PZWDWBT002Bluetooth Transmitter Module

Operation manual DWBT002 is installed in the handy scanner, so DWBT002 has no manual for user. The operation method of DWBT002 is described by the user manual of a handy scanner (that is, GT10 B-SB of DENSO WAVE). 1. Bar code data transmission to the host computer using communication equipment (1) Registration of handy scanner and selection of the handy scanner Transmits the registration signal from handy scanner and register the handy scanner at the communication equipment. Transmits the selection signal from communication equipment to the handy scanner and connect communication equipment with the handy scanner. (2) Bar code reading and data transfer Handy scanner reads the bar code and transmits the reading data to communication equipment. Communication equipment transmits the bar code data that carried out the receipt to a host computer. 2. Data communications with the personal computer equipped with radio. (1) Registration of Bar code handy scanner and selection of the Bar code handy scanner Transmits the registration signal from Bar code handy scanner and register the handy scanner at the personal computer. Transmits the selection signal from personal computer to the handy scanner and connect personal computer with the handy scanner. (2) Bar code reading and data transfer Handy scanner reads the bar code and transmits the reading data to personal computer. Personal computer calculates the received bar code data. Bar code label Bar code Label User’s Manual Requirement of FCC rule DWBT002 is installed in the handy scanner, so DWBT002 has no manual for user. FCC user’s manual requirements that are FCC rule Part 15.21 and 15.105 are described on user’s manual of the handy scanner (i.e. DENSO WAVE’s GT10B-SB). Fig 6.2. FCC rule requirement for user’s manual FCC and RSS-210 Regulations This device complies with Part 15of the FCC Rules and RSS-210 Rules Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Caution : Radio Frequency Exposure This device meets the FCC RF Exposure Guidelines in OET65. This transmitter and its antenna should not be placed next to other antennas or similar radiating structure . ICES-003 Regulation This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

DENSO WAVE INCORPORATED Bluetooth Board FCC ID: PZWDWBT002 Photos of Bluetooth Board Front Rear DENSO WAVE INCORPORATED Bluetooth Board FCC ID: PZWDWBT002 External Photo of Bluetooth Module IC (Component side) Internal Photo of Bluetooth Module IC (Component side) DENSO WAVE INCORPORATED Bluetooth Board FCC ID: PZWDWBT002 External Photo of Bluetooth Module IC (Solder side)

Label Layout on Bluetooth Board Unit : mm Fig. Label Layout Note: Compliance statement of marking will not be changed. But marking layout and size may be changed. * Label materials Surface material: Polypropylene Bonding material: Sticks on the product 18 20 Product Type Manufacturer

Appearance and FCC and IC Label Location of Bluetooth Board Appearance Fig. Photo of Bluetooth Board (Solder side) Location of FCC, IC Label

DENSO WAVE INCORPORATED Bluetooth Board FCC ID: PZWDWBT002 Photos of Bluetooth Board Front Rear DENSO WAVE INCORPORATED Bluetooth Board FCC ID: PZWDWBT002 External Photo of Bluetooth Module IC (Component side) Internal Photo of Bluetooth Module IC (Component side) DENSO WAVE INCORPORATED Bluetooth Board FCC ID: PZWDWBT002 External Photo of Bluetooth Module IC (Solder side)

Test report No. : 24GE0020-HO-1 Page : 2 of 37 Issued date : June 8, 2004 FCC ID : PZWDWBT002 UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(10.04.03) CONTENTS PAGE SECTION 1: Client information...................................................................................................... 3 SECTION 2: Equipment under test (E.U.T.) ................................................................................. 3 SECTION 3: Test specification, procedures & results .................................................................. 4 SECTION 4: Operation of E.U.T. during testing........................................................................... 6 SECTION 5: Conducted Emission, Section 15.207 ........................................................................ 8 SECTION 6: Carrier Frequency Separation, Section15.247(a)(1)............................................... 8 SECTION 7: 20dB Bandwidth, Section 15.247(a)(1) ..................................................................... 8 SECTION 8: Number of Hopping Frequency, Section 15.247(a)(1)(iii) ...................................... 9 SECTION 9: Dwell time, Section 15.247(a)(1)(iii) ......................................................................... 9 SECTION 10: Maximum Peak Output Power, Section 15.247(b)(1) ........................................... 9 SECTION 11: Band Edge Compliance, Section 15.247(c) ............................................................ 9 SECTION 12: Spurious Emission, Section 15.247(c)................................................................... 10 APPENDIX 1: Photographs of test setup...................................................................................... 11 Conducted Emission.............................................................................................................11 Spurious Emission (Radiated)............................................................................................. 12 Worst Case Position (X-axis:Horizontal / X-axis:Vertical) .............................................. 13 APPENDIX 2:Test instruments ...................................................................................................... 14 APPENDIX 3: Data of EMI test ..................................................................................................... 15 Conducted emission..............................................................................................................15 Carrier Frequency Separation ............................................................................................ 17 20dB Bandwidth ................................................................................................................... 19 Number of Hopping Frequency .......................................................................................... 21 Dwell time.............................................................................................................................. 23 Maximum Peak Output Power ........................................................................................... 26 Band Edge compliance......................................................................................................... 27 Spurious Emission(Radiated).............................................................................................. 28 Spurious Emission(Conducted)........................................................................................... 34 99% Occupied Bandwidth................................................................................................... 37 Test report No. : 24GE0020-HO-1 Page : 3 of 37 Issued date : June 8, 2004 FCC ID : PZWDWBT002 UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(10.04.03) SECTION 1: Client information Company Name : DENSO WAVE INCORPORATED Brand name : DENSO Address : 1-1 Showa-cho, Kariya-shi, Aichi-ken, 448-8661 Japan Telephone Number : +81-566-25-9802 Facsimile Number : +81-566-25-4780 Contact Person : Takayoshi Arakawa SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : Bluetooth Board Model No. : DWBT002 Serial No. : No.1 (for the AC Main Conducted emission test) No.3 (for the Radiated emission test) No.4 & 10 (for the Antenna terminal conducted test) Country of Manufacture : Japan Rating : DC3.3V/0.12A Receipt Date of Sample : February 3, 2004 Condition of EUT : Production Prototype (Not for Sale: This sample is equivalent to mass-produced items.) 2.2 Product Description Model No: DWBT002 is the Bluetooth Board. It is the communication equipment according to the radio standard of Bluetooth. It builds in a bar code scanner and a communication unit. Equipment Type : Transceiver Frequency of operation : 2402-2480MHz Type of modulation : FSK(FHSS) Bandwidth & Channel spacing : 79MHz & 1MHz Antenna Type : AH122F245001 Antenna connector Type : N/A Antenna Gain : 1dBi Power Supply : DC3.3V Temperature of operation : 0 deg. C. to +40 deg. C. FCC 15.31 (e) This EUT provides stable voltage(DC3.3V) constantly to RF Module regardless of input voltage. Therefore, this EUT complies with the requirement. FCC Part 15.203 and 204 Antenna requirement Since the antenna used is a type of chip component and is permanently mounted by soldering on a printed circuit board in DWBT002, It is impossible for end users to replace it without assistance of professionals. Therefore, this EUT complies with the requirement. Test report No. : 24GE0020-HO-1 Page : 4 of 37 Issued date : June 8, 2004 FCC ID : PZWDWBT002 UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(10.04.03) SECTION 3: Test specification, procedures & results 3.1 Te…

Text truncated - open the document above for the full version.

Test report No. : 24GE0020-HO-1 Page : 11 of 37 Issued date : June 8, 2004 FCC ID : PZWDWBT002 UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(10.04.03) APPENDIX 1: Photographs of test setup Conducted Emission Front Rear Test report No. : 24GE0020-HO-1 Page : 12 of 38 Issued date : June 8, 2004 FCC ID : PZWDWBT002 Revised date : June 14, 2004 UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(10.04.03) Spurious Emission (Radiated) Front Rear Test report No. : 24GE0020-HO-1 Page : 13 of 38 Issued date : June 8, 2004 FCC ID : PZWDWBT002 Revised date : June 14, 2004 UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(10.04.03) Worst Case Position (X-axis:Horizontal / X-axis:Vertical) X-axis Y-axis Z-axis