PZWDWWB003BHT-1300-CE Main Board

1 For OEM integration only – device cannot be sold to general public.Therefore we will ask OEM to include the following statements required by FCC on the product and in the Installation manual Notice. DWWB003 Installation Manual Contents1.Land Pattern(Recommended)2.Supply Voltage3.Pin configuration 4.Notice 2 1.Land Pattern(Recommended Unit:mm) 3 2. Supply Voltage Please supply a stabilized power supp ly voltage through the VBAT And VIO. Typ.[V] Min.[V] Max.[V] VBAT 3.6 3.0 4.2 VIO 1.8 1.65 1.92 4 3. Pin configuration 5 4. Notice Please describe the following warning on the final product which contains this module. Contains Transmitter Mobile FCC ID:PZWDWWB003 Contains FCC ID:PZWDWWB003 or 6 When installing it in a mobile equipment Please describe the following warning to the manual. When installing it in a portable equipment [ Model Name ] Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may n ot cause harmful interference, and (2) this device must accept any interference received, including inte rference that may cause undesired operat ion. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasona ble protection against harmful interference in a re sidential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance w ith the instructions, may cause harmful interference to radio co mmunications. However, there is no guarantee that interference w ill not occur in a particular installation. If this equipment does cause harmful inte rference to radio or television reception, which can be determined by turning the equipment off a nd on, the user is encouraged to try to correct the interferen ce by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outle t on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or m odifications not expressly approved by the party re sponsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontro lled environment and are safe for intended operation as described in this manual. The further RF exposure reductio n can be achieved if the product can be ke pt as far as possibl e from the user body or set the device to lower output power if such function is available. This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. 2) Module approval valid only when the module is installed in the tested host or compatible series of host As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requir ements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no long er considered valid and the FCC ID can not be used on the final product. In thes e circumstances, the OEM integrator will be responsible for re-evaluating the end product (inclu ding the transmitter) and obtaining a separate FCC authorization. End Product Labeling The product can be kept as far as possible from the user body or set the device to lowe r output power if such function is available. The final end product must be labeled in a visible area with the following: “Contains FCC ID: PZWDWWB003”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or re move this RF module in the user’s manual of the end product which in tegrates this module. The end user manual shall include all required regulato ry information/warning as show in this manual. Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including inte rference that may cause undesired operat ion. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appa reils radio exempts de licence. Son fonctio nnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudicia ble, et (2) ce dispositif doit accepter to ut brouillage reçu, y compris un brouillage susceptible de provoquer un fonc tionnement indésirable. Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit se t forth for an uncontrolled environment and are safe for intend ed operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possibl e from the user body or s et the device to lower output power if such function is available. Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'expositi on pour les appareils portables RF pour …

Text truncated - open the document above for the full version.

FCC ID: PZWDWWB003 Report No.: RF140407C17 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch June 4, 2014 Dear Application Examiner, DENSO WAVE INCORPORATED, BHT-1300-CE Main Board, FCC ID: PZWDWWB003 would like to have your authorization as a modular approval specific to the portable product (Brand: Denso, Model: BHT-1361QWB-CE, BHT-1361BWB-CE) The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip 50028 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is 50028. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested inside a specific platform. Please see section Photographs of Test Configuration in the test report, the EUT is for limited modular approval for this specific platform. Please refer to as below for more detail of specific platform. FCC ID: PZWDWWB003 Report No.: RF140407C17 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Robert Huang Senior Engineer Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Page 1 CONSTRUCTION PHOTOS OF EUT Specific End-product (Handy Terminal): BHT-1361QWB-CE Page 2 Specific End-product (Handy Terminal): BHT-1361BWB-CE

Module

Page 3 Specific End-product (Handy Terminal): BHT-1361QWB-CE Page 4 Page 5 Page 6 Page 7 WLAN & BT module Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Specific End-product (Handy Terminal): BHT-1361BWB-CE Page 15 Page 16 Page 17 Page 18 WLAN & BT module Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25

Report No.: SA140407C17 1 of 6 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA140407C17 MODEL NO.: DWWB003 FCC ID: PZWDWWB003 RECEIVED: Apr. 07, 2014 TESTED: Apr. 08 ~ Apr. 18, 2014 ISSUED: Apr. 22, 2014 APPLICANT: Denso Wave Incorporated ADDRESS: 1 Yoshiike Kusagi Agui-cho, Chita-gun Aichi 470-2297 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SA140407C17 2 of 6 Report Format Version 5.0.0 Table of Contents RELEASE CONTROL RECORD .............................................................................................. 3 1. CERTIFICATION ........................................................................................................... 4 2. EVALUATION RESULT ................................................................................................. 5 3. SAR TEST EXCLUSION THRESHOLDS ..................................................................... 6 4. CONCLUSION .............................................................................................................. 6 Report No.: SA140407C17 3 of 6 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA140407C17 Original release. Apr. 22, 2014 Report No.: SA140407C17 4 of 6 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT:BHT-1300-CE Main Board MODEL NO.:DWWB003 BRAND:DENSO APPLICANT:Denso Wave Incorporated TESTED:Apr. 08 ~ Apr. 18, 2014 TEST SAMPLE:ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1093) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: DWWB003) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Apr. 22, 2014 Suntee Liu / Specialist APPROVED BY: , DATE :Apr. 22, 2014 Ken Liu / Senior Manager Report No.: SA140407C17 5 of 6 Report Format Version 5.0.0 2. EVALUATION RESULT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz .  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [(Threshold at 50 mm in step 1) + (test separation distance - 50mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [(Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Report No.: SA140407C17 6 of 6 Report Format Version 5.0.0 3. SAR TEST EXCLUSION THRESHOLDS Maximum measured transmitter power: Frequency (GHz) Max. Power (mW) Min. test separation distance (mm) SAR test exclusion calculation value (NOTE 2) 1-g SAR test exclusion thresholds Result 2.402 ~ 2.480 1.968 5 0.610 3 Pass NOTE: 1. The antenna type is PIFA antenna with 1.31dBi gain. 2. Calculate SAR test exclusion thresholds from condition “1” formulas. 4. CONCLUSION Since Source-base time averag…

Text truncated - open the document above for the full version.

FCC SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 24 Report No. : SA140407C17 Issued Date : May 30, 2014 FCC SAR Test Report Report No. : SA140407C17 Applicant : Denso Wave Incorporated Address : 1 Yoshiike Kusagi Agui-cho, Chita-gun Aichi 470-2297 Product : BHT-1300-CE Main Board FCC ID : PZWDWWB003 Brand : DENSO Model No. : DWWB003 Standards : FCC 47 CFR Part 2 (2.1093) / IEEE C95.1:1992 / IEEE 1528:2003 IEEE 1528a-2005 / KDB 865664 D01 v01r03 KDB 248227 D01 v01r02 / KDB 447498 D01 v05r02 Sample Received Date : Apr. 07, 2014 Date of Testing : May 09, 2014 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch – Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Evonne Liu / Specialist Approved By : Roy Wu / Manager This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. FCC SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 24 Report No. : SA140407C17 Issued Date : May 30, 2014 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 6 3.2 SPEAG DASY System ................................................................................................................................................. 6 3.2.1 Robot.................................................................................................................................................................. 7 3.2.2 Probes ................................................................................................................................................................ 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................... 8 3.2.4 Phantoms ........................................................................................................................................................... 9 3.2.5 Device Holder ................................................................................................................................................... 10 3.2.6 System Validation Dipoles ................................................................................................................................ 10 3.2.7 Tissue Simulating Liquids ................................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 14 3.4 SAR Measurement Procedure ................................................................................................................................... 15 3.4.1 Area & Zoom Scan Procedure ......................................................................................................................... 15 3.4.2 Volume Scan Procedure................................................................................................................................... 15 3.4.3 Power Drift Monitoring ...................................................................................................................................... 16 3.4.4 Spatial Peak SAR Evaluation ........................................................................................................................... 16 3.4.5 SAR Averaged Methods ...........................................................…

Text truncated - open the document above for the full version.

Report No.: RF140407C17-1 1 of 54 Report Format Version 5.0.0 FCC TEST REPORT (BLUETOOTH) REPORT NO.: RF140407C17-1 MODEL NO.: DWWB003 FCC ID: PZWDWWB003 RECEIVED: Apr. 07, 2014 TESTED: Apr. 08 ~ Apr. 18, 2014 ISSUED: Apr. 22, 2014 APPLICANT: Denso Wave Incorporated ADDRESS: 1 Yoshiike Kusagi Agui-cho, Chita-gun Aichi 470-2297 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF140407C17-1 2 of 54 Report Format Version 5.0.0 Table of Contents RELEASE CONTROL RECORD .............................................................................................................. 4 1. CERTIFICATION ........................................................................................................................... 5 2. SUMMARY OF TEST RESULTS .................................................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ................................................................................................ 6 3. GENERAL INFORMATION ........................................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................. 7 3.2 DESCRIPTION OF TEST MODES ............................................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................................... 9 3.3 DESCRIPTION OF SUPPORT UNITS ....................................................................................... 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ........................................................................ 12 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................................ 14 4. TEST TYPES AND RESULTS .................................................................................................... 15 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................... 15 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................. 15 4.1.2 TEST INSTRUMENTS ................................................................................................................ 16 4.1.3 TEST PROCEDURES ................................................................................................................ 17 4.1.4 DEVIATION FROM TEST STANDARD ...................................................................................... 17 4.1.5 TEST SETUP .............................................................................................................................. 18 4.1.6 EUT OPERATING CONDITIONS ............................................................................................... 18 4.1.7 TEST RESULTS ......................................................................................................................... 19 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................................. 29 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT .......................................................... 29 4.2.2 TEST INSTRUMENTS ................................................................................................................ 29 4.2.3 TEST PROCEDURES ................................................................................................................ 30 4.2.4 DEVIATION FROM TEST STANDARD ...................................................................................... 30 4.2.5 TEST SETUP .............................................................................................................................. 31 4.2.6 EUT OPERATING CONDITIONS ............................................................................................... 31 4.2.7 TEST RESULTS ......................................................................................................................... 32 4.3 NUMBER OF HOPPING FREQUENCY USED .......................................................................... 36 4.3.1 LIMIT OF HOPPING FREQUENCY USED ................................................................................ 36 4.3.2 TEST SETUP .........................................................................…

Text truncated - open the document above for the full version.

Report No.: RF140407C17 1 of 55 Report Format Version 5.2.0 FCC TEST REPORT (WLAN) REPORT NO.: RF140407C17 MODEL NO.: DWWB003 FCC ID: PZWDWWB003 RECEIVED: Apr. 07, 2014 TESTED: Apr. 08 ~ Apr. 18, 2014 ISSUED: Apr. 22, 2014 APPLICANT: Denso Wave Incorporated ADDRESS: 1 Yoshiike Kusagi Agui-cho, Chita-gun Aichi 470-2297 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF140407C17 2 of 55 Report Format Version 5.2.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................ 4 1. CERTIFICATION ............................................................................................................ 5 2. SUMMARY OF TEST RESULTS .................................................................................... 6 2.1 MEASUREMENT UNCERTAINTY .................................................................................. 6 3. GENERAL INFORMATION ............................................................................................. 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................... 7 3.2 DESCRIPTION OF TEST MODES ................................................................................. 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................. 9 3.3 DUTY CYCLE OF TEST SIGNAL ......................…

Text truncated - open the document above for the full version.