Q54CDR-0130Smart Card Reader

User's Manual For Smart Card Reader(CDR-0130) S1 CORPORATION Smart Card Reader(CDR-0130) Smart card reader is a machine controlling access management and making block mode change in GBMS. Power is supplied by auxiliary power equipment or local controllerII. lock controller. Access management function transmits the data to lock controller as it reads recorded data in card by the method of making customer or traverse card approach to card reader. Lock controller makes access available by controlling lock/auto door of entrance door after checking whether received data is registered or not. Mode change function transmits the data to lock controller as it reads recorded data in card by the method of making customer or traverse card approach to card reader keeping pushed SECOM button of smart card reader. Controller selects guard modes such as set/cancel/traverse by checking whether the received data is registered or not. Use Environment (1) Use temperature : -20°C ∼ ＋45°C (2) Use humidity : 30％ ∼ 90％(relative humidity) (3) Installation requirements － Convenient Place for manipulating machine. － Install on none-metal. － Place which is not affected by raining. － Place which has not direct ray. － Place which is not affected by heat. － Place which has not vibration. － Install at the place that reading distance should be kept more than 5CM. Beep sound & Guiding voice Trough speaker, guiding voice is given as followings. And beep sends confirming sound. Guiding voice Standard Specifications * size : 95(W) × 140(H) × 28(D) 〔mm〕 * Weight : about 234g * Working voltage : DC 17.0 ∼ 28.0V * Current consumption : Power index 1.3 (less than DC 24V 195mA) NO Working Type Working condition Stopping Condition 1 Beep sound At normal input of card data, one time working (ONfor200ms) 2 Guiding voice At card manupulating No guiding voice at normal accessapproval NO Contents Remarks 1 The system has been armed. Set 2 Hello! The system has been disarmed. Cancel 3 Peep! Peep! Peep! You cannot arm the system. Please go inside and check the problem areas. Then run your key cardagain. Troubles 4 There's an error in the card. IC Chip defective 5 The system is armed, please disarm the system. Card working at set 6 Your security card is not valid. Access trying with none-register card 7 Your security card passed its valid date. Card passed its valid date FCC Regulatory Compliance : Notices Class B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio TV technician for help. This device complies with part 15 of the FCC Rules. Operations is subject to the following two conditions : (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: Q54CDR-0130 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Hang-Sik Kang / Sr. Engineer 10 th Fl., Samsung Life Insurance & S1 Bldg. 168, Soonhwa-Dong, Jung-Gu Seoul, Korea 100-130

S1 Corporation FCC ID: Q54CDR-0130 Report No.: R0710022-225 Page 18 of 20 FCC Part 15.225 Report 9 EXHIBIT C - EUT EXTERNAL PHOTOGRAPHS 9.1 EUT - Top View 9.2 EUT – Back View

S1 Corporation FCC ID: Q54CDR-0130 Report No.: R0710022-225 Page 15 of 20 FCC Part 15.225 Report 7 EXHIBIT A - FCC ID LABEL INFORMATION 7.1 FCC ID Label Contents Specifications : Text is black or white in color and is left justified. Labels are silk-screened and shall be “permanently affixed” at a conspicuous location on the EUT. 7.2 Suggested Label Location on EUT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: Q54CDR-0130

S1 Corporation FCC ID: Q54CDR-0130 Report No.: R0710022-225 Page 19 of 20 FCC Part 15.225 Report 10 EXHIBIT C - EUT INTERNAL PHOTOGRAPHS 10.1 EUT – Chassis Cover Off 10.2 EUT – Component View S1 Corporation FCC ID: Q54CDR-0130 Report No.: R0710022-225 Page 20 of 20 FCC Part 15.225 Report 10.3 EUT – Solder View END OF REPORT

Note: This test report is for the customer shown above and their specific product only. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government (REV.1) FCC PART 15.225 MEASUREMENT AND TEST REPORT For S1 Corporation 10th FI., Samsung Life Insurance & S1 Bldg.168, Soonhwa-Dong, Jung-Gu Seoul, Korea 100-130 FCCID: Q54CDR-0130 Model: CDR-0130 Report Type: Original Report Product Type: Smart Card Reader Test Engineer: Jerry Wang Report No.: R0710022-225 Report Date: 2007-10-09 Reviewed By: Samuil Lisinker, Engineering Manager Prepared By: (H2) Bay Area Compliance Laboratories Corp. (BACL) 1274 Anvilwood Ave. Sunnyvale, CA 94089, USA Tel: (408) 732-9162 Fax: (408) 732-9164 S1 Corporation FCC ID: Q54CDR-0130 Report No.: R0710022-225 Page 2 of 14 FCC Part 15.225 Report TABLE OF CONTENTS 1 GENERAL INFORMATION ..............................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ........................................................................3 1.2 EUT PHOTO....................................................................................................................................................3 1.3 MECHANICAL DESCRIPTION............................................................................................................................3 1.4 OBJECTIVE......................................................................................................................................................3 1.5 RELATED SUBMITTAL(S)/GRANT(S)................................................................................................................3 1.6 TEST METHODOLOGY.....................................................................................................................................4 1.7 MEASUREMENT UNCERTAINTY.......................................................................................................................4 1.8 TEST FACILITY................................................................................................................................................5 2 SYSTEM TEST CONFIGURATION .................................................................................................................6 2.1 JUSTIFICATION................................................................................................................................................6 2.2 EUT EXERCISE SOFTWARE.............................................................................................................................6 2.3 SPECIAL ACCESSORIES....................................................................................................................................6 2.4 EQUIPMENT MODIFICATIONS..........................................................................................................................6 2.5 REMOTE SUPPORT EQUIPMENT.......................................................................................................................6 2.6 LOCAL SUPPORT EQUIPMENT..........................................................................................................................6 2.7 TEST SETUP CONFIGURATION.........................................................................................................................7 3 SUMMARY OF TEST RESULTS ......................................................................................................................8 4 § 15.203 – ANTENNA REQUIREMENT ...........................................................................................................9 4.1 APPLICABLE STANDARD.................................................................................................................................9 5 § 15.35, § 15.205, § 15.209, § 15.225 - RADIATED EMISSION TEST ..........................................................10 5.1 EUT SETUP...................................................................................................................................................10 5.2 TEST EQUIPMENT LIST AND DETAILS............................................................................................................10 5.3 TEST PROCEDURE.........................................................................................................................................10 5.4 CORRECTED AMPLITUDE & MARGIN CALCULATION....................................................................................10 5.5 ENVIRONMENTAL CONDITIONS.....................................................................................................................11 5.6 SUMMARY OF TEST RESULTS........................................................................................................................11 6 § 15.225(E) - FREQUENCY STABILITY MEASUREMENT .......................................................................13 6.1 STANDARD APPLICABLE...............................................................................................................................13 6.2 TEST PROCEDURE.........................................................................................................................................13 6.3 TEST EQUIPMENT LIST AND DETAILS............................................................................................................13 6.4 ENVIRONMENTAL CONDITIONS.....................................................................................................................13 6.5 TEST RESULTS..............................................................................................................................................14 S1 Corporation FCC ID: Q54CDR-0130 Report No.: R0710…

Text truncated - open the document above for the full version.

S1 Corporation FCC ID: Q54CDR-0130 Report No.: R0710022-225 Page 16 of 20 FCC Part 15.225 Report 8 EXHIBIT B - TEST SETUP PHOTOGRAPHS 8.1 Radiated Emission below 30 MHz – Front View 8.2 Radiated Emission below 30 MHz – Rear View S1 Corporation FCC ID: Q54CDR-0130 Report No.: R0710022-225 Page 17 of 20 FCC Part 15.225 Report 8.3 Radiated Emission above 30 MHz – Front View 8.4 Radiated Emission above 30 MHz – Rear View