PZWDWBT013Bluetooth Adapter

Jun 10, 2014 1 DWBT013 Installation Manual Contents1. Supply Voltage2. Dimensions and Connector specification 3. Notice Jun 10, 2014 2 1. Supply Voltage DC 3.0-3.6V Supply Voltage Range (Note) DC 3.3V Supply Voltage Specifications Item Note: These values are specifie d at the conn ector terminal. Jun 10, 2014 3 2. Dimensions and Connector specification (15mm) (31mm) (3mm) Specification: 0.5mm PITCH FPC CONNECTORCircuits: 18 Connector Label (Electronic components were omitted) Jun 10, 2014 4 3. Notice This device complies with part 15 of the FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. Le présent appareil est conforme aux la partie 15 des règles de la FCC et CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autor isée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. When the DWBT013 is installed in Class A equipment When the DWBT013 is installed in Class B equipment Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help. Jun 10, 2014 Radiation Exposure Statement: The product comply with the FCC and Canada portable RF exposur e limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The fu rther RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set th e device to lower output power if such function is available. Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établiespour un environnement non contrôlé.Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé surla puissance de sortie la plus faible si une telle fonction est disponible. Déclaration d'exposition aux radiations: Changes or modifications not expressly approved by the party re sponsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. FCC CAUTION: Jun 10, 2014 IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC and Canada authorization is no longer considered valid and the FCC ID and IC-ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Canada authorization. NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'IDIC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produitfinal (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. This device is intended only for OEM integrators under the following conditions: 1)The transmitter module may not be co-located with any other transmitter or antenna. 2)Module approval valid only when the module is installed in the tested host or compatible series of host As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.2) L'approbation du module est valable uniquement lo…

Text truncated - open the document above for the full version.

FCC ID: PZWDWBT013 Report No.: RF140407C13 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch June 4, 2014 Dear Application Examiner, DENSO WAVE INCORPORATED, Bluetooth Adapter, FCC ID: PZWDWBT013 would like to have your authorization as a modular approval specific to the portable product (Brand: Denso, Model: SE1-QB) The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip STM32F205REY6 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is STM32F205REY6. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested inside a specific platform. Please see section Photographs of Test Configuration in the test report, the EUT is for limited modular approval for this specific platform. Please refer to as below for more detail of specific platform. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: PZWDWBT013 Report No.: RF140407C13 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Robert Huang Senior Engineer Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Page 1 CONSTRUCTION PHOTOS OF EUT

1/1 Product label and label placement drawing. for Module Product label Label placement drawing End product rear view Label ＊ AC0086 ＊ ＊＊

Page 2 Page 3 Page 4 Bluetooth Module Page 5 Page 6

Report No.: SA140401C04A 1 of 6 Report Format Version 5.0.0 Reference No.: 140407C13 RF EXPOSURE REPORT REPORT NO.: SA140401C04A MODEL NO.: DWBT013 FCC ID: PZWDWBT013 RECEIVED: Apr. 07, 2014 TESTED: Apr. 09 ~ Apr. 12, 2014 ISSUED: Apr. 18, 2014 APPLICANT: DENSO WAVE INCORPORATED ADDRESS: 1 Yoshiike Kusagi Agui-cho, Chita-gun Aichi 470-2297, Japan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SA140401C04A 2 of 6 Report Format Version 5.0.0 Reference No.: 140407C13 Table of Contents RELEASE CONTROL RECORD .............................................................................................. 3 1. CERTIFICATION ........................................................................................................... 4 2. EVALUATION RESULT ................................................................................................. 5 3. SAR TEST EXCLUSION THRESHOLDS ..................................................................... 6 4. CONCLUSION .............................................................................................................. 6 Report No.: SA140401C04A 3 of 6 Report Format Version 5.0.0 Reference No.: 140407C13 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA140401C04A Original release. Apr. 18, 2014 Report No.: SA140401C04A 4 of 6 Report Format Version 5.0.0 Reference No.: 140407C13 1. CERTIFICATION PRODUCT: Bluetooth Adapter MODEL NO.: DWBT013 BRAND: DENSO APPLICANT: DENSO WAVE INCORPORATED TESTED: Apr. 09 ~ Apr. 12, 2014 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1093) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: DWBT013) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Apr. 18, 2014 Jemma Yang / Specialist APPROVED BY: , DATE :Apr. 18, 2014 Ken Liu / Senior Manager Report No.: SA140401C04A 5 of 6 Report Format Version 5.0.0 Reference No.: 140407C13 2. EVALUATION RESULT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,16 where  f(GHz) is the RF channel transmit frequency in GHz .  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Report No.: SA140401C04A 6 of 6 Report Format Version 5.0.0 Reference No.: 140407C13 3. SAR TEST EXCLUSION THRESHOLDS Maximum measured transmitter power: Frequency (GHz) Max. Power (mW) Min. test separation distance (mm) SAR test exclusion calculation value (NOTE 2) 1-g SAR test exclusion thresholds Result 2.402 ~ 2.480 1.521 5 0.471 3 Pass NOTE: 1. T…

Text truncated - open the document above for the full version.

Report No.: RF140401C04A 1 of 42 Report Format Version 5.0.0 Reference No.: 140407C13 FCC TEST REPORT (BLUETOOTH) REPORT NO.: RF140401C04A MODEL NO.: DWBT013 FCC ID: PZWDWBT013 RECEIVED: Apr. 07, 2014 TESTED: Apr. 09 ~ Apr. 12, 2014 ISSUED: Apr. 18, 2014 APPLICANT: DENSO WAVE INCORPORATED ADDRESS: 1 Yoshiike Kusagi Agui-cho, Chita-gun Aichi 470-2297, Japan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF140401C04A 2 of 42 Report Format Version 5.0.0 Reference No.: 140407C13 Table of Contents RELEASE CONTROL RECORD .............................................................................................................. 4 1. CERTIFICATION ........................................................................................................................... 5 2. SUMMARY OF TEST RESULTS .................................................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ................................................................................................ 6 3. GENERAL INFORMATION ........................................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................. 7 3.2 DESCRIPTION OF TEST MODES ............................................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................................... 9 3.3 DESCRIPTION OF SUPPORT UNITS ....................................................................................... 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ........................................................................ 11 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................................ 12 4. TEST TYPES AND RESULTS .................................................................................................... 13 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................... 13 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................. 13 4.1.2 TEST INSTRUMENTS ................................................................................................................ 14 4.1.3 TEST PROCEDURES ................................................................................................................ 15 4.1.4 DEVIATION FROM TEST STANDARD ...................................................................................... 15 4.1.5 TEST SETUP .............................................................................................................................. 16 4.1.6 EUT OPERATING CONDITIONS ............................................................................................... 16 4.1.7 TEST RESULTS ......................................................................................................................... 17 4.2 NUMBER OF HOPPING FREQUENCY USED .......................................................................... 24 4.2.1 LIMIT OF HOPPING FREQUENCY USED ................................................................................ 24 4.2.2 TEST SETUP .............................................................................................................................. 24 4.2.3 TEST INSTRUMENTS ................................................................................................................ 24 4.2.4 TEST PROCEDURES ................................................................................................................ 24 4.2.5 DEVIATION FROM TEST STANDARD ...................................................................................... 24 4.2.6 TEST RESULTS ......................................................................................................................... 24 4.3 DWELL TIME ON EACH CHANNEL .......................................................................................... 26 4.3.1 LIMIT OF DWELL TIME USED ................................................................................................... 26 4.3.2 TEST SETUP ...................................................................................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST