Q6N069ELRemote Control Toy Transmitter

204-11-0085-MANUAL (#EL069) 100% SCALE(mm) PAGE SIZE: 140mm x 200mm 16 34 572 INSTRUCTIONS RC MINI UNDERSEA EXPLORER INSTRUCTIONS CONTENTS BATTERY INSTALLATION Undersea Explorer Diving weight Diving weight (Add one at a time starting from the center andjust) Power switch ON/OFF Head lights Horizontal trim weight cast Right screw forward drive button Antenna Left screw forward drive button Left screw reverse surface button Right screw reverse surface button Diving weight Battery compartment hatch Horizontal weight Transmitter Left screw Right screw BATTERY SAFETY GUIDELINES - To prevent battery leakage: Be sure to insert batteries correctly. - Batteries should be replaced by adult. - Never dispose of batteries in fire as this may cause them to explode. - Do not mix old and new batteries (replace all batteries at the same time). - Do not mix Alkaline, standard (Carbon-Zinc) or rechargeable (Nickel-Cadmium) batteries (or equivalent). Only batteries of the same or equivalent type as recommended are to be used. - Non-rechargeable batteries are not to be recharged. - Always remove exhausted or dead batteries from product. Remove batteries from product which is not going to be used for a long time. Otherwise the batteries may leak and cause damage. - The supply terminals are not to be short-circuited. - Make sure battery compartment is secure. - Do not immerse battery operated toys. Wipe clean only. CLOSEOPEN TRANSMITTER: UNDERSEA EXPLORER: 2) Insert 3 size "AA" (LR6) 1.5 V batteries. 1) Open or close the cover with a Philips screwdriver. 2) Insert 1 9V (6LR61) Alkaline battery. 1) Open or close the cover with a Philips screwdriver. FEATURES - 2-channel,9 functions: submerge, surface, left/right turn, spin turn, stop, etc. - By adjusting the angle of the left/right screws, explorer can ,make a quick dive or quick surface. - The 2-motor system can make the left/right screws turn in opposite directions and thereby enable the explorer to spin turn. - By adjusting the left /right screws at different angles, explorer can make a tornado dive or rolling dive. - If you stop operation, or if the radio waves fail to reach the explorer, the safety system will automatically bring the vessel to the surface. - The hull is water-tight and can submerge to a depth of about 60cm. HOW TO PLAY - Turn the power switch of the undersea explorer On. - Let the explorer float on the Water.(Be sure to adjust the trim.) - After you finish playing, turn the power switch of the explorer OFF and take it out of the water. Transmitter operations and explorer movements (The undersea explorer can sustain submersion to a depth of about 60cm. If you make it dive too deeply, the radio waves will not reach the explorer, and it will go out of control. If you press these button(s), the undersea explorer will: dive forwarddive to the rightdive to the left Surface in the rear directionSurface in the rear rightSurface in the rear left Stop (The explorer's buoyancy will make it surface gradually). Spin turn to the rightSpin turn to the left ADJUSTMENT OF THE ANGLE OF THE LEFT/RIGHT SCREWS (MANUAL) - As can be seen in the diagram, the angle of both screw can be adjusted by hand between 15 and 75. By adjusting both screws at a steep angle of about 75, the explorer can be made to quick dive or quick surface. - If you adjust the screws at small angles. The explorer will not dive or surface so fast, but the forward/ reverse running power will be increased. - By adjusting the left and right screws at different angles (one small and the other at a sharp angle), the explorer will move in a unique manner. Change the angles any way you like and enjoy all sorts of movements. CONTROL DISTANCE AND WATER QUALITY - Depending on the quality of the water, it may be very hard for the radio waves to reach the explorer. Submerge the explorer underwater within your reach, and test the control distance before playing. Muddy or impure water is dense and full of foreign particles, and is not suitable for playing. Choose water which is clear and enables your to see the explorer underwater. POINTS TO BE NOTES (As the battery power runs low, the control distance will become shorter. Shorten the distance between the explorer and transmitter as your playing Time becomes longer.) ¥ Before playing, make sure that the explorer moves according to your trans- mitter operations. ¥ While the explorer is still on land, check the maximum controllable distance Between the explorer and transmitter. When submerged underwater, Leave an allowance and keep the explorer slightly closer to the transmitter than the maximum controllable distance. ¥ If the metal tab in the battery box is deformed and not touching the battery, lift up the tab and adjust properly. ¥ DO NOT play in water that is dirty, has weeds, or obstacles. The filth or weeds may get caught in the screws or other parts and prevent the explorer from moving. ¥ DO NOT play where there is water current, or when the wind is blowing strongly. The explorer may be swept away. ¥ DO NOT play in the ocean(salt water) because the parts will rust. ¥ DO NOT play outdoors in thunderstorms. ¥If the explorer does not move properly, exchange all the batteries in both the explorer and the transmitter. ¥ After playing, remove all the batteries from the transmitter and explorer. Drain out all the water form the explorer and dry completely before storing away. ADJUSTMENT OF THE TRIM AND WEIGHT Make sure that the specified batteries are installed properly, and that the battery compartment hatch is screwed in and locked firmly before putting the explorer into the water. Adjustment of the waterline The buoyancy of the explorer differs depending on the nature of the water. Adjustments should be made in the water where you will actually be playing. Also adjust in shallow water where the explorer is within easy reach. (1) Put the explorer into the water. Adjust the weight so that the waterline(water surface)is within the width of the check line bo…

Text truncated - open the document above for the full version.

     
                !"# !$


 


     %&! &""&  &&'&"()*+&, -. /0 &%&123 /45  $ !066 7  ! /!/0 "/ !/0 0  '6 7 1 8/  !

EL069 Wireless Submarine, 27/49MHz Transmitter Operation Description ©Copyright 2004 EDU-SCIENCE (HK) LIMITED May 26, 2003 Confidential Page 1 of 1 Encoder 27/49MHz Oscillator RF Ampilifier Control CommandsSignal 27/49MHz carrier with modulated signal The Radio Frequency of the transmitter is based on standard 27/49MHz AM (Amplitude Modulation) citizen’s band. It generates low power 27/49MHz AM carrier frequency via major components of Y1, R2, R5, R7, L1, Q1, L6, C10, C11 and C13 (Figure 1). Figure 1 EL069 Wireless Submarine, 27/49MHz Transmitter Operation Description ©Copyright 2004 EDU-SCIENCE (HK) LIMITED May 26, 2003 Confidential Page 2 of 2 The Encoder (U1, Figure 2) reads input commands and modulates these commands (intelligent) with the carrier frequency (as shown in figure 1) via pin 8 (SO, U1, Figure 2) to the RF amplifier. Figure 2 The modulated signal is passed to the final stage of RF amplifier (Figure 3), which amplifies (Q2, R6, C1) the signal and then couples the signal into the antenna (ANT1) via components C3, C6, C7, C8, T1 and L4. Figure 3

Report No.: 04.04.0900EF Page: 1 of 10 FCC ID: Q6N069EL Authorized Signature: Kent Hsu Laboratory Manager SGS-CSTC Co., Ltd. This report refers to the General Conditions for Inspection and Testing Services, printed overleaf This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the SGS PRODUCT CERTIFICATION MARK.. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. Member of the SGS Group (Société Générale de Surveillance) SGS-CSTC Standards Technical Services Ltd. 1/F., Building No. 1 Building, Agriculture Machinery Materials Co. Wushan Road, Shipai, Tianhe District,Guangzhou, China Telephone: +86 (0) 20 3848 1001 Fax: +86 (0) 20 3848 1006 [email protected] FEDERAL COMMUNICATIONS COMMISSION Registration number: 282399 FCC TEST REPORT Application No. : 04.04.0900E (SGS HK No. 2007365/EL) Applicant: EDU-SCIENCE (HK) LTD. FCC ID: Q6N069EL Fundamental Frequency : 27.195MHz Equipment Under Test (EUT): Name: Under Explorer SKU No.: 204110085 (EL069) Standards: FCC PART 15, SUBPART C : 2002 Date of Receipt: 26 & 30 April 2004 Date of Test: 26 to 30 April 2004 Date of Issue: 30 April 2004 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. FCC ID No.: Q6N069EL Report No.: 04.04.0900EF Page: 2 of 10 SGS-CSTC Standards Technical Services Ltd. 2 Contents Page 1 COVER PAGE.........................................................................................................................................................1 2 CONTENTS .............................................................................................................................................................. 2 3 GENERAL INFORMATION.................................................................................................................................. 3 3.1 CLIENT INFORMATION....................................................................................................................................... 3 3.2 DETAILS OF E.U.T. ............................................................................................................................................ 3 3.3 DESCRIPTION OF SUPPORT UNITS....................................................................................................................... 3 3.4 TEST LOCATION................................................................................................................................................. 3 3.5 OTHER INFORMATION REQUESTED BY THE CUSTOMER...................................................................................... 3 3.6 TEST FACILITY................................................................................................................................................... 4 4 TEST RESULTS....................................................................................................................................................... 5 4.1 TEST INSTRUMENTS........................................................................................................................................... 5 4.2 E.U.T. OPERATION............................................................................................................................................ 5 4.3 TEST PROCEDURE & MEASUREMENT DATA....................................................................................................... 5 4.3.1 Radiated Emissions ...................................................................................................................................... 5 4.3.2 Occupied Bandwidth .................................................................................................................................... 7 4.3.3 Photographs - Radiated Emission Test Setup in Chamber ..........................................................................8 5 PHOTOGRAPHS - EUT CONSTRUCTIONAL DETAILS ...........................................................................9-10 FCC ID No.: Q6N069EL Report No.: 04.04.0900EF Page: 3 of 10 SGS-CSTC Standards Technical Services Ltd. 3 General Information 3.1 Client Information Applicant Name: EDU-SCIENCE (HK) LTD. Applicant Address: Suite 701, 7/F, Wing on plaza, 62 Mody Road, TST East, Kln., Hong Kong 3.2 Details of E.U.T. Name: Under Explorer SKU No.: 204110085 (EL069) Power Supply: 9V DC (1 x 'ALKALINE ( 6LR61)' Size Battery) Power Cord: N/A- 3.3 Description of Support Units The EUT was tested as an independent unit: a 27MHz radio transmitter. 3.4 Test Location All tests were performed at:- SGS-CSTC Standards Technical Services Ltd., Guangzhou Safety & EMC Laboratory, 1/F, Building No. 1, Agriculture Machinery Materials Company Warehouse Ltd., Wushan Road Shipai, Tianhe District, Guangzhou, China. P.C. 510630. Tel: +86 20 3848 1001 Fax: +86 20 3848 1006 3.5 Other Information Requested by the Customer None. FCC ID No.: Q6N069EL Report No.: 04.04.0900EF Page: 4 of 10 SGS-CSTC Standards Technical Services Ltd. 3.6 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • NVLAP – Lab Code: 200611-0 SGS-CSTC Standards Technical Services Co., Ltd., Guangzhou EMC Laboratory is recognized under the National Voluntary Laboratory Accreditation Program (NVL…

Text truncated - open the document above for the full version.