Q6WBTP07801Tire pressure monitor system

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) This device must accept any interference received, including interference that may cause undesired operation.2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

GUANGDONG STEELMATE SECURITY CO., LTD 2012-11-07 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certi fication Authority to Act as Agent On our behalf, I appoint China Certi fication & Inspection Services Co., Ltd.; 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China Bruce.Zhang, to act as our agent in the preparation of this application for equipment certification. I certi fy that submitted documents properly describe the device or system for which equipment certi fication is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affi xed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for c erti fication on our behalf, I acknowledge that all responsibilit y for complying with the terms and conditions for certi fication, as specified by Nemko Canada Inc, still resides with GUANGDONG STEELMATE SECURITY CO., LTD Renan Street, Dong Fu Road, Dongfeng Town, Zhongshan City, Guangdong , China. Dated this 2012-11-07 By: Tommy Zhang Signature Printed Title: Manager On behalf of : GUANGDONG STEELMATE SECURITY CO., LTD Telephone: 0760-261-3886

GUANGDONG STEELMATE SECURITY CO., LTD 2012-11-07 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID : Q6WBTP07801 Product Name: Tire pressure monitor system Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the follo wing documents be held confidential: • Schematics • Block diagram • Operation Description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 2012-11-07 By: Tommy Zhang Signature Printed Title: Manager On behalf of : GUANGDONG STEELMATE SECURITY CO., LTD Telephone: 0760-261-3886

Report No: CCIS120100020701 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121000207RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 48 of 56 8 EUT Constructional Details Report No: CCIS120100020701 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121000207RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 49 of 56

Label : Label Location

Report No: CCIS120100020701 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121000207RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 50 of 56 Report No: CCIS120100020701 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121000207RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 51 of 56 Report No: CCIS120100020701 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121000207RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 52 of 56 Report No: CCIS120100020701 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121000207RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 53 of 56 Report No: CCIS120100020701 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121000207RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 54 of 56 Report No: CCIS120100020701 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121000207RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 55 of 56 Report No: CCIS120100020701 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121000207RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 56 of 56 ------End------

No name type ical requi r quantit y reference position remark 1 PCB BTP078A 1 2 chip reststor 0402-12K ±5% SMT 1 R11 3 chip reststor 0402-100K ±5% SMT 3 R10 R26 R25 4 chip reststor 0402-10K ±5% SMT 4 R29 R33 R34 R30 5 chip reststor 0402-220K ±5% SMT 1 R7 6 chip reststor 0402-10R ±5% SMT 1 R4 R20 7 chip reststor 0402-2K2 ±5% SMT 2 R28 R27 8 chip Capacitor 0402-C104(0.1uF) 10V 10% X7R SMT 5 C27 C20 C30 C17 C32 9 chip Capacitor 0402-C27P SMT 1 C24 10 chip Capacitor 0402-103(10nF) 50V 10% X7R SMT 1 C15 11 chip Capacitor 0402-105(1UF/6.3V) SMT 1 C34 12 chip reststor 0402-47K ±5% SMT 2 R16 R17 13 chip Capacitor 0603-C105(1UF)(25V) SMT 1 C28 14 chip Capacitor 0805-C106(10UF/25V) SMT 1 C33 15 chip Capacitor 1206-C106 X5R(10UF/25V) SMT 1 C31 16 SMT IC SGM358 MSOP-8 SMT 1 U5 17 chip Capacitor 10uF/10V A SMT 1 C16 chip diode IN4148WT/T4 SOD-523 SMT 2 D5 D6 19 chip reststor 0402-0R ±5% SMT 1 L4 20 chip reststor 0402-100R ±5% SMT 2 R35 R36 21 chip Capacitor 100uF/6.3V B SMT 1 C36 22 SMT IC BM57SPPS05 Bluetooth Module SMT 1 U4 23 SMT IC MFI337A SMT 1 U6 1 PCB BTP089A 2 layers 1 2 chip reststor 0402-12K ±5% SMT 1 R2 3 chip reststor 0402-180K ±5% SMT 1 R1 4 chip reststor 0402-1K ±5% SMT 2 R8 R3 5 chip reststor 0402-33K ±5% SMT 1 R15 6 chip reststor 0402-470K ±5% SMT 1 R19 7 chip reststor 0805-10R ±5% SMT 1 R5 8 chip reststor 1206-1K ±5% SMT 1 R9 9 chip Capacitor 0402-100p SMT 1 C7 10 chip Capacitor 0402-104 10V 10% X7R SMT 4 C8 C14 C4 C19 11 chip Capacitor 0402-C180P SMT 1 C3 12 chip Capacitor 0402-223 SMT 1 C9 13 chip Capacitor 0402-27P SMT 1 C2 14 chip Capacitor 0402-2P SMT 1 C1 15 chip Capacitor 0402-3P SMT 2 C10 C11 16 chip Capacitor 0402-683 SMT 3 C6 C5 C12 17 chip Capacitor 0603-180P SMT 1 C13 18 chip Capacitor 0805-106 SMT 1 C21 19 chip inductance 0402-12nH SMT 1 L1 20 chip inductance 0402-39nH SMT 1 L3 21 chip inductance 0402-47nH SMT 1 L2 22 self comeback fuse 1206(0.35A/13.2V) SMT 1 F1 23 SMT IC ATA5428-PLHW SMD SMT 1 U1 24 SMT IC HT7333 SMT 1 U2 25 chip tantalum Capacitor 100uF/6.3V B SMT 1 C22 26 chip tantalum Capacitor 10uF/20V B SMT 1 C23 27 chip transistor MAR1A (SOT-23) SMT 1 Q4 29 chip transistor MPS8050S-D SOT-23 SMT 1 Q5 30 crystal oscillator 13.25311MHz 5032 SMD SMT 1 X1 31 chip diode BZV55-C24 SMT 1 D2 32 chip diode CRS04 SMT 1 D1 33 buzz ATI-0903A-A3 DIP 1 BUZZ 38 DIP capacitance 47uF/25V DIP 1 C37 1 PCB BTP082A 2 layers 1 2 chip reststor 0603-2K2 SMT 1 R23 3 chip reststor 0603-470R SMT 2 R6 R12 4 chip Capacitor 0402-104 10V 10% X7R SMT 2 C35 C25 5 chip LED 0603-blue SMT 1 LED3 6 SMT IC PIC16F1938 SMT 1 U7 7 SMT Switch SKQTLAE010 SMT 1

According to KDB 447498 3) Transmitters and modules for use in portable exposure conditions that allow simultaneous transmission a) Except during network hand-offs where the maximum hand-off duration is less than 30 seconds, simultaneous transmission applies when there is overlapping transmission. SAR is evaluated for simultaneous transmission using volume scan measurements. b) SAR is not required for the following simultaneous transmission conditions i) When excluded by the procedures in KDB 616217 or KDB 648474. ii) When specific requirements for simultaneous transmission SAR evaluation have not been established for the host platform or device configuration: (1) for the antennas that are located < 5 cm from persons, where (a) The closest antenna separation distance is ≥ 5 cm for all simultaneous transmitting antennas within the host or device; and (b) The sum of the 1-g SAR is < 1.6 W/kg for all simultaneous transmitting antennas that require stand-alone SAR evaluation or the SAR to peak location separation ratios are< 0.3 for all simultaneous transmitting antenna pairs;18 and (c) The output power is ≤ 60/f(GHz) mW for any simultaneous transmitting antenna(s) for which stand-alone SAR evaluation is not required. The EUT is a stand‐alone transmitter, and its maximum output power = 0.89 dBm = 1.23 mW, 60/f (GHz) = 24.5 mW, the maximum output power of EUT < 60/f (GHz). So the SAR evaluation is exempt.

China Certification & Inspection Services Co., Ltd. Report No: CCIS12100020702 Authorized Signature: Bruce Zhang Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the CCIS product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 1 Cover Page FCC REPORT Applicant: GUANGDONG STEELMATE SECURITY CO., LTD. Address of Applicant: Renan Street, Dong Fu Road, Dongfeng Town, Zhongshan City, Guangdong, China. Equipment Under Test (EUT) Product Name: Tire pressure monitor system Model No.: TPMS8886 Trade mark: Steelmate FCC ID: Q6WBTP07801 Applicable standards: FCC CFR Title 47 Part 15 Subpart B: 2011 Date of sample receipt: 22 Oct., 2012 Date of Test: 23 to 05 Nov., 2012 Date of report issued: 06 Nov., 2012 Test Result : Pass * * In the configuration tested, the EUT complied with the standards specified above. Report No: CCIS12100020702 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121000207RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2311 8282 Fax: +86 (0) 755 2311 6366 Page 2 of 15 2 Version Version No. Date Description 00 06 Nov., 2012 Original Prepared By: Date: 06 Nov., 2012 Project Engineer Check By: Date: 06 Nov., 2012 Reviewer Report No: CCIS12100020702 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121000207RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2311 8282 Fax: +86 (0) 755 2311 6366 Page 3 of 15 3 Contents Page 1 COVER PAGE.........................................................................................................................................................1 2 VERSION..................................................................................................................................................................2 3 CONTENTS..............................................................................................................................................................3 4 TEST SUMMARY....................................................................................................................................................4 5 GENERAL INFORMATION...................................................................................................................................5 5.1 CLIENT INFORMATION....................................................................................................................................... 5 5.2 GENERAL DESCRIPTION OF E.U.T................................................................................................................... 5 5.3 OPERATING MODES.......................................................................................................................................... 5 5.4 DESCRIPTION OF SUPPORT UNITS................................................................................................................... 6 5.5 DEVIATION FROM STANDARDS.......................................................................................................................... 6 5.6 ABNORMALITIES FROM STANDARD CONDITIONS.............................................................................................. 6 5.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER.................................................................................. 6 5.8 TEST FACILITY................................................................................................................................................... 6 5.9 TEST LOCATION................................................................................................................................................ 6 6 TEST INSTRUMENTS LIST..................................................................................................................................7 7 TEST RESULTS AND MEASUREMENT DATA................................................................................................8 7.1 RADIATED EMISSION......................................................................................................................................... 8 8 TEST SETUP PHOTO..........................................................................................................................................14 9 EUT CONSTRUCTIONAL DETAILS.................................................................................................................15 Report No: CCIS12100020702 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121000207RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2311 8282 Fax: +86 (0) 755 2311 6366 Page 4 of 15 4 Test Summary Test Item Section in CFR 47 Result Conducted Emission Part15.107 N/A Readiated Emissions Part15.109 Pass Pass: The EUT complies with the essential requirements in the standard. N/A: Not applicant for product power by battery. Report No: CCIS12100020702 China Certific…

Text truncated - open the document above for the full version.

Report No: CCIS12100020702 China Certification & Inspection Services Co., Ltd. Project No.: CCIS121000207RF 1st Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2311 8282 Fax: +86 (0) 755 2311 6366 Page 14 of 15 8 Test Setup Photo Radiated Emission