Q78-V6700CDMA2000 DIGITAL MOBILE PHONE

ZTE V6700 User Manual -1- Using your phone Thanks for choosing the ZTE V6700. It’s a CDMA2000 1X EVDO digital mobile phone, which we’ll simply call ‘phone’ from now on. Under Android operating system, the phone supports 3G high-speed Internet access, which brings you brand new experiences. And don’t worry if the pictures we use to demonstrate your phone’s functions look a little different from what you see on its screen. It’s the functions they show that matter. -2- Starting Up How to insert the UIM card 1. Switch off your phone and disconnect any external power. 2. Remove the back cover and then the battery. 3. Hold your UIM on the cut corner, and slide it face down into the card holder. 4. Insert the battery. 5. Replace the back cover. Inserting and removing a memory card Note: Removing or inserting a memory card when your phone is turned on could not only damage it and your phone, but also destroy any data saved on the card. 1. Remove the back cover and insert the memory card at the side of the phone. 2. Push tightly until the card is installed in the right position and replace the back cover. 3. Before you take out the card, please open the back cover and press the card inward to unlock. -3- Battery The lithium ion battery of the mobile phone can be immediately used after unpacking. A new battery performs best after performing a full charge/discharge 3 times. Installing the battery 1. Open the battery cover on the back of your phone. 2. Align the battery's contact points with those of the phone and gently press the battery down into place. 3. Replace the battery cover clicking it back into position. Removing the battery 1. Switch off your phone. 2. Open the battery cover. 3. Lift the battery up and out of your phone. -4- How to charge the battery The rechargeable Li-ion battery that comes with your phone is ready to use, but is not charged. That’s easy to do. We’ll show you how below. 1. Connect the charger to your phone, and plug it into an 110V/220V socket. 2. The battery indicator in the corner of the screen will scroll to show you it’s charging. 3. When fully charged, the battery indicator will stop scrolling. Disconnect the charger from your mobile, and unplug. Powering On/Off Powering On Press the End/Power key until the power-on icon appears. Note:You may need to enter the Personal Identification Number (PIN) or Draw unlock pattern if you have set a PIN or unlock pattern. Powering Off Long press the End/Power key to display the menu Phone options and select Power off. -5- Search Key Touch screen Menu key Back key Home key Earpiece Speaker Camera Powerkey Headset jack Volume keys USB port Flashbulb My Phone -6- Onscreen icons Icons Descriptions IconsDescriptions Signal strength No signal Full battery Charging Low battery In a call Connected on 3G You have an unread message. Speakerphone on You have an unheard voicemail. Call forwarding on You have an unread E-mail. No memory card You have an unread G-mail. Call held Connected to a PC Vibration mode Music playing Silence mode New calendar reminder Flight mode Alarm clock on Missed calls Wi-Fi function on Bluetooth ® function is on Receiving location data from GPS Roaming -7- Basic Operation Screen control You can control your phone through a series of operations on the screen.  Press: you can press the items on the screen to select, open the applications, or use the keyboard to input characters.  Slide: you can scroll up/down the page or scroll the page left/right by sliding vertically or horizontally on the screen.  Long press: you can long press some items to get the item’s available menu.  Drag: you can drag some items on the screen to realize some operations.  Switch between landscape mode and portrait mode: you can switch to the landscape mode by rotating your phone. The landscape mode is only valid under some interfaces, such as text input interface, message viewing interface, etc. Open and close the Launcher On the home screen, press the icon to open the Launcher. You can slide the Launcher left or right to view more applications. After opening the Launcher, press an icon to enter the corresponding application. Press the Back key to return to the previous screen. Press the Home key to return to the home screen. -8- Switch to a recently used application Press and hold the Home key. A window opens with icons of applications that you’ve used recently. Press an icon to open its application. Home screen Status bar Screen Indicator Notification bar Display area Icons Tap the icon to open the relevant application. Messaging Launcher icon Tap the icon to view all installed applications on the phone. Tap and hold the icon to view the home screen thumbnails. Phone -9- Add icons to the home screen Long press the empty area on the home screen to pop up the Add to Home screen menu. Select Shortcuts, Widgets, Folders, etc. You can copy icons from the Launcher to the home screen by long pressing an icon in the Launcher until the icon enlarges and the phone vibrates. Move icons on the home screen 1. Long press an icon until the icon enlarges and the phone vibrates. 2. Drag the icon to your desired position and then release. Delete icons on the home screen 1. Long press an icon until the icon enlarges and the phone vibrates. 2. Drag the icon into at the lower part of the screen to delete. Change wallpaper 1. In idle mode, press the Menu key and select Wallpaper. 2. Press Gallery / Live wallpapers / Wallpapers to enter the image library. 3. Select one image and press Set wallpaper. -10- Display the dialing keypad On the home screen, press the button to display the dialing keypad. Switch to sleep mode Sleep mode is a kind of power-saving mode, which prevents against inadvertent operations. If your phone has been in the idle mode for a while, it will automatically switch to sleep mode. You can also press the Power key to turn off the screen and enable sleep mode. Wake up your phone After the phone switches to the sleep mode, the screen …

Text truncated - open the document above for the full version.

Rev. 1/1/03 ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China Tel: +86-755-86360379 ; Fax: +86-755-86360298 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: Q78-V6700 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Schematics (file: Q78-V6700_Schem.pdf) Block Diagram (file: Q78-V6700 _BlkDia.pdf) Parts List (file: Q78-V6700_PartsLst.pdf) Operation Description (file: Q78-V6700 _OpDes.doc) Tune Up Procedure (file: Q78-V6700 _TunPro.doc) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Yours Sincerely, Royce Wang ZTE product approval manager

ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China Tel: +86-755-86360379 ; Fax: +86-755-86360298 Date: July 23, 2012 Power of Attorney To whom it may concern, Please be notified that I, Royce Wang, have designated Xuewen.Wu in Shenzhen Morlab Communications Technology Co., Ltd. and David Gong in ZTE CORPORATION as the persons being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Xuewen.Wu in Shenzhen Morlab Communications Technology Co., Ltd., and David Gong in ZTE CORPORATION on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This authorization is limited to the product of as following: FCC ID: Q78-V6700 If you have any acknowledgement and response, please send it to Shenzhen Morlab Communications Technology Co., Ltd. directly. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, Contact Person: Royce Wang Company: ZTE CORPORATION TEL: +86-755-86360379 FAX: +86-755-86360298 E-mail: [email protected]

External Photos

FCC ID: Q78-V6700 Label Label Location FCC ID Label Location

Date: July 23, 2012 Equipment Authorization Division Office of Engineering and Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: Q78-V6700 Dear Sirs: ZTE CORPORATION requests acceptance of the labeling proposal described below for cell phone bearing FCC identifier Q78-V6700. The subject cell phone are compact handheld models as shown in figure 1, authorized under 47CFR Part 22H for CDMA mobile services. Figure 1. Because the majority of the cell phone housing is composed of display, speaker, operating controls and a removable battery pack, there is extremely limited space available to attach the required label carrying the FCC identifier. Attaching the label to the battery pack is not acceptable because the battery pack is a removable item. For this reason, ZTE CORPORATION proposes placing the label carrying the FCC identifier inside the battery compartment as shown in figure 2. Figure 2. The consumer packaging for these models includes the battery pack as a separate item, NOT installed on the radio. As such, the FCC identifier will be readily visible to the user before the battery pack is installed and whenever the battery pack is removed or replaced. In this location, the label will also be protected from physical abuse and remain readable for the anticipated life of the device. The consumer packaging for these models is a "gift box" which does not allow the transceiver to be seen at time of purchase. In order to meet the requirements of 47CFR Part 2.925 (d), ZTE CORPORATION will add the FCC identifier " Q78-V6700 " to the outside of the consumer "gift box" packaging. Thank you for your attention to this matter. Yours Sincerely, Royce Wang ZTE product approval manager

Internal Photos

SZ12060127W02 Page 2 of 44 DIRECTORY 1. GENERAL INFORMATION .................................................................................................... 3 1.1. EUT Description ....................................................................................................................... 3 1.2. Test Standards and Results ........................................................................................................ 4 1.3. Facilities and Accreditations ..................................................................................................... 5 2. 47 CFR PART 15C REQUIREMENTS .................................................................................... 6 2.1. Peak Output Power.................................................................................................................... 6 2.2. Bandwidth ................................................................................................................................. 8 2.3. Conducted Spurious Emissions ............................................................................................... 13 2.4. Power spectral density (PSD) ................................................................................................. 16 2.5. Band Edge ............................................................................................................................... 21 2.6. Conducted Emission ............................................................................................................... 28 2.7. Radiated Emission................................................................................................................... 31 Change History Issue Date Reason for change 1.0 Jul 20, 2012 First edition SZ12060127W02 Page 3 of 44 1. General Information 1.1. EUT Description EUT Type ............................. : cdma2000 Digital Mobile Phone Serial No. .............................. : (n.a, marked #1 by test site) Hardware Version ................. : QB7625_02A_V1AMB_B Software Version .................. : Applicant .............................. : Manufacturer ........................ : V6700_Z46_EN_PS3CF143 ZTE Corporation ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China ZTE Corporation ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China Frequency Range .................. : 802.11b/g: 2.412GHz - 2.462GHz Channel Number................... : 802.11b/g Modulation Type .................. : DSSS (802.11b), OFDM (802.11g) Antenna Type ........................ : PIFA Antenna Antenna Gain ........................ : -3dBi Note 1: The EUT is cdma2000 Digital Mobile Phone, it contains WIFI Module operating at 2.4GHz ISM band; it supports 802.11b, 802.11g and they are all tested in this report. Note 2: The frequencies allocated is F (MHz) =2412+5*(n-1) (1<=n<=11). The lowest, middle, highest channel numbers of the EUT used and tested in this report are separately 1 (2412MHz), 6 (2437MHz) and 11 (2462MHz). Note 3: For a more detailed description, please refer to Specification or User’s Manual supplied by the applicant and/or manufacturer. SZ12060127W02 Page 4 of 44 1.2. Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 15 Subpart C (Wi-Fi, 2.4GHz ISM band radiators) for the EUT FCC ID Certification: No. Identity Document Title 1 47 CFR Part 15 (10-1-09 Edition) Radio Frequency Devices Test detailed items/section required by FCC rules and results are as below: No. Section Description Result 1 15.247(a) Number of Hopping Frequency (n.a) 2 15.247(b) Peak Output Power PASS 3 15.247(a) Bandwidth PASS 4 15.247(a) Carrier Frequency Separation (n.a) 5 15.247(a) Time of Occupancy (Dwell time) (n.a) 6 15.247(c) Conducted Spurious Emission PASS 7 15.247(c) Band Edge PASS 8 15.207 Conducted Emission PASS 9 15.209 15.247(c) Radiated Emission PASS 10 15.247(d) Power spectral density (PSD) PASS The tests of Conducted Emission and Radiated Emission were performed according to the method of measurements prescribed in ANSI C63.4 2009. These RF tests were performed according to the method of measurements prescribed in KBD558074. SZ12060127W02 Page 5 of 44 1.3. Facilities and Accreditations 1.3.1. Facilities Shenzhen Morlab Communications Technology Co., Ltd. Morlab Laboratory is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L3572. All measurement facilities used to collect the measurement data are located at FL.3, Building a, FeiYang Science Park, No.8 LongChang Road, Block 67, BaoAn District, ShenZhen, GuangDong Province, P. R. China. The test site is constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22; the FCC registration number is 741109. 1.3.2. Test Environment Conditions During the measurement, the environmental conditions were within the listed ranges: Temperature (°C): 15 - 35 Relative Humidity (%): 30 -60 Atmospheric Pressure (kPa): 86-106 SZ12060127W02 Page 6 of 44 2. 47 CFR Part 15C Requirements 2.1. Peak Output Power 2.1.1. Requirement According to FCC section 15.247(b)(3), For systems using digital modulation in the 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz bands: The maximum peak conducted output power of the intentional radiator shall not exceed1 Watt. 2.1.2. Test Description The measured output power was calculated by the reading of the Power Meter and calibration. A. Test Setup: The EUT (Equipment under the test) which is powered by the Battery is coupled to the Power Meter; the RF load attached to the EUT antenna terminal is 50Ohm; the path loss as the factor is calibrated to correct the reading, all test result in power meter. B. Equipments List: Description Manufacturer Model Serial No. Cal. Date Cal. Due EPM Series Power Meter Agilent …

Text truncated - open the document above for the full version.

Test Setup Photos 1. CE 2.RE 3. CSE