Q78-V6000Dual-Band GSM and Dual-Band WCDMA Digital Mobile Phone

-0- ZTE V6000 User Manual -1- Using your phone Thanks for choosing the ZTE V6000. It’s a WCDMA digital mobile phone, which we’ll simply call ‘phone’ from now on.Under Android operating system, the mobile phone supports 3G high-speed Internet access, which brings you brandnew experiences. And don’t worry if the pictures we use to demonstrate your phone’s functions look a little different from what you see on its screen. It’s the functions they show that matter. This quick start guide is designed to help you familiarise yourself with the mobile phone’s basic functions. For details, please refer to the User Manual. -2- Starting Up How to insert the SIM card Insert the SIM card as follows: 1. Switch off your phone and disconnect any external power. 2. Remove the back cover and then the battery. 3. Hold your SIM on the cut corner, and slide it face down into the card holder. 4. Insert the battery. 5. Replace the back cover. Inserting and removing a memory card Note: Removing or inserting a memory card when your phone is turned on could not only damage it and your phone, but also destroy any data saved on the card. 1. Remove the back cover and insert the memory card at the side of the phone. 2. Push tightly until the card is installed in the right position and replace the back cover. 3. Before you take out the card, please open the back cover and press the card inward to unlock. -3- Battery The lithium ion battery of the mobile phone can be immediately used after unpacking. A new battery performs best after perfoming a full charge/discharge 3 times. Installing the battery 1. Open the battery cover on the back of your phone. 2. Align the battery's contact points with those of the phone and gently press the battery down into place. 3. Replace the battery cover clicking it back into position. Removing the battery 1. Switch off your phone. 2. Open the battery cover. 3. Lift the battery up and out of your phone. -4- How to charge the battery The rechargeable Li-ion battery that comes with your phone is ready to use, but is not charged. That’s easy to do. We’ll show you how below. 1. Connect the charger to your phone, and plug it into an 110V/220V socket. 2. The battery indicator in the corner of the screen will scroll to show you it’s charging. 3. When fully charged, the battery indicator will stop scrolling. Disconnect the charger from your mobile, and unplug. Powering On/Off Powering On Press the End/Power key until the power-on icon appears. Note:You may need to enter the Personal Identification Number (PIN) or Draw unlock pattern if you have set a PIN or unlock pattern. Powering Off Long press the End/Power key to display the menu Phone options and select Power off. -5- My Phone End/power key Back key Home key Menu key OK key Side keys Fn key SYM key Delete key Receiver Camera Speaker USB interface Headset jack End/power key Press the key to turn on/off the display, and hold the key to turn on/off the phone. Side keys Adjust the volume -6- Idle screen When you turn on the phone, it enters the idle screen. The following indicators notify you with the phone status and alerts. Icons Descriptions IconsDescriptions Signal strength No signal Battery is full In charging Battery is low In call 3G connected GPRS connected Edge connected You have unread message. Speakerphone is on You have unheard voice mail. Call forwarding is on You have unread email. Call on hold Connected to a PC Vibrate mode Music playing Ringer is silenced New calendar reminder Flight mode A clock alarm is active. Missed call WLAN function on Bluetooth is on Receiving location data from GPS -7- Text Input Using the keypad As the slide is opened, you could use the keypad to input.  Switch input method: Press the key.  Insert a space: Press the key.  Delete: Press the key to delete the input before the cursor.  Switch caps lock: Press the key.  Line feed: Press the key.  Input letters and common symbols: There are two symbols on the keys. In abc/Abc/ABC method, press the key to input the symbol located on the left part of the key; press the key and then press the key to input the symbol located on the right part of the key; press the key twice and then press the key to continuously input the symbol located on the right part of the key. In Smart abc/Abc/ABC method, your phone predicts the word as you enter it, so you need input only the first few letters of the word.  Input numbers: In 123 method, press the numeric keys to input the corresponding numbers.  Input symbols: During the text input, press key to display symbol lists, press the Navigation keys to select the symbol, and press OK to confirm. -8- Using Virtual keyboard Your phone supports the Android keyboard input method and the TouchPal keyboard input method. Android keyboard supports multiple language inputs; TouchPal keyboard supports English and Spanish. On the text screen, touch and hold the space where you usually write your text until the Input method is displayed,and touch it and select the input options. Android Keyboard XT9 Text Input XT9 Text Input can speed up text input by replacing the key tapping motion of input with a tracing gesture where you move your finger from letter to letter without lifting the finger until you reach the end of the word. Delete a character before Insert a smiley. Change between lowercase and uppercase. Change to symbol/number mode. Tap again to change Select input methodInsert space -9- Basic Operation Make and answer calls Make a call Directly make a call  On the home screen, press the numeric keys to input the telephone numberand press the button to make a call. Making a call from Contacts  In the Launcher, press the Contacts icon to display the list of contacts, select the desired contact and press button to make a call. Making a call from Calls  In the Launcher, press Contacts > Calls to select the desired call log and press button to make a call. Make an international call  Long press “0” key until “+” appears on the scr…

Text truncated - open the document above for the full version.

Rev. 1/1/03 ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China Tel: +86-755-86360379 ; Fax: +86-755-86360298 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: Q78-V6000 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Schematics (file: ZTE V6000_Schem.pdf) Block Diagram (file: ZTE V6000 _BlkDia.pdf) Parts List (file: ZTE V6000_PartsLst.pdf) Operation Description (file: ZTE V6000 _OpDes.doc) Tune Up Procedure (file: ZTE V6000 _TunPro.doc) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, David Gong

1/1 ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China Tel: +86-755-86360379 ; Fax: +86-755-86360298 Date: February 8, 2012 Federal Communications Commission Authorization and Evaluation Division RE : Certification Application FCC ID : Q78-V6000 To Whom It May Concern, Pursuant to sections 0.457 and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 180 days:  External Photos (file: ZTE V6000_ExtPho.pdf)  Internal Photos (file: ZTE V6000_IntPho.pdf)  Test Setup Photos (file: ZTE V6000_Tsup.pdf)  User Manual (file: ZTE V6000_UserMan.pdf) The application contains technical information, which ZTE CORPORATION deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, David Gong

ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China Tel: +86-755-86360379 ; Fax: +86-755-86360298 Date: February 8, 2012 Power of Attorney To whom it may concern, Please be notified that I, Royce Wang, have designated Xuewen.Wu in Shenzhen Morlab Communications Technology Co., Ltd. and David Gong in ZTE CORPORATION as the persons being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Xuewen.Wu in Shenzhen Morlab Communications Technology Co., Ltd., and David Gong in ZTE CORPORATION on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This authorization is limited to the product of as following: FCC ID: Q78-V6000 If you have any acknowledgement and response, please send it to Shenzhen Morlab Communications Technology Co., Ltd. directly. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, Contact Person: Royce Wang Company: ZTE CORPORATION TEL: +86-755-86360379 FAX: +86-755-86360298 E-mail: [email protected]

Date: February 8, 2012 Equipment Authorization Division Office of Engineering and Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: Q78-V6000 Dear Sirs: ZTE Cooperation requests acceptance of the labeling proposal described below for cell phone bearing FCC identifier Q78-V6000. The subject cell phone are compact handheld models as shown in figure 1, authorized under 47CFR Part 22H&24E for GSM and WCDMA mobile services. Figure 1. Because the majority of the cell phone housing is composed of display, speaker, operating controls and a removable battery pack, there is extremely limited space available to attach the required label carrying the FCC identifier. Attaching the label to the battery pack is not acceptable because the battery pack is a removable item. For this reason, ZTE Cooperation proposes placing the label carrying the FCC identifier inside the battery compartment as shown in figure 2. Figure 2. The consumer packaging for these models includes the battery pack as a separate item, NOT installed on the radio. As such, the FCC identifier will be readily visible to the user before the battery pack is installed and whenever the battery pack is removed or replaced. In this location, the label will also be protected from physical abuse and remain readable for the anticipated life of the device. The consumer packaging for these models is a "gift box" which does not allow the transceiver to be seen at time of purchase. In order to meet the requirements of 47CFR Part 2.925 (d), ZTE Cooperation will add the FCC identifier " Q78-V6000 " to the outside of the consumer "gift box" packaging. Thank you for your attention to this matter. Yours Sincerely, David Gong

External Photos

FCC ID: Q78-V6000 Label Label Location

Internal Photos

SZ11120159S01 Page 2 of 168 DIRECTORY TESTING LABORATORY ............................................................................................................. 4 1.1. Identification of the Responsible Testing Laboratory ......................................................... 4 1.2. Identification of the Responsible Testing Location .............................................................. 4 1.3. Accreditation Certificate ........................................................................................................ 4 1.4. List of Test Equipments .......................................................................................................... 4 2. TECHNICAL INFORMATION ............................................................................................... 5 2.1. Identification of Applicant ..................................................................................................... 5 2.2. Identification of Manufacturer .............................................................................................. 5 2.3. Equipment Under Test (EUT) ................................................................................................ 5 2.3.1. Photographs of the EUT .................................................................................................. 5 2.3.2. Identification of all used EUT ......................................................................................... 5 2.4. Applied Reference Documents ............................................................................................... 6 2.5. Device Category and SAR Limits .......................................................................................... 6 2.6. Test Environment/Conditions ................................................................................................ 7 3. SPECIFIC ABSORPTION RATE (SAR) ................................................................................ 8 3.1. Introduction ............................................................................................................................. 8 3.2. SAR Definition......................................................................................................................... 8 4. SAR MEASUREMENT SETUP ............................................................................................... 9 4.1. The Measurement System ...................................................................................................... 9 4.2. Probe ........................................................................................................................................ 9 4.3. Probe Calibration Process .................................................................................................... 11 4.3.1 Dosimetric Assessment Procedure ........................................................................................ 11 4.3.2 Free Space Assessment Procedure ........................................................................................ 11 4.3.2 Temperature Assessment Procedure..................................................................................... 11 4.4. Phantom ................................................................................................................................. 12 4.5. Device Holder ........................................................................................................................ 12 5. TISSUE SIMULATING LIQUIDS ......................................................................................... 13 6. UNCERTAINTY ASSESSMENT ........................................................................................... 15 6.1. UNCERTAINTY EVALUATION FOR HANDSET SAR TEST ...................................... 15 6.2. UNCERTAINTY FOR SYSTEM PERFORMANCE CHECK ........................................ 16 7. SAR MEASUREMENT EVALUATION ............................................................................... 18 SZ11120159S01 Page 3 of 168 7.1. System Setup .......................................................................................................................... 18 7.2. Validation Results .................................................................................................................. 19 8. OPERATIONAL CONDITIONS DURING TEST ................................................................ 20 8.1. Informations on the testing .................................................................................................. 20 8.2. Body-worn Configurations ................................................................................................... 21 8.3. Measurement procedure ....................................................................................................... 21 8.4. Description of interpolation/extrapolation scheme ............................................................ 22 9. 3G MEASUREMENT PROCEDURES .................................................................................. 23 9.1. Procedures Used To Establish Test Signal .......................................................................... 23 9.2. SAR Measurement Conditions for WCDMA ..................................................................... 23 9.3. Output Power Verification ................................................................................................... 23 9.4. Measurement Of Conducted Peak Output Power. ............................................................. 24 10. WIRELESS HOT SPOT SAR EVALUATION PROCEDURES ......................................... 28 11. TEST RESULTS LIST ............................................................................................................. 29 12. SCALED SAR LIST ................................................................................................................. 33 13. MULTIPLE TRANSMITTERS EVALUATION ..................................…

Text truncated - open the document above for the full version.

 Ref: CR-280-1-08-SATB-A COMOSAR E-Field probe Calibration Report         1    COMOSAR E-FIELD PROBE CALIBRATION REPORT Prepared By: LUC Jérôme, SATIMO Project Description: SAR TEST BENCH Prepared For (End User): Shenzhen Morlab Communication Technology          This document is issued by SATIMO, in confidence and is not to be reproduced in whole or in part without the prior written permission. The information contained herein is to be used only for the purpose for which it is submitted and is not to be released in whole or in part without the prior written permission of SATIMO.  Ref: CR-280-1-08-SATB-A COMOSAR E-Field probe Calibration Report         2  COMOSAR SEPT ISOTROPIC E-FIELD PROBE CALIBRATION REPORT DATE: 12/02/2009 REFERENCE: SN 37/08 EP80 OBJECT: COMOSAR SEPT ISOTROPIC E-FIELD PROBE MANUFACTURER: SATIMO SERIAL NUMBER: SN 37/08 EP80 CUSTOMER: Shenzhen Morlab Communication Technology CONTRACT: PF2130108b_SAR_Morlab DATE OF CALIBRATION: 24/09/20 WARRANTY: This Calibration certificate may not be reproduced other than in full. Calibration certificates without signature and seal are not valid. This documentation contains property information which is protected by copyright. All right are reserved. No part of this document may be photocopied, reproduced without the prior written agreement of SATIMO. SATIMO shall not be liable for errors contained herein or for incidental or consequential in connection with the furnishing, performance or use of this material. Warranty doesn’t apply to Normal wear, Normal tear, Improper use, Improper maintain, Improper installation. Date SAR TEAM MANAGER Date SAR TEAM MANAGER  Ref: CR-280-1-08-SATB-A COMOSAR E-Field probe Calibration Report         3  PRODUCT DESCRIPTION Frequency Range 100 MHz - 30 GHz Probe length 330 mm Length of one dipole 4.5 mm Maximum external diameter 8 mm Probe extremity diameter 6.5 mm Distance between dipoles/probe extremity < 2.7 mm Resistance of the three dipole (at the connector) Dipole 1: R1=1.4382 MΩ Dipole 2: R2=1.4894 MΩ Dipole 3: R3=1.4683 MΩ Connector (HIROSE series SR30) 6 wire male (Hirose SR30series) The probe could be checked by measuring the resistance of the three dipoles. CALIBRATION TEST EQUIPMENT TYPE IDENTIFICATION Calibration bench CALISAR Multimeter Keithley 2000  Ref: CR-280-1-08-SATB-A COMOSAR E-Field probe Calibration Report         4  MEASUREMENT PROCEDURE Probe calibration is realized, in compliance with CENELEC EN 50361 and IEEE 1528 std, with CALISAR, Antennessa proprietary calibration system. The calibration is performed with the EN 50361 annexe technique using reference guide at the five frequencies. Where : P fw = Forward Power P bw = Backward Power a and b = Waveguide dimensions
= Skin depth Keithley configuration: Rate = Medium; Filter =ON; RDGS=10; FILTER TYPE =MOVING AVERAGE; RANGE AUTO After each calibration, a SAR measurement is performed on a validation dipole and compared with a NPL calibrated probe, to verify it.  Ref: CR-280-1-08-SATB-A COMOSAR E-Field probe Calibration Report         5  PROBE UNCERTAINTIES  Ref: CR-280-1-08-SATB-A COMOSAR E-Field probe Calibration Report         6  1. Calibration at 450.00 MHz A. Calibration parameters. Label GSM450 Epsilon 43.33 Sigma 0.84 S/m Temperature 21°C Antenna gain 2.03 dB Antenna S11 -10.50 dB Low limit detection (CW)     Calibration curves ei=f(V) (i=1,2,3) allow to obtain E-field value using the formula:   EEEE= The following tables represent the calibration curves linearization by curve segment in CW signal.  Ref: CR-280-1-08-SATB-A COMOSAR E-Field probe Calibration Report         7  Calibration coefficients for the three dipoles in CW: v1 e1 v2 e2 v3 e3 0.584004 419.557857 -0.696059 435.622023 0.541191 412.830715 0.467833 339.207465 -0.556278 351.381991 0.469757 336.297240 0.376994 276.348283 -0.452232 288.647980 0.378826 274.224190 0.302778 224.954643 -0.359005 232.397390 0.305842 224.365698 0.241038 182.154071 -0.286978 188.889931 0.246562 183.825274 0.192549 148.484090 -0.230386 154.650994 0.195712 148.993075 0.154033 121.674762 -0.185412 127.378480 0.157543 122.783107 0.123397 100.276479 -0.147311 104.193802 0.125866 100.956090 0.099878 83.770361 -0.118637 86.660489 0.101471 84.063863 0.081165 70.553219 -0.095250 72.263937 0.082289 70.694342 0.065166 59.152028 -0.076788 60.795323 0.066427 59.538957 0.051916 49.592416 -0.061280 51.041514 0.053353 50.232492 0.041968 42.297602 -0.048746 43.022565 0.042906 42.675214 0.033724 36.126757 -0.039149 36.748110 0.034686 36.605243 0.021855 26.962568 -0.024798 27.024723 0.022272 27.149463 0.018405 23.975145 -0.020856 24.085809 0.018755 24.141334 0.015467 21.515985 -0.017534 21.515985 0.015767 21.615299 0.013018 19.309065 -0.014750 19.398191 0.013276 19.487731 0.010938 17.408496 -0.012392 17.529166 0.011157 17.569575 0.009022 15.586953 -0.010228 15.658899 0.009215 15.676938 0.007353 13.956010 -0.008328 13.988181 0.007484 14.020428 0.005989 12.466979 -0.006801 12.495719 0.006111 12.567858 0.004890 11.214019 -0.005573 11.265779 0.005003 11.330818 0.004019 10.133541 -0.004570 10.121882 0.004099 10.168601 0.003279 9.094132 -0.003739 9.157170 0.003352 9.125596 0.002660 8.095827 -0.003041 8.293946 0.002769 8.265350 0.002126 7.324219 -0.002453 7.366500 0.002188 7.358024 0.001685 6.565400 -0.001947 6.580536 0.001724 6.542765 0.001300 5.784440 -0.001511 5.718225 0.001334 5.757862 0.001123 5.245191 -0.001307 5.269400 0.001174 5.275471 0.000891 4.701768 -0.001057 4.723470 0.000924 4.728912 0.000704 4.209798 -0.000850 4.226839 0.000736 4.243862 0.000574 3.790376 -0.000689 3.791428 0.000603 3.830551 0.000457 3.396200 -0.000570 3.434303 0.000483 3.421852 0.000365 3.050686 -0.000463 3.078014 0.000389 3.079630 0.000292 2.745766 -0.000369 2.726866 0.00031…

Text truncated - open the document above for the full version.

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

 Ref: CR-280-7-08-SATB-A COMOSAR Dipole 2450 MHz Calibration Report                    DIPOLE 2450 MHZ CALIBRATION REPORT   !"# $% &'( ())&*"+#,"#,-. /&0,* 1 "2*32*$&45& *)()&*#(2*&4&             #2) &( *) ) 5"# $%!)*(&*6)*(*) *&&5& ()*72&4&)* 7)2& 2)&7)* ) )&*8#2)*6& )&*(&*)* 2)*) & 5 &*46&2  & 6&72)(2))  5 )*) *&&54 )*72&4&)*7)2& 2)&7)*  ) )&*&6"# $%8  Ref: CR-280-7-08-SATB-A COMOSAR Dipole 2450 MHz Calibration Report          DIPOLE 2450 MHz CALIBRATION REPORT DATE    REFERENCE"- 9 :    OBJECT%$%"+ ,,,+,/,+,-, %,  MANUFACTURER"# $%  SERIALNUMBER"- 9 :    CUSTOMER"2*32*$&45& *)()&*#(2*&4&  CONTRACT/ :5;"+;$&45  DATE OF CALIBRATION    WARRANTY: #2) 4)5)&*()6)( *&5& (&22*)*6 4484)5)&*()6)(  7)2&  )* * 4*&<4)8#2) &( *)&*(&*)* &)*6& )&*72)(2)  &( 5 (&)28 44 )2   <8 -&  &6 2)  &( *  5 2&&(&)! & (7)2& 2)&7)* *&6"# $%8"# $% 244*&54)546&&  (&*)*2)*&6&)*()*4&(&* = *)4)*(&**()&*7)226 *) 2)*!6& *(& &62)  )48>*& *?4&-& 47!-& 4! & ! & )*)*! &)* 44)&*8      "+#,$$-@,+   "+#,$$-@,+  Ref: CR-280-7-08-SATB-A COMOSAR Dipole 2450 MHz Calibration Report         PRODUCT DESCRIPTION  CALIBRATION TEST EQUIPMENT TYPE IDENTIFICATION A(&-7&B*43.:CD    MEASUREMENT PROCEDURE  >4(2)&4 *264&6"$2*& 6)447)2D$.324)= )8  E ! E E D E  ED E ED E ED  ! D!DD Frequency (GHz) S11 (dB)   VSWR at 2450 MHz: -33.09 dB.

Report No.: SZ11120159E01 …

Text truncated - open the document above for the full version.