _______________ Registration number: W6M20409-5462-T-47 ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH External Photo Type of Antenna (A) ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany Type of Antenna (B) ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany Type of Antenna (C) ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany Type of Antenna (D) ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20408-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration…

Text truncated - open the document above for the full version.

65 mm 40 mm

MPE Prediction FCC Rule: 15.247(b)(5) Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines. See §1.1307(b)(1) of this Chapter. LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm2) Average time (minutes) (A)Limits For Occupational / Control Exposures 30-300 61.4 0.613 1.0 6 300-1500 ... ... F/300 6 1500-100,000 ... ... 5 6 (B)Limits For General Population / Uncontrolled Exposure 30-300 27.5 0.073 0.2 30 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz Prediction of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 PG S = -------------- 4πR² where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Maximum peak output power at antenna input terminal: 15.75 (dBm) Maximum peak output power at antenna input terminal: 38 (mW) Antenna gain(maximal): 5 (dBi) Prediction distance: 20 (cm) Prediction frequency: 2462 (MHz) MPE limit for uncontrolled exposure at prediction frequency: 1.0 (mW/cm²) Power density at prediction frequency: 0.037587 (mW/cm²) The manual instruct the user to install and operate the device in a minimum distance of 20 cm between antenna and the users body.

MPE Prediction FCC Rule: 15.247(b)(5) Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines. See §1.1307(b)(1) of this Chapter. LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm2) Average time (minutes) (A)Limits For Occupational / Control Exposures 30-300 61.4 0.613 1.0 6 300-1500 ... ... F/300 6 1500-100,000 ... ... 5 6 (B)Limits For General Population / Uncontrolled Exposure 30-300 27.5 0.073 0.2 30 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz Prediction of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 PG S = -------------- 4πR² where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Maximum peak output power at antenna input terminal: 16.23(dBm) Maximum peak output power at antenna input terminal: 42 (mW) Antenna gain(maximal): 5 (dBi) Prediction distance: 20 (cm) Prediction frequency: 2462 (MHz) MPE limit for uncontrolled exposure at prediction frequency: 1.0 (mW/cm²) Power density at prediction frequency: 0.041976 (mW/cm²) The manual instruct the user to install and operate the device in a minimum distance of 20 cm between antenna and the users body.

ELECTRONIC TECHNOLOGY SYSTEMS DR. GENZ GMBH FCC TEST - REPORT FCC Part 15 C for IEEE 802.11 b device FCC ID:PY3WG102 Test report no.: W6M20409-5462-C-1 ELECTRONIC TECHNOLOGY SYSTEMS STORKOWER STRASSE 38C, D-15526 REICHENWALDE B. BERLIN DR. GENZ GMBH PHONE +49-33631-888 00 FAX +49-33631-888 66 ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20409-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany 2 of 42 TABLE OF CONTENTS 1 GENERAL INFORMATION...................................................................................................3 1.1 NOTES...................................................................................................................................3 1.2 TESTING LABORATORY.........................................................................................................4 1.2.1 Location.......................................................................................................................4 1.2.2 Details of accreditation status.....................................................................................4 1.3 DETAILS OF APPROVAL HOLDER............................................................................................4 1.4 APPLICATION DETAILS..........................................................................................................5 1.5 GENERAL INFORMATION OF TEST ITEM.................................................................................5 1.6 TEST STANDARDS..................................................................................................................7 2 TECHNICAL TEST..................................................................................................................8 2.1 SUMMARY OF TEST RESULTS.................................................................................................8 2.2 TEST ENVIRONMENT..............................................................................................................8 2.3 TEST EQUIPMENT LIST..........................................................................................................9 2.4 GENERAL TEST PROCEDURE...............................................................................................16 3 TEST RESULTS (ENCLOSURE)..........................................................................................18 3.1 PEAK OUTPUT POWER (TRANSMITTER)...............................................................................19 3.2 EQUIVALENT ISOTROPIC RADIATED POWER.........................................................................21 3.2.1 Transmitter.................................................................................................................21 3.3 RF EXPOSURE COMPLIANCE REQUIREMENTS.....................................................................21 3.4 TRANSMITTER RADIATED EMISSIONS IN RESTRICTED BANDS.............................................22 3.5 SPURIOUS EMISSIONS (TX)..................................................................................................23 3.6 MINIMUM 6 DB BANDWIDTH..............................................................................................32 3.7 PEAK POWER SPECTRAL DENSITY.......................................................................................33 3.8 POWER LINE CONDUCTED EMISSION..................................................................................34 APPENDIX.......................................................................................................................................35 APPENDIX A....................................................................................................................................36 APPENDIX B....................................................................................................................................37 APPENDIX C....................................................................................................................................38 APPENDIX D....................................................................................................................................39 APPENDIX E....................................................................................................................................40 APPENDIX F....................................................................................................................................41 APPENDIX G....................................................................................................................................42 ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20409-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany 3 of 42 1 General Information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has Passed all the relevant tests conforms to a specification. Neither is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that is performance generally conforms to representative cases of communications equipment. The test results of this test report relate exclusively to the item tested as specified in 1.5. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the ELECTRONIC TECHNOLOGY SYSTEMS DR. GENZ GMBH. Specific Conditions: Usage of the hereunder tested device in combination with other integrated or external antennas requires at least additional output power measurements, spurious em…

Text truncated - open the document above for the full version.

ELECTRONIC TECHNOLOGY SYSTEMS DR. GENZ GMBH FCC TEST - REPORT FCC Part 15 C for IEEE 802.11 g device FCC ID:PY3WG102 Test report no.: W6M20409-5462-C-2 ELECTRONIC TECHNOLOGY SYSTEMS STORKOWER STRASSE 38C, D-15526 REICHENWALDE B. BERLIN DR. GENZ GMBH PHONE +49-33631-888 00 FAX +49-33631-888 66 ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20409-5462-C-2 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany 2 of 42 TABLE OF CONTENTS 1 GENERAL INFORMATION ................................................................................................... 3 1.1 N OTES ................................................................................................................................... 3 1.2 T ESTING LABORATORY ......................................................................................................... 4 1.2.1 Location .......................................................................................................................4 1.2.2 Details of accreditation status ..................................................................................... 4 1.3 D ETAILS OF APPROVAL HOLDER ............................................................................................ 4 1.4 A PPLICATION DETAILS .......................................................................................................... 5 1.5 G ENERAL INFORMATION OF T EST ITEM ................................................................................. 5 1.6 T EST STANDARDS .................................................................................................................. 7 2 TECHNICAL TEST ..................................................................................................................8 2.1 S UMMARY OF TEST RESULTS ................................................................................................. 8 2.2 T EST ENVIRONMENT.............................................................................................................. 8 2.3 T EST E QUIPMENT L IST .......................................................................................................... 9 2.4 G ENERAL T EST P ROCEDURE ............................................................................................... 16 3 TEST RESULTS (ENCLOSURE).......................................................................................... 18 3.1 P EAK O UTPUT P OWER ( TRANSMITTER ) ............................................................................... 19 3.2 E QUIVALENT ISOTROPIC RADIATED POWER ......................................................................... 21 3.2.1 Transmitter................................................................................................................. 21 3.3 RF E XPOSURE COMPLIANCE REQUIREMENTS..................................................................... 21 3.4 T RANSMITTER R ADIATED E MISSIONS IN R ESTRICTED B ANDS ............................................. 22 3.5 S PURIOUS E MISSIONS ( TX ) .................................................................................................. 23 3.6 M INIMUM 6 D B B ANDWIDTH .............................................................................................. 32 3.7 P EAK P OWER S PECTRAL D ENSITY ....................................................................................... 33 3.8 P OWER LINE CONDUCTED EMISSION.................................................................................. 34 APPENDIX ....................................................................................................................................... 35 A PPENDIX A.................................................................................................................................... 36 A PPENDIX B .................................................................................................................................... 37 A PPENDIX C .................................................................................................................................... 38 A PPENDIX D.................................................................................................................................... 39 A PPENDIX E .................................................................................................................................... 40 A PPENDIX F .................................................................................................................................... 41 A PPENDIX G.................................................................................................................................... 42 ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20409-5462-C-2 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany 3 of 42 1 General Information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has Passed all the relevant tests conforms to a specification. Neither is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that is performance generally conforms to representative cases of communications equipment. The test results of this test report relate exclusively to the item tested as specified in 1.5. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the ELECTRONIC TECHNOLOGY SYSTEMS DR. GENZ GMBH. Specific Conditions: Usage of the hereunder tested device in combination with other…

Text truncated - open the document above for the full version.

ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20409-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany Set Up Photo Type of Antenna (A) ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20409-5462-C-1 FCC ID: PY3WG102 ETS Dr. Genz GmbH, Germany ELECTRONIC TECHNOLOGY SYSTEMS DR.GENZ GMBH Registration number: W6M20409-5462-C-1 FCC ID: PY3WG102 ETS Dr. Gen…

Text truncated - open the document above for the full version.