Q3MBTG100Bluetooth Audio Gateway

1 Table of Contents Introduction................................................................................3 Installation..................................................................................6 Pairing Bluetooth headset with the Gateway...................................8 Making a call...............................................................................8 Answering a call........................................................................10 Pairing with Multiple Headsets.....................................................10 Specifications............................................................................11 Troubleshooting........................................................................12 First edition (April 2004) Corrections, changes and improvements to this manual might be made at any time and without notice. Such update will, however, might be incorporated into new edition of this manual. The manufacturer assumes no responsibility or reliability for any error or inaccuracy that may appear in this user guide. All rights reserved. Bluetooth is trademark of the Bluetooth SIG, Inc. The trademark are owned by Bluetooth SIG, Inc. USA 2 FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condition: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and use in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: z Reorient or relocate the receiving antenna. z Increase the separation between the equipment and receiver. z Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. z Consult the dealer or an experienced radio/TV technician for help. z You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 3 A. Introduction Thank you for your purchase of BTG-100, Bluetooth Phone Audio Gateway. Your BTG-100 enables convenient cordless communication with analogue landline phone and Bluetooth headset that are compliant with Bluetooth version 1.1 (or higher) and support the headset profile. Bluetooth technology make wireless link between any compatible mobile and stationary communication devices. The technology adopts a global available RF frequency range to establish RF link that offer secure, fast and reliable transmission of voice and data. This user guide is intended to help you set up the gateway and to quickly familiarize yourself with its operations. This document will guide you through the installation and provide you with instructions on how to use the gateway’s features. What is inside the box The following items should be in your giftbox that comes with the Bluetooth Phone Audio Gateway. If an item is missing, please contact your dealer. Quantity Description BTG-100 Bluetooth Phone Audio Gateway for house phone * 1 Linear AC Power Adapter with cord * 1 Phone cord * 1 User Manual * 1 Quick Start Guide * 1 It is recommended to use the power supply provided, otherwise there is risk of damaging the Bluetooth phone audio gateway. PICTURES of ITEMS in the BOX BTG-100 Audio Gateway Linear AC Power Adapter RJ-11 Phone cord 4 Product Overview 5 Top View Pairing Button LED 2/Power LED (Blue) - Blue on while in Talk Mode - Blue flashes as in Standby Mode pairing failed LED 1/Pairing LED (Red) Red flashes while Pairing Mode starts or during Phone Rings Antenna Rear View VR (Variable Resistor) for transmitter gain adjustment DC Jack RJ-11 Jack for Analog Landline RJ-11 Jack for Phone Line B. Installation Follow the procedures below to hook up your Gateway to your phone, cordless or otherwise. This would allow you to receive or make call with your Bluetooth headset through a regular phone line. This also frees you from being restrained by the length of your phone cord during conversation. 1. Un-hook the original phone line from the phone. 2. Hook up the Gateway by RJ11 port marked “PHONE” to your landline phone using the phone cord provided in the giftbox. 3. Hook up the original phone line to another phone jack marked “LINE” (RJ11 next to the power jack) on the Gateway 6 4. Verify if working range of your AC power adapter input voltage complies to local receptacle output voltage. 5. Plug the AC power adapter to the DC power Jack of Gateway and plug the leads of AC power adapter to a receptacle that provides corresponding power source. 6. The LED Indicator start to flashes blue after power on. 7 8 C. Pairing Bluetooth Headset with the Gateway 1. Make sure the Gateway is powered on and is in idle mode. That is, LED indicator should be blinking every two (2) seconds. 2. Set the Bluetooth headset in its “pairing mode”. Please refer to your headset manufacturer user documentation on pairing for the proper procedures. 3. The Passkey (Pin Code) of the Gateway has been pre-stored in factory as 0000. 4. Make sure your Bluetooth headset’s PIN code is the same as the Gateway has. 5. Press the “Pair” button on the Gateway and release, LED indicator start blinking red Within a few seconds, then LED Indicator shall flash both red and blu…

Text truncated - open the document above for the full version.

Agent Authorization Letter attn: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize MET Laboratories, Inc. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C.853(a). This agreement expires one year from the current date.

Chris Harvey From: [email protected] Sent: Thursday, August 05, 2004 3:14 AM To: Chris Harvey Cc: [email protected]; [email protected]; 'Marianne Bosley'; [email protected]; [email protected] Subject: Re: Additional Information needed G-TEK Bluewtooth Audio Gateway FCC ID: Q3MBTG100 Page 1 of 2 8/5/2004 Dear Chris, Thank you very much for your command on this project. We have modified those documents you mentioned. Please find enclosed "Revised FCC ID Label" and "Rev. User Manual" for this project. Should there be any problem or mistake, please let me know. Again, thank you for your consideration upon this matter! Best Regards, Elisa Chen --- Elisa Chen E&E Lab. of SGS Taiwan Ltd. E-Mail: [email protected] TEL: +886 2 2299 3279 ext. 1161 FAX: +886 2 2298 2698 No. 134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan Dear Elisa, I have reviewed the application referenced above for compliance with the FCC requirements and have the following comments and questions: 1. The FCC ID label exhibit shows the required statement to comply with FCC 15.19 (2-part statement), however the photograph shows a label without this statement. The Statement is also located in the Users¡¦ manual. If the intent is to place this statement only in the manual, then you must justify not having this on the product. Typically if a device is smaller than the palm of a hand this can be justified. 2. The test report documents Peak Power of +8dBm, however the Users Manual appears to state that this device has a maximum power of +18dBm. Please correct this discrepancy. Chris Harvey <[email protected]> 2004/08/01 12:37 AM To: [email protected] cc: 'Marianne Bosley' <[email protected]>, [email protected], [email protected], [email protected] Subject: Additional Information needed G-TEK Bluewtooth Audio Gateway FCC ID: Q3MBTG100 3. The Users Manual does not contain the required statement to comply with FCC 15.21. Please submit a revised manual to include this information. 4. Please note that this device connects to the Public Switched Telephone Network, and thus requires compliance with Pt. 68. There will be a condition placed on the Grant indicating that fact. 5. Since you have stated that this device is compliant with the Bluetooth Specification, I am going to submit the attached document with this application to indicate compliance with several FCC requirements not already covered in your application. Devices that are Bluetooth Compliant will comply with these FCC requirements, but there must be documentation in the exhibits to state specific compliance. Please submit this attachment with future FCC Bluetooth applications to be complete. Please contact me if you have any questions. Best regards, Chris Harvey Page 2 of 2 8/5/2004

REPORT NO: EF/2004/70004 ID: Q3MBTG100 DATE: Jul. 29, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA APPENDIX 2 EXTERNAL OF EUT REPORT NO: EF/2004/70004 ID: Q3MBTG100 DATE: Jul. 29, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA Power Adaptor Front View of EUT REPORT NO: EF/2004/70004 ID: Q3MBTG100 DATE: Jul. 29, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA Back View of EUT Top View of EUT

FCC ID LABEL FORMAT AND LOCATION Applicant: G-TEK Electronics Corporation FCC ID: Q3MBTG100 P68 ID: 1YDTE00BBTG-100XX FCC ID: Q3MBTG100 P68 ID: 1YDTE00BBTG-100XX This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID LABEL AREA

REPORT NO: EF/2004/70004 ID: Q3MBTG100 DATE: Jul. 29, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA APPENDIX 3 INTERNAL OF EUT REPORT NO: EF/2004/70004 ID: Q3MBTG100 DATE: Jul. 29, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA Open View of EUT Internal of EUT REPORT NO: EF/2004/70004 ID: Q3MBTG100 DATE: Jul. 29, 2004 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA Internal of EUT BT modular

REPORT NO: EF/2004/70004 ID: Q3MBTG100 DATE: Jul. 29, 2004 Page: 1 of 54 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF Product Name: Audio Gateway Brand Name: G-Tek Model Name: BTG-100, BTG-100XX Model Difference: Variant in colors FCC ID: Q3MBTG100 Report No.: EF/2004/70004 Issue Date: Jul. 29, 2004 FCC Rule Part: 15.247 Prepared for: G-TEK Electronics Corporation 16F, 106 Sec 1 ,Hsin Tai 5th Road, Hsi- chih, Taipei Taiwan Prepared by: SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei County, Taiwan. Note: This report shall not be reproduced except in full, without the written approval of SGS Taiwan Ltd. This document may be altered or revised by SGS Taiwan Ltd. personnel only, and shall be noted in the revision section of the document. REPORT NO: EF/2004/70004 ID: Q3MBTG100 DATE: Jul. 29, 2004 Page: 2 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA VERIFICATION OF COMPLIANCE Applicant: G-TEK Electronics Corporation 16F, 106 Sec 1 ,Hsin Tai 5th Road, Hsichih, Taipei Taiwan Equipment Under Test: Audio Gateway Brand Name: G-Tek FCC ID Number: Q3MBTG100 Model No.: BTG-100, BTG-100XX Model Difference: Variant in colors File Number: EF/2004/70004 Date of test: Jul. 15, 2004 ~ Jul. 28, 2004 Date of EUT Received: Jul. 14, 2004 We hereby certify that: The above equipment was tested by SGS Taiwan Ltd. The test data, data evaluation, test proce- dures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2001) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.247 The test results of this report relate only to the tested sample identified in this report. Test By: Date Jul. 29, 2004 Alex Hsieh Approved By Date Jul. 29, 2004 Vincent Su REPORT NO: EF/2004/70004 ID: Q3MBTG100 DATE: Jul. 29, 2004 Page: 3 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 134 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw ILAC MRA Table of Contents 1. GENERAL INFORMATION .........................................................................................................6 1.1. Product Description ............................................................................................................................6 1.2. Related Submittal(s) / Grant (s) ..........................................................................................................6 1.3. Test Methodology ...............................................................................................................................6 1.4. Test Facility.........................................................................................................................................6 1.5. Special Accessories .............................................................................................................................6 1.6. Equipment Modifications....................................................................................................................6 2. SYSTEM TEST CONFIGURATION ............................................................................................7 2.1. EUT Configuration .............................................................................................................................7 2.2. EUT Exercise ......................................................................................................................................7 2.3. Test Procedure.....................................................................................................................................7 2.4. Configuration of Tested System..........................................................................................................8 3. SUMMARY OF TEST RESULTS .................................................................................................9 4. DESCRIPTION OF TEST MODES ..............................................................................................9 5. CONDUCTED EMISSION TEST................................................................................................10 5.1. Standard Applicable ..........................................................................................................................10 5.2. EUT Setup.........................................................................................................................................10 5.3. Measurement Procedure....................................................................................................................10 5.4. Measurement Equipment Used: ........................................................................................................11 5.5. Measurement Result..........................................................................................................................11 6. PEAK OUTPUT POWER MEASUREMENT............................................................................14 6.…

Text truncated - open the document above for the full version.