Q5EUP405S01DMR Two Way Radio

UP305/ UP405S DMR Two-way Radio Quick User Guide Please read carefully the Safety Information and Warranty Card before using the product. Caution for Using the Battery  Explosion may be incurred by using a battery of a non-supplied model, or by shorting the anode and cathode of the battery.  Charge the battery using the attached charger, and dispose it as instructed.  Do not strike, squeeze, short out or disassemble the battery.  Do not put the battery in a high temperature or throw it into a fire.  Stop using the battery if it is seriously bulged or immersed in water. Installing the Battery 1. Press the upper part of the belt clip gently so that it goes up. (Figure ①) 2. Align the battery with the battery holder at the back of the radio, and then insert the battery. (Figure ②) 3. Push the battery in the direction indicated until the latch is in position. (Figure ③) 4. Press the upper part of the battery until it is latched. (Figure ④) Installing/Uninstalling the Antenna Insert the threaded end of the antenna into the antenna interface, and rotate the antenna tight clockwise. (Figure 1) To uninstall the antenna, rotate it counterclockwise. (Figure 2) Charging the Battery 1. Plug the power adapter into a qualified AC power socket. 2. Connect the USB cable of the power adapter to the USB port at the back of the desktop charger. Green indicator light is on. 3. Insert the battery only or together with the radio into the charger. 4. Make sure the battery contacts the charging terminals properly and red indicator light is on. 5. When the indicator light turns from red to green, charging is finished. 6. After this, wait 1 to 2 hours before taking out the battery to achieve the best performance. Note: 1. The radio is delivered uncharged. Before using it for the first time, please charge the battery. 2. Always use the supplied lithium battery and desktop charger. 3. A new battery or one that has been stored for more than 2 months after charging needs to be charged for several times to achieve its normal capacity. 4. The maximum operating temperature of the radio is 40 °C。 Installing/Uninstalling Belt Clip Align the two screw holes of the belt clip with the screws holes at the back of the radio, and screw up the screws using a screwdriver. To uninstall the belt clip, unscrew the screws and take off the belt clip. Installing an Earphone (Optional) To use an earphone, open the earphone cover at the upper part of the right side of the radio, and then plug the earphone connector into the jack. Basic Operation 1. Powering On/Off - When the radio is off, hold down the Power/Channel knob for 3 seconds to power on the radio. You will hear a tone “di di”. - When the radio is on, hold down the Power/Channel knob for 3 seconds to power off the radio. You will hear a tone “di di”. 2 Selecting a Channel In standby state, rotate the Power/Channel knob to select a channel. 3. Adjusting the Volume In standby state, press the Volume + key to increase the volume, or the Volume - key to decrease it. 4. Initiating a Call to Default Group Hold down the PTT key to initiate a call and talk, and release it to quit the call. 5. Receiving a Call Green indicator light is on when signals are received. While working on a digital channel, the radio outputs voice when it receives an individual call, group call or all call. While working on an analog channel, the radio outputs voice when it receives signals, and the CTCSS code is the preset one for the channel or analog signaling is disabled for the radio. 6. Answering a Call On a digital channel, you can answer a call by holding down the PTT key within the call duration. After this duration is up, you need to initiate a new call. (Note: You may have the call duration set by your dealer.) On an analog channel, you can answer a call by holding down the PTT key and speaking to the microphone. 7. Digital/Analog Switching After configuring the mode of each channel as analog or digital, you can switch to either mode by selecting a channel using the Power/Channel knob. 8. TOT TOT (Time-out Timer) is to prevent a user from occupying a channel for too long. If the radio transmits continuously for a duration longer than that set by dealer, transmission stops and there is an alert tone, and you may cancel the tone by releasing the PTT key. After a period, you may resume transmission by holding down the key. (Note: You may have this period set by your dealer.) If a pre-alarm is enabled, you hear pre-alarm alert tone before TOT time is up. 9. Scan The radio scans to search for active channels. After finding an active channel, the radio dwells on it for communication. To start/stop scan, press the Function key programmed to scan. 10. Initiating a Call during Scan During scan, you can press the PTT key to transmit on a preset channel. Note: This channel is set by your dealer. 11. Stun/ Revive The radio receives and decodes Kill and Revive signals from another radio, and performs accordingly. When the radio is killed, it receives no signals but Revive. When the radio is revived, it transmits and receives signals normally. Note: This function is available in digital mode only, and is enabled by your dealer. 12. Emergency Alarm Under emergency, you may send an emergency alarm by pressing the Function key programmed to send alarms. To cancel an alarm, press the Function key programmed to exit emergency alarm. You need to set an alarm mode and an alarm type.  Alarm Mode Emergency Alarm: The radio sends an alarm and then exit alarm state automatically. Emergency Alarm + Emergency Call: After the radio sends an emergency alarm, press the PTT key to initiate an emergency call. Emergency Alarm + Auto Background Tone: The radio sends an emergency alarm and then background tone.  Alarm Type None: Alarm is disabled. You cannot send an alarm by pressing the Function key programmed to perform this function. Siren Only: In alarm state, siren plays locally and the control center cannot receive alarm s…

Text truncated - open the document above for the full version.

Kirisun Communication Co., Ltd. * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter July 26, 2023 Nemko North America, Inc. 303 River Road Ottawa K1V 1H2 Canada ATTN.: Reviewing Engineer FCC ID: Q5EUP405S01 FRN: 0008873473 Per section 2.911(d)(7) of the FCC rules, (“ Kirisun Communication Co., Ltd.”) certifies that the equipment for which authorization is sought is designated to the following U.S. Designated agent* for service of process: Company Name: Kirisun Americas LLC Physical U.S. Company Address: 6043 NW 167st Unit A2 HIALEAH, FL 33015-4322 United States Agent name: Carlos Chajin Agent Email Address: [email protected] FRN: 0033737685 The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Designated Agent Signed: (Required, if different to Applicant): Signed: Signed: Printed name: Jessica Wang Printed name: Carlos Chajin Title: Product Manager Title: Vice President Company Name: Kirisun Communication Co., Ltd. Company Name: Kirisun Americas LLC Date: July 26, 2023 Date: 2023-07-26

Kirisun Communication Co., Ltd. Covered Equipment Certification Attestation Letter 7/21/2023 Nemko North America, Inc. 303 River Road Ottawa K1V 1H2 Canada ATTN.: Reviewing Engineer FCC ID: Q5EUP405S01 (Kirisun Communication Co., Ltd.) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. (Kirisun Communication Co., Ltd.) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Signed: Printed name: Jessica Wang Title: Product Manager Company Name: Kirisun Communication Co., Ltd. Date: 7/21/2023

Kirisun Communication Co., Ltd. Add: 3rd Floor, Building A, Tongfang Information Habour, No.11 Langshan Road, Nanshan District, Shenzhen 518057, P.R.China Tel: 0755-86096055 Fax: - Attestation letter FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir/Madam, We, Kirisun Communication Co., Ltd. hereby declare that our product: DMR Two Way Radio FCC ID: Q5EUP405S01 is capable of supporting a voice channel and a minimum data rate of 4800 bits per second per 6.25 kHz of channel bandwidth. DMR interphone’s bandwidth is 12.5 kHz, and it has a double time slot, one is the speech time slot, one is the data time slot, just language sequence is satisfied with 4800 bps/6.25 kHz BW. For Part 90 frequency user, the radio is disabled 25kHz channel bandwidth mode by radio firmware at factory in order to comply with FCC mandate for part 90 frequencies. Sincerely, Jessica Wang Signature: 2023-07-21

Differences Declaration To whom concern, We company Kirisun Communication Co., Ltd. Here by declares: The product model(s) UP305 is the same PCB layout, electronic schematic and Antenna with UP405S, which tested in Shenzhen Huatongwei International Inspection Co., Ltd., the only difference is different model names for commercial purpose. Sincerely yours, Name (in print): Jessica Wang Company name: Kirisun Communication Co., Ltd. Company address: 3rd Floor, Building A, Tongfang Information Habour, No.11 Langshan Road, Nanshan District, Shenzhen 518057, P.R.China Tel: 0755-86096055 E-Mail: [email protected]

Kirisun Communication Co., Ltd. Add: 3rd Floor, Building A, Tongfang Information Habour, No.11 Langshan Road, Nanshan District, Shenzhen 518057, P.R.China Tel: 0755-86096055 Fax: - Extended Frequencies Justification Date: 2023-07-21 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir/Madam, The DMR Two Way Radio, LMR with FCC ID: Q5EUP405S01 was designed to operate in the frequency bands 136~174MHz. To aid equipment authorization in other countries which accept the United States FCC Grant for certification, Kirisun Communication Co., Ltd. is requesting that the FCC lists the frequencies 136~174MHz, under FCC Rules Parts 90 on the FCC Grant. Kirisun Communication Co., Ltd. attests that the radio will not be marketed to USA users with the frequency band which is not allowed by the rule part 90. Per the FCC’s KDB634817 guidance, as an alternative to listing the exact frequencies, we acknowledge that it’s a violation of the FCC Rules if this device operates on unauthorized frequencies. Frequency Range （MHz） FCC Rule Part 136-150 For Federal 150-150.05 For Federal 150.05-150.8 90 150.8-162.0125 90 162.0125-173.2 90 173.2-173.4 90 173.4-174 For Federal Sincerely, Signature: Typed or Printed Name: Jessica Wang E‐mail: [email protected]

2023-07-21 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Shenzhen Huatongwei International Inspection Co., Ltd./ 1/F, Bldg 3, Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, Shenzhen, China / Hans Hu,. to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Kirisun Communication Co., Ltd. / 3rd Floor, Building A, Tongfang Information Habour, No.11 Langshan Road, Nanshan District, Shenzhen 518057, P.R.China. Agency agreement expiration date: 2024-07-21 By: Jessica Wang Signature Printed Title: Product Manager On behalf of : Kirisun Communication Co., Ltd. Telephone: 0755-86096055

2023-07-21 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: Q5EUP405S01 Product Name: DMR Two Way Radio Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description  PCB Layout  PCB Placement  BOM  Tune up These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. By: Jessica Wang Signature Printed Title: Product Manager On behalf of : Kirisun Communication Co., Ltd. Telephone: 0755-86096055

External Photos UP405S UP305

Internal Photos UP405S UP305

Page: 1 of 25 TEST REPORT Report No. ...................................... : CHTEW23070021 Report vertification: Project No. ...................................... : SHT2305086506EW FCC ID ............................................. : Q5EUP405S01 Applicant’s name ........................... : Kirisun Communication Co.,Ltd. Address ............................................. : 3rd Floor, Building A, Tongfang Information Habour, No.11 Langshan Road, Nanshan District, Shenzhen 518057, P.R.China Test item description .................... : DMR Two Way Radio Trade Mark ....................................... : KIRISUN Model/Type reference ....................... : UP405S Listed Model(s) ................................. : UP305 Standard ......................................... : FCC 47 CFR Part2.1093 IEEE Std C95.1, 1999 Edition IEEE 1528: 2013 Date of receipt of test sample.........: Jun.13, 2023 Date of testing.............................: Jun.13, 2023-Jul.07, 2023 Date of issue...............................: Jul.07, 2023 Result .................. ........................: PASS Compiled by (Position-Printed name-Signature) : File administrators Fanghui Zhu Supervised by ( position+printed name+signature) .. : Test Engineer: Xiaodong Zhao Approved by ( position+printed name+signature) .. : Manager: Hans Hu Testing Laboratory Name ............. : Shenzhen Huatongwei International Inspection Co., Ltd Address ............................................. : 1/F, Bldg 3, Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, Shenzhen, China Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. The test report merely correspond to the test sample. Report No.: CHTEW23070021 Page: 2 of 25 Issued: 2023-07-07 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V05 (2023-03) Contents 1. Statement of Compliance 3 2. Test Standards and Report version 4 2.1. Test Standards 4 2.2. Report version 4 3. Summary 5 3.1. Client Information 5 3.2. Product Description 5 3.3. Radio Specification Description 6 3.4. Test frequency list 6 3.5. Testing Laboratory Information 7 3.6. Environmental conditions 7 4. Equipments Used during the Test 8 5. Measurement Uncertainty 9 6. SAR Measurements System Configuration 10 6.1. SAR Measurement Set-up 10 6.2. DASY5 E-field Probe System 11 6.3. Phantoms 12 6.4. Device Holder 12 7. SAR Test Procedure 13 7.1. Scanning Procedure 13 7.2. Data Storage and Evaluation 15 8. Position of the wireless device in relation to the phantom 17 8.1. Front-of-face 17 8.2. Body Position 17 9. Dielectric Property Measurements & System Check 18 9.1. Tissue Dielectric Parameters 18 9.2. SAR System Validation 19 9.3. System Check 19 10. SAR Exposure Limits 22 11. Radiated Power Measurement Results and Tune-up 23 12. SAR Measurement Results 24 13. Test Setup Photos 25 14. External and Internal Photos of the EUT 25 Report No.: CHTEW23070021 Page: 3 of 25 Issued: 2023-07-07 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V05 (2023-03) 1. Statement of Compliance Maximum Reported SAR (W/kg @1g) RF Exposure Conditions TNF Head(Dist.= 25mm) 0.558 Body-worn(Dist.= 0mm) 4.431 Note: 1. This device is in compliance with Specific Absorption Rate (SAR) for occupational/controlled exposure limits (8 W/kg) specified in FCC 47 CFR part 2 (2.1093) and ANSI/IEEE C95.1-1992. 2. This device had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and FCC KDB publications. Report No.: CHTEW23070021 Page: 4 of 25 Issued: 2023-07-07 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V05 (2023-03) 2. Test Standards and Report version 2.1. Test Standards The tests were performed according to following standards: FCC 47 Part 2.1093: Radiofrequency Radiation Exposure Evaluation:Portable Devices IEEE Std C95.1, 1999 Edition: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz IEEE Std 1528™-2013: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques. FCC published RF exposure KDB procedures: KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04: SAR Measurement Requirements for 100 MHz to 6 GHz KDB 865664 D02 RF Exposure Reporting v01r02: RF Exposure Compliance Reporting and Documentation Considerations KDB 447498 D04 Interim General RF Exposure Guidance v01: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies KDB 643646 D01:SAR Test for PTT Radios v01r03: SAR Test Reduction Considerations for Occupational PTT Radios TCB workshop: April, 2019; Page 19, Tissue Simulating Liquids (TSL) 2.2. Report version Revision No. Date of issue Description N/A 2023-07-07 Original Report No.: CHTEW23070021 Page: 5 of 25 Issued: 2023-07-07 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V05 (2023-03) 3. Summary 3.1. Client Information Applicant: Kirisun Communication Co.,Ltd. Address: 3rd Floor, Building A, Tongfang Information Habour, No.11 Langshan Road, Nanshan District, Shenzhen 518057, P.R.China Manufacturer: Kirisun Communication Co.,Ltd. Address: 3rd Floor, Building A, Tongfang Information Habour, No.11 Langshan Road, Nanshan District, Shenzhen 518057, P.R.China 3.2. Product Description Main unit Name of EUT: DMR Two Way Radio Trade Mark: KIRISUN Model No.: UP405S Listed Model(s): …

Text truncated - open the document above for the full version.

Page: 1 of 42 TEST REPORT Report No. ....................................... : CHTEW23070005 Report verification: Project No. ................................. : SHT2305086502EW FCC ID ............................................ : Q5EUP405S01 Applicant’s name ........................... : Kirisun Communication Co.,Ltd. Address.............................................: 3rd Floor, Building A, Tongfang Information Habour, No.11 Langshan Road, Nanshan District, Shenzhen 518057, P.R.China Product name ................................. : DMR Two Way Radio Trade Mark ....................................... : KIRISUN Model No. ......................................... : UP405S Listed Model(s) ................................. : UP305 Standard .......................................... : FCC CFR Title 47 Part 90 Date of receipt of test sample.........: Jun.13, 2023 Date of testing.............................: Jun.13, 2023-Jul.07, 2023 Date of issue...............................: Jul.07, 2023 Result ................. ........................: PASS Compiled by (Position-Printed name-Signature) : File administrators Fanghui Zhu Supervised by (Position-Printed name-Signature) : Project Engineer Caspar Chen Approved by (Position-Printed name-Signature) : RF Manager Hans Hu Testing Laboratory Name .............. : Shenzhen Huatongwei International Inspection Co., Ltd. Address ............................................ : 1/F, Bldg 3, Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, Shenzhen, China Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. The test report merely correspond to the test sample. Report No.: CHTEW23070005 Page: 2 of 42 Issued: 2023-07-06 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V05(2023-03) Contents 1 T E S T S T A N D A R D S A N D RE P O R T V E R S I O N 3 1.1. Test standard 3 1.2. Report revised information 3 2 T E S T D E S C R I P T I O N 4 3 S U M M A R Y 5 3.1 Client information 5 3.2 Product description 5 3.3 Radio Specification Description *1 5 3.4 Testing laboratory information 6 4 T E S T C O N F I G U R A T I O N 7 4.1 Test frequency list 7 4.2 Operation mode 7 4.3 Support unit used in test configuration and system 8 4.4 Testing environmental condition 9 4.5 Measurement uncertainty 9 4.6 Equipment used during the testing 10 5 T E S T C O N D I T I ON S A N D R E S U L T S 11 5.1 Conducted carrier output power 11 5.2 99% occupied bandwidth & 26dB bandwidth 12 5.3 Emission mask 14 5.4 Modulation limit 16 5.5 Audio frequency response 17 5.6 Frequency stability VS temperature 19 5.7 Frequency stability VS voltage 20 5.8 Transmitter frequency behavior 21 5.9 Transmit conducted spurious emission 23 5.10 Transmitter radiated spurious emission 24 6 T E S T S E T U P P H O T O S 33 7 E X T E R N A L A N D I N T E R N AL P H O T O S 34 7.1 External photos 34 1.3. Internal Photos 39 8 A P P E N D I X R E P O R T 42 Report No.: CHTEW23070005 Page: 3 of 42 Issued: 2023-07-06 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V05(2023-03) 1 TEST STANDARDS AND REPORT VERSION 1.1. Test standard The tests were performed according to following standards: FCC Rules Part 90: Private land mobile radio services. FCC Rules Part 2: Frequency allocations and radio treaty matters; General rules and regulations ANSI C63.26-2015: American National Standard for Compliance Testing of Transmitters Used in Licensed Radio Services ANSI/TIA-603-E-2016: Land Mobile FM or PM Communications Equipment and Performance Standards ANSI C63.4-2014: American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz 1.2. Report revised information Revised No. Date of issued Description N/A 2023-07-06 Original Report No.: CHTEW23070005 Page: 4 of 42 Issued: 2023-07-06 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V05(2023-03) 2 TEST DESCRIPTION Section Test Item Section Result Test Engineer 5.1 Conducted carrier output power Part 90.205 Part 2.1046(a) Pass Caspar Chen 5.2 99% occupied bandwidth & 26dB bandwidth Part 90.209 & 210 Part 2.1049 Pass Caspar Chen 5.3 Emission mask Part 90.209 & 210 Part 2.1049 Pass Caspar Chen 5.4 Modulation limit Part 2.1047(b) Pass Caspar Chen 5.5 Audio frequency response Part 2.1047(a) Pass Caspar Chen 5.6 Frequency stability VS temperature Part 90.213 Part 2.1055 Pass Caspar Chen 5.7 Frequency stability VS voltage Part 90.213 Part 2.1055 Pass Caspar Chen 5.8 Transient frequency behavior Part 90.214 Pass Caspar Chen 5.9 Transmit conducted spurious emission Part 90.210 Part 2.1051 Pass Caspar Chen 5.10 Transmit radiated spurious emission Part 90.210 Part 2.1053 Pass Yifan Wang Note: The measurement uncertainty is not included in the test result. Report No.: CHTEW23070005 Page: 5 of 42 Issued: 2023-07-06 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V05(2023-03) 3 SUMMARY 3.1 Client information Applicant: Kirisun Communication Co.,Ltd. Address: 3rd Floor, Building A, Tongfang Information Habour, No.11 Langshan Road, Nanshan District, Shenzhen 518057, P.R.China Manufacturer: Kirisun Communication Co.,Ltd. Address: 3rd Floor, Building A, Tongfang Information Habour, No.11 Langshan Road, Nanshan District, Shenzhen 518057, P.R.China 3.2 Product description Main unit information: Product name: DMR Two Way Radio Trade mark: KIRISUN Model No.: UP405S Listed model(s): UP305 Power s…

Text truncated - open the document above for the full version.

Appendix Report FCC PART 90 Test Form QRE315 V 3.1 (2019-11) Appendix clause Test Result (PASS/FAIL) APASS BPASS CPASS DPASS EPASS FPASS GPASS HPASS IPASS Frequency Stability Test & Temperature Frequency Stability Test & Voltage Transmitter Frequency Behavior Spurious Emission On Antenna Port 6/29 6/29 6/29 6/29 6/29 6/29 7/4 6/29 Audio Frequency Response Occupied Bandwidth Emission Mask Modulation Limit Test Item Test date （M/D) 6/29Maximum Transmitter Power Temperature 24.3°C Test Engineer Humidity Auditor 52% Project No. Test sample No. Start test date YPHT23050865003 Model No. SHT2305086502EW UP405S 2023/6/20 Finish date 2023/7/4 Appendix Page:1 of 27 Project No.:SHT2305086502EW Appendix A:Maximum Transmitter Power Operation Mode Modulation Type Test Channel Measured Power(dBm) Rated Power(W) Percentage(%)Limit (%)Result TX-DNH4FSK CH L 37.05.00-8.80±20PASS TX-DNH4FSK CH M 37.15.00-12.00±20PASS TX-DNH4FSK CH H 37.15.00-6.20±20PASS TX-DNL4FSK CH L 30.01.000.00±20PASS TX-DNL4FSK CH M 30.21.006.00±20PASS TX-DNL4FSK CH H 30.11.001.00±20PASS TX-ANHFM CH L 37.45.0015.00±20PASS TX-ANHFM CH M 37.55.0017.80±20PASS TX-ANHFM CH H 37.55.0015.00±20PASS TX-ANLFM CH L 30.71.0017.00±20PASS TX-ANLFM CH M 30.71.0017.00±20PASS TX-ANLFM CH H 30.71.0017.00±20PASS Appendix Page:2 of 27 Project No.:SHT2305086502EW Appendix B:Occupied Bandwidth 99%(kHz)26dB(kHz) TX-DNH4FSK CH L 7.2399.435 ≤11.25 PASS TX-DNH4FSK CH M 7.0389.270 ≤11.25 PASS TX-DNH4FSK CH H 7.1509.368 ≤11.25 PASS TX-DNL4FSK CH L 7.1109.416 ≤11.25 PASS TX-DNL4FSK CH M 7.0559.260 ≤11.25 PASS TX-DNL4FSK CH H 7.1659.380 ≤11.25 PASS TX-ANHFM CH L 9.89210.140 ≤11.25 PASS TX-ANHFM CH M 9.90310.140 ≤11.25 PASS TX-ANHFM CH H 9.92710.140 ≤11.25 PASS TX-ANLFM CH L 9.90310.140 ≤11.25 PASS TX-ANLFM CH M 9.92710.140 ≤11.25 PASS TX-ANLFM CH H 9.93110.150 ≤11.25 PASS Operation Mode Modulation Type Test Channel 99% Limit(kHz) Result Occupied Bandwidth Appendix Page:3 of 27 Project No.:SHT2305086502EW Appendix B:Occupied Bandwidth Operation Mode Modulation Type Test Channel TX-DNH4FSK CH L TX-DNH4FSK CH M TX-DNH4FSK CH H TEST PLOT RESULT Appendix Page:4 of 27 Project No.:SHT2305086502EW Appendix B:Occupied Bandwidth Operation Mode Modulation Type Test Channel TEST PLOT RESULT TX-DNL4FSK CH L TX-DNL4FSK CH M TX-DNL4FSK CH H Appendix Page:5 of 27 Project No.:SHT2305086502EW Appendix B:Occupied Bandwidth Operation Mode Modulation Type Test Channel TEST PLOT RESULT TX-ANHFM CH L TX-ANHFM CH M TX-ANHFM CH H Appendix Page:6 of 27 Project No.:SHT2305086502EW Appendix B:Occupied Bandwidth Operation Mode Modulation Type Test Channel TEST PLOT RESULT TX-ANLFM CH L TX-ANLFM CH M TX-ANLFM CH H Appendix Page:7 of 27 Project No.:SHT2305086502EW Appendix C:Emission Mask Operation Mode Modulation Type Test Channel TEST PLOT RESULT TX-DNH4FSK CH L TX-DNH4FSK CH L TX-DNH4FSK CH M Appendix Page:8 of 27 Project No.:SHT2305086502EW Appendix C:Emission Mask Operation Mode Modulation Type Test Channel TEST PLOT RESULT TX-DNH4FSK CH M TX-DNH4FSK CH H TX-DNH4FSK CH H Appendix Page:9 of 27 Project No.:SHT2305086502EW Appendix C:Emission Mask Operation Mode Modulation Type Test Channel TEST PLOT RESULT TX-DNL4FSK CH L TX-DNL4FSK CH L TX-DNL4FSK CH M Appendix Page:10 of 27 Project No.:SHT2305086502EW Appendix C:Emission Mask Operation Mode Modulation Type Test Channel TEST PLOT RESULT TX-DNL4FSK CH M TX-DNL4FSK CH H TX-DNL4FSK CH H Appendix Page:11 of 27 Project No.:SHT2305086502EW Appendix C:Emission Mask Operation Mode Modulation Type Test Channel TEST PLOT RESULT TX-ANHFM CH L TX-ANHFM CH L TX-ANHFM CH M Appendix Page:12 of 27 Project No.:SHT2305086502EW Appendix C:Emission Mask Operation Mode Modulation Type Test Channel TEST PLOT RESULT TX-ANHFM CH M TX-ANLFM CH H TX-ANLFM CH H Appendix Page:13 of 27 Project No.:SHT2305086502EW Appendix C:Emission Mask Operation Mode Modulation Type Test Channel TEST PLOT RESULT TX-ANLFM CH L TX-ANLFM CH L TX-ANLFM CH M Appendix Page:14 of 27 Project No.:SHT2305086502EW Appendix C:Emission Mask Operation Mode Modulation Type Test Channel TEST PLOT RESULT TX-ANLFM CH M TX-ANHFM CH H TX-ANHFM CH H Appendix Page:15 of 27 Project No.:SHT2305086502EW Appendix D:Modulation Limit 300Hz1004Hz1500Hz2500 Hz TX-ANHFM CH M -200.09…

Text truncated - open the document above for the full version.