Q78-VDF545GSM Quad_band digital mobile phone

1 Product Safety Information Read the Safety Information section of this user guide on page 1 Do not use while re-fuelling Do not use hand-held while driving This device may produce a bright or flashing light For body-worn operation maintain a separation of 15 mm Do not dispose of it in a fire Small parts may cause a choking hazard Avoid contact with magnetic media This device may produce a loud sound Avoid Extreme Temperatures Keep away from pacemakers and other personal medical devices Avoid any contact with liquid, keep it dry Switch off when instructed in hospitals and medical facilities Do not attempt to disassemble Switch off when instructed in aircrafts and airports Do not rely on this device for emergency communications Switch off in explosive environments Only use approved accessories 2 RF Exposure Your phone contains a transmitter and a receiver. When it is ON, it receives and transmits RF energy. When you communicate with your phone, the system handling your call controls the power level at which your phone transmits. Specific Absorption Rate (SAR) Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines. These guidelines were developed by the independent scientific organisation ICNIRP and include safety margins designed to assure the protection of all persons, regardless of age and health. The guidelines use a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit for mobile devices is 2 W/kg and the highest SAR value for this device when tested at the ear was 0.711 W/kg*. As mobile devices offer a range of functions, they can be used in other positions, such as on the body as described in this user guide**. As SAR is measured utilising the device’s highest transmitting power, the actual SAR of this device while operating is typically below that indicated above. This is due to automatic changes to the power level of the device to ensure it only uses the minimum power required to communicate with the network. *The tests are carried out in accordance with [EN50360-2001], [EN62209-1:2006] and [IEC 62209-2:2008(106/162/CDV)]. ** Please see page 2 about body worn operation. Body worn operation Important safety information regarding radiofrequency radiation (RF) exposure To ensure compliance with RF exposure guidelines the phone must be used with a minimum of 15 mm separation from the body. 3 Failure to observe these instructions could result in your RF exposure exceeding the relevant guideline limits. Limiting exposure to radio frequency (RF) fields For individuals concerned about limiting their exposure to RF fields, the World Health Organisation (WHO) provides the following advice: Precautionary measures: Present scientific information does not indicate the need for any special precautions for the use of mobile phones. If individuals are concerned, they might choose to limit their own or their children’s RF exposure by limiting the length of calls, or using ‘hands-free’ devices to keep mobile phones away from the head and body. Further information on this subject can be obtained from the WHO home page http://www.who.int/peh-emf WHO Fact sheet 193: June 2000. Regulatory information The declaration of RoHS compliance, EC declaration of conformity and FCC compliance statement can be found on page 47 to page 51. Distraction Driving Full attention must be given to driving at all times in order to reduce the risk of an accident. Using a phone while driving (even with a hands free kit) causes distraction and can lead to an accident. You must comply with local laws and regulations restricting the use of wireless devices while driving. Operating machinery Full attention must be given to operating the machinery in order to reduce the risk of an accident. 4 Product Handling You alone are responsible for how you use your phone and any consequences of its use. You must always switch off your phone wherever the use of a phone is prohibited. Use of your phone is subject to safety measures designed to protect users and their environment. • Always treat your phone and its accessories with care and keep it in a clean and dust-free place. • Do not expose your phone or its accessories to open flames or lit tobacco products. • Do not expose your phone or its accessories to liquid, moisture or high humidity. • Do not drop, throw or try to bend your phone or its accessories. • Do not use harsh chemicals, cleaning solvents, or aerosols to clean the device or its accessories. • Do not paint your phone or its accessories. • Do not attempt to disassemble your phone or its accessories, only authorised personnel must do so. • Do not expose your phone or its accessories to extreme temperatures, minimum –[5] and maximum +[50] degrees Celsius. • Please check local regulations for disposal of electronic products. Do not carry your phone in your back pocket as it could break when you sit down. Small Children Do not leave your phone and its accessories within the reach of small children or allow them to play with it. They could hurt themselves or others, or could accidentally damage the phone. Your phone contains small parts with sharp edges that may cause an injury or which could become detached and create a choking hazard. Demagnetisation To avoid the risk of demagnetisation, do not allow electronic devices or magnetic 5 media close to your phone for a long time. Electrostatic discharge (ESD) Do not touch the SIM card’s metal connectors. Power supply Do not connect your device to the power supply or switch it on until instructed to do so in the installation instructions. Antenna Do not touch the antenna unnecessarily. Normal use position When placing or receiving a phone call, hold your phone to your ear, with the bottom towards your mouth or as you would a fixed line phone. 6 Air Bags Do not place a phone in the area over an air bag or in the air bag deployment area. Store the ph…

Text truncated - open the document above for the full version.

内部公开▲ 本文所有信息为中兴通讯股份有限公司内部信息，未经允许，不得外传 第1页，共1页 ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, 518057, P.R.China Date: Nov. 25, 2009 Power of Attorney To whom it may concern, Please be notified that I, Royce Wang have designated Zhang Min in ZTE Corporation as the persons responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Zhang Min in ZTE Corporation on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. This authorization is limited to the product of as following: FCC ID: Q78- VDF545 Any acknowledgement and response, please send it to Zhang Min directly. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, Royce Wang ZTE CORPORATION Tel: 0755-26770345 Fax: 0755-26770347 E-Mail: [email protected]

内部公开▲ 本文所有信息为中兴通讯股份有限公司内部信息，未经允许，不得外传 第1页，共1页 ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, 518057, P.R.China Date: Nov 10, 2009 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Permanent Confidentiality request for FCC ID: Q78-VDF545 To Whom It May Concern, Pursuant to sections 0.457 and 0.459 of CFR 47, the applicant requests permanent confidential treatment of the following information accompanying this application: - Block Diagram - Schematics - Operational Description - BOM list/Tune-Up-Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely yours, Royce Wang ZTE CORPORATION Tel: 0755-26770345 Fax: 0755-26770347 E-Mail: [email protected]

External Photos

Internal Photos

Report No.: RZA2009-1228FCC TESTING No. L2264 OET 65 TEST REPORT Product Name GSM Quad_band digital mobile phone Model Vodafone 545 FCC ID Q78-VDF545 Client ZTE Corporation TA Technology (Shanghai) Co., Ltd. GENERAL SUMMARY Product Name GSM Quad_band digital mobile phone Model Vodafone 545 FCC ID Q78-VDF545 Report No. RZA2009-1228 Client ZTE Corporation Manufacturer ZTE Corporation Reference Standard(s) ANSI/IEEE Std C95.1-1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. IEEE 1528–2003: Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head Due to Wireless Communications Devices: Experimental Techniques. OET Bulletin 65 supplement C, published June 2001 including DA 02-1438, published June 2002: Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits. Transition Period for the Phantom Requirements of Supplement C to OET Bulletin 65. IEC 62209-1: Human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices – Human models, instrumentation, and procedures –Part 1: Procedure to determine the Specific Absorption Rate (SAR) for hand-held devices used in close proximity to the ear. (frequency range of 300 MHz to 3 GHz). IEC 62209-2:2008(106/162/CDV): Human exposure to radio frequency fields from handheld and body-mounted wireless communication devices – Human models, instrumentation, and procedures –Part 2: Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body. ( frequency rang of 30MHz to 6GHz ) Conclusion This portable wireless equipment has been measured in all cases requested by the relevant standards. Test results in Chapter 7 of this test report are below limits specified in the relevant standards. General Judgment: Pass (Stamp) Date of issue: September 24 th , 2009 Comment The test result only responds to the measured sample. Approved by Yang Weizhong Revised by Ling Minbao Performed by Wang Lu TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 3of 127 TABLE OF CONTENT 1. General Information ..................................................................................................................... 5 1.1. Notes of the test report.........................................................................................................5 1.2. Testing laboratory .................................................................................................................5 1.3. Applicant Information ............................................................................................................6 1.4. Manufacturer Information ......................................................................................................6 1.5. Information of EUT................................................................................................................7 1.6. Test Date ..............................................................................................................................8 2. Operational Conditions during Test ..............................................................................................9 2.1. General description of test procedures .................................................................................9 2.2. GSM Test Configuration ........................................................................................................9 3. SAR Measurements System Configuration ................................................................................ 10 3.1. SAR Measurement Set-up ..................................................................................................10 3.2. DASY5 E-field Probe System ............................................................................................. 11 3.2.1. ET3DV6 Probe Specification ....................................................................................... 11 3.2.2. E-field Probe Calibration ..............................................................................................12 3.3. Other Test Equipment .........................................................................................................12 3.3.1. Device Holder for Transmitters ....................................................................................12 3.3.2. Phantom......................................................................................................................13 3.4. Scanning procedure............................................................................................................13 3.5. Data Storage and Evaluation ..............................................................................................15 3.5.1. Data Storage................................................................................................................15 3.5.2. Data Evaluation by SEMCAD ......................................................................................15 3.6. System check......................................................................................................................18 3.7. Equivalent Tissues ..............................................................................................................19 4. Laboratory Environment............................................................................................................. 20 5. Characteristics of the Test .......................................................................................................... 20 5.1. Applicable Limit Regulations ...............................................................................................20 5.2. Applicable Measurement Standards...................................................................................20 6. Conducted Output Power Measurement......…

Text truncated - open the document above for the full version.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 104of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 105of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 106of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 107of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 108of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 109of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 110of 127 ANNEX F: D1900V2 Dipole Calibration Certificate TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 111of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 112of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 113of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 114of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 115of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 116of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 117of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 118of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 119of 127 ANNEX G: DAE4 Calibration Certificate TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 120of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 121of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 122of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 123of 127 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 124of 127 ANNEX H: The EUT Appearances and Test Configuration Picture 6: Constituents of EUT Picture 7: Left Hand Touch Cheek Position TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 125of 127 Picture 8: Left Hand Tilt 15 Degree Position Picture 9: Right Hand Touch Cheek Position TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 126of 127 Picture 10: Right Hand Tilt 15 Degree Position Picture 11: Body, The EUT display towards ground, the distance from handset to the bottom of the Phantom is 15mm TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA2009-1228FCC Page 127of 127 Picture 12: Body, The EUT display towards phantom, the distance from handset to the bottom of the Phantom is 15mm Picture 13: Body with earphone, The EUT display towards ground, the distance from handset to the bottom of the Phantom is 15mm)

No.2009TAR169 Page1 of 73 ©Copyright. All rights reserved by TMC Beijing. TEST REPORT No. 2009TAR169 for ZTE CORPORATION GSM Quad_band digital mobile phone Model Name: Vodafone 545 FCC ID : Q78-VDF545 with Hardware Version: g7rC Software Version: VDF-P160A6B02-FrEsPtHiArZh-DE05 Issued Date: Nov 25th, 2009 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of TMC Beijing. Test Laboratory: DAR accreditation (DIN EN ISO/IEC 17025): No. DAT-P-114/01-01 FCC 2.948 Listed: No.733176 IC O.A.T.S listed: No.6629A-1 TMC Beijing, Telecommunication Metrology Center of Ministry of Industry and Information Technology No. 52, Huayuan Bei Road, Haidian District, Beijing, P. R. China 100083. Tel:+86(0)10-62303288-2105, Fax:+86(0)10-62304793 Email:[email protected]. www.emcite.com No.2009TAR169 Page2 of 73 ©Copyright. All rights reserved by TMC Beijing. CONTENTS 1. TEST LABORATORY .............................................................................................................. 3 1.1. TESTING LOCATION .......................................................................................................... 3 1.2. TESTING ENVIRONMENT .................................................................................................. 3 1.3. PROJECT DATA .................................................................................................................. 3 1.4. SIGNATURE ........................................................................................................................ 3 2. CLIENT INFORMATION .......................................................................................................... 4 2.1. APPLICANT INFORMATION............................................................................................... 4 2.2. MANUFACTURER INFORMATION ..................................................................................... 4 3. EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ............................ 5 3.1. ABOUT EUT ........................................................................................................................ 5 3.2. INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST ................................... 5 3.3. INTERNAL IDENTIFICATION OF AE USED DURING THE TEST ...................................... 5 3.4. GENERAL DESCRIPTION .................................................................................................. 6 4. REFERENCE DOCUMENTS .................................................................................................. 6 4.1. REFERENCE DOCUMENTS FOR TESTING ...................................................................... 6 5. LABORATORY ENVIRONMENT ............................................................................................ 7 6. SUMMARY OF TEST RESULTS ............................................................................................. 8 7. TEST EQUIPMENTS UTILIZED .............................................................................................. 8 ANNEX A: MEASUREMENT RESULTS ........................................................................................ 9 A.1 OUTPUT POWER ............................................................................................................... 9 A.2 EMISSION LIMT ............................................................................................................... 14 A.3 CONDUCTED EMISSION ................................................................................................. 27 A.4 FREQUENCY STABILITY ................................................................................................. 31 A.5 OCCUPIED BANDWIDTH ................................................................................................... 33 A.6 EMISSION BANDWIDTH .................................................................................................... 45 A.7 BAND EDGE COMPLIANCE ............................................................................................... 57 A.8 CONDUCTED SPURIOUS EMISSION ............................................................................... 63 No.2009TAR169 Page3 of 73 ©Copyright. All rights reserved by TMC Beijing. 1. Test Laboratory 1.1. Testing Location Company Name: TMC Beijing, Telecommunication Metrology Center of MIIT Address: No 52, Huayuan beilu, Haidian District, Beijing,P.R.China Postal Code: 100083 Telephone: 00861062303288 Fax: 00861062304793 1.2. Testing Environment Normal Temperature: 15-35°C Relative Humidity: 20-75% 1.3. Project data Testing Start Date: Oct 16 th , 2009 Testing End Date: Nov 24 th , 2009 1.4. Signature Zi Xiaogang (Prepared this test report) Sun Xiangqian (Reviewed this test report) Lu Bingsong Deputy Director of the laboratory (Approved this test report) No.2009TAR169 Page4 of 73 ©Copyright. All rights reserved by TMC Beijing. 2. Client Information 2.1. Applicant Information Company Name: ZTE CORPORATION Address /Post: ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, 518057, P.R.China City: Shenzhen Postal Code: 518057 Country: China Telephone: 0086 21 68895196 Fax: 0086 21 61460600 2.2. Manufacturer Information Company Name: ZTE CORPORATION Address /Post: ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, 518057, P.R.China City: Shenzhen Postal Code: 518057 Country: China Telephone: 0086 21 68895196 Fax: 0086 21 61460600 No.2009TAR169 Page5 of 73 ©Copyright. All rights reserved by TMC Beijing. 3. Equipment Under Test (EUT) and Ancillary Equipment (AE) 3.1. About EUT Description GSM Quad_band digital mobile phone Model Name Vodafone 545 FCC ID Q78-VDF545 Frequency GSM 850MHz; PCS 1900MHz Antenna Internal Power supply Battery or Charger (AC Adaptor) Output power 30.72 dBm maximum EIRP measured for PCS190…

Text truncated - open the document above for the full version.

VDF 545 FCC test setup photo 1． Radiated Spurious Emission 2． Part15B Radiated Emission 3． Part15C Radiated Emission 4． Part15B Conducted Emission 5． Part15C Conducted Emission