Q9Z-PC5NR3-J1Wireless Tablet

Hitachi VisionPlate User Manual i User Manual for Embedded Linux and Microsoft Windows XP Embedded Operating Systems Chapter ii Copyright © 2003 Hitachi Data Systems. All rights reserved. This publication contains information that is protected by copyright. No part of it may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without permission from Hitachi Data Systems. Trademarks Crusoe is a trademark of Transmeta Corporation. Microsoft, MS-DOS, and Windows are registered trademarks of Microsoft Corporation. All trademarks, trade names, and service marks used herein are the rightful property of their respective owners. Hitachi VisionPlate User Manual iii Chapter iv Table of Contents 1Safety Information...........................................................................................................................................1 1.1Introduction.................................................................................................................................................. 1 1.2Tips for Safe Operation............................................................................................................................. 1 1.3Vision Risk Factors....................................................................................................................................... 2 1.4Hand and Wrist Motor Risk Factors..................................................................................................... 2 1.5Body Support Risk Factors....................................................................................................................... 3 1.6Product Safety Guidelines........................................................................................................................ 3 1.7Main Battery Pack Guidelines................................................................................................................ 4 1.8Power Cord Guidelines.............................................................................................................................. 4 1.9AC Adapter Guidelines.............................................................................................................................. 5 1.10Restrictions for AC Adapters................................................................................................................... 6 1.11Liquid Crystal Display (LCD) Guidelines.............................................................................................. 6 1.12Proper Treatment of Your Hitachi Product....................................................................................... 7 1.13Safety and Regulatory Compliance...................................................................................................... 8 1.14General Safety Guidelines......................................................................................................................10 1.15Battery Safety Guidelines.......................................................................................................................11 1.16Operating Safety Guidelines.................................................................................................................11 2Getting Started................................................................................................................................................ 12 2.1Identifying Components.........................................................................................................................12 2.2Setting up Your VisionPlate..................................................................................................................16 2.3Mobile Use...................................................................................................................................................20 2.4Powering the VisionPlate On and Off..............................................................................................22 2.5Using the Stylus.........................................................................................................................................24 2.6Battery Use and Maintenance..............................................................................................................26 3Using Your VisionPlate with Embedded Linux............................................................................. 28 3.1Touchscreen Calibration.........................................................................................................................28 3.2Adjusting the Brightness of the LCD.................................................................................................29 3.3Adjusting the Volume.............................................................................................................................30 3.4Prolonging Battery Life and Instant on/off Functionality.........................................................31 3.5Low Battery Notification Settings......................................................................................................32 3.6Installing and Removing PC Cards......................................................................................................32 3.7Installing and Removing Compact Flash (CF) Cards....................................................................34 3.8Wireless LAN Configuration..................................................................................................................36 3.9Screen Rotation..........................................................................................................................................37 Hitachi VisionPlate User Manual v 3.10Programmable Button............................................................................................................................38 4Using Your VisionPlate with Windows XP embedded.............................…

Text truncated - open the document above for the full version.

1 Mike Kuo From: Claire Hoque Sent: April302004Friday 4:20 PM To: Mike Kuo Cc: Sunny Shih; Michael Heckrotte; Julia Luke; Kathy Yao Subject: RE: Hitachi Keiyo Engineering and Systems, Ltd, FCC ID:Q9Z-PC5NR3-J1, AN04T3851 Hi Mike, Here are the answer. Question #1: There are two antenna specification file provided but based upon the internal photos, only two identical antennas are used. Please explain. <Hitachi>One is the behavior of the primary antenna and the other one is the behavior of the secondary antenna. Question #2: Please provide additional internal photo of the solder side of main board for tablet. <Claire>pls see revised internal photos. Internal Photos(revised).pdf Question #3: In page 2 of SAR test report, 802.11 bg is mentioned but this device is 802.11b radio. Please make necessary correction. <Sunny>The 802.11bg was a typographical error. It is corrected in the attached updated report. 04U2611 SAR Report(Updated 4-3... Question #4: During body worn SAR tests, based upon setup photos, there are data cable connected to the device. Is the device tested with battery power or from AC/DC adaptor ? What is the purpose of data cable used during SAR tests ? <Sunny>There are two cables, first one is USB floppy to run the test program, and the other one is USB Mouse. The EUT power came from battery, not AC/DC adaptor. Thanks, Claire

PROPOSED FCC ID LABEL AND LOCATION HITACHI KEIYO ENGINEERING AND SYSTEMS, LTD This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: Q9Z-PC5NR3-J1 FCC ID LABEL LOCATION

Small Ceramic Chip Antenna Small Ceramic Chip Antenna for for Bluetooth Bluetooth Hitachi Metals, Ltd. Tottori Works R&D Department http://www.hitachi-metals.co.jp Page. 1/4 SMA-F24016A1TL 3.Specifications Hitachi Metals, Ltd. Tottori Works Page. 2/4 1. Feature Omni-directional Wide Bandwidth High Gain Small & SMD Easy to use (adjustment free) 2. Dimensions 10mm x 3mm x 2mm Frequency Range2400 -2484MHz Band Width160MHz (Typical Value) VSWR2.0 Max. Gain-4dBi Input Impedance50 Ohm 4.Foot Pattern Unit:mm 2 1 10 2 3 22 1 3 . 5 4 . 5 (1) Signal (2) NC (Mount Point) (3) GND 0.5 1.5 0.5 (2) (1) (3) 5. Application Note 5mm Back Side Circuit Board (Evaluation) Ceramic Antenna Need Blank Space 5mm Need 1mm Space from Grand Plane 1mm 7. Measurement Data 7-1. VSWR vs. Frequency Hitachi Metals, Ltd. Tottori Works Page. 3/4 24502250 2650 Frequency (MHz) VSWR 1 2 3 Z X Y 270 180 90 Hitachi Metals, Ltd. Tottori Works Page. 4/4 7-2. Radiation Pattern and Gain HorizontalVerticalH/V Ave.HorizontalVerticalH/V Ave.HorizontalVerticalH/V Ave. Ave.[dBi]-3.1-4.7-3.8Ave.[dBi]-1.7-12.1-4.3Ave.[dBi]-6.2-2.5-4.0 Max.[dBi]0.9-1.7-0.2Max.[dBi]1.6-8.3-1.0Max.[dBi]-2.4-1.1-1.7 -35 -25 -15 -5 5 0 30 60 90 120 150 180 210 240 270 300 330 -35 -25 -15 -5 5 0 30 60 90 120 150 180 210 240 270 300 330 -35 -25 -15 -5 5 0 30 60 90 120 150 180 210 240 270 300 330 Horizontal Vertical Horizontal Vertical Horizontal Vertical X-Y Plane Y-Z PlaneZ-X Plane 0

HorizontalVertical HorizontalVertical HorizontalVertical

in accordance with the requirements of FCC Report and Order: ET Docket 93-62, and OET Bulletin 65 Supplement C for VisionPlat TM Wireless Tablet PC Model: PC5NR3-XXXXXXXXX FCC ID: Q9Z-PC5NR3-J1 April 9, 2004 REPORT NO: 04U2611-2 Prepared for Hitachi Keiyo Engineering and Systems, Ltd 7chome-1-1 Higashinarashino Narashino-shi, Chiba-ken, 275-0001 Japan Prepared by Compliance Certification Services 561F Monterey Road Morgan Hill, CA 95037 USA TEL: (408) 463-0885 REPORT NO: 04U2611-2 DATE: April 9, 2004 FCC ID: Q9Z-PC5NR3-J1 COMPLIANCE CERTIFICATION SERVICES Page: 2 of 25 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Dates of Tests: April 9, 2004 APPLICANT: Hitachi Keiyo Engineering and Systems, Ltd 7chome-1-1 Higashinarashino Narashino-shi, Chiba-ken, 275-0001, Japan MODEL: PC5NR3-XXXXXXXXX FCC ID: Q9Z-PC5NR3-J1 DEVICE CATEGORY: PORTABLE DEVICES EXPOSURE CATEGORY: GENERAL POPULATION/UNCONTROLLED EXPOSURE Test Sample is a: Production unit Modulation type: Direct Sequence Spread Spectrum (DSSS) for 802.11b Tx Frequency: 2412 to 2462 MHz Max. O/P Power: (Conducted/Average) 19.4 dBm Max. SAR (1g): 0.340 mW/g Equipment Class: Digital Transmission System (DTS) FCC Rule Part(s): 15C This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in FCC OET 65 Supplement C (released on 6/29/2001 see Test Report). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Hsin-Fu Shih (Sunny Shih) Senior Engineer REPORT NO: 04U2611-2 DATE: April 9, 2004 FCC ID: Q9Z-PC5NR3-J1 COMPLIANCE CERTIFICATION SERVICES Page: 3 of 25 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. TABLE OF CONTENTS 1. EQUIPMENT UNDER TEST (EUT) DESCRIPTION........................................................... 4 2. REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC............................... 4 3. DOSIMETRIC ASSESSMENT SYSTEM.......................................................................... 4 3.1. MEASUREMENT SYSTEM DIAGRAM......................................................................................................5 3.2. SYSTEM COMPONENTS.......................................................................................................................6 4. EVALUATION PROCEDURES..................................................................................... 8 5. MEASUREMENT UNCERTAINTY............................................................................... 12 6. EXPOSURE LIMIT................................................................................................. 13 7. PROCEDURES USED TO ESTABLISH TEST SIGNALS................................................... 13 8. MEASUREMENT RESULTS...................................................................................... 14 8.1. SIMULATING LIQUIDS PARAMETER CHECK..........................................................................................14 8.2. SYSTEM PERFORMANCE CHECK........................................................................................................17 8.3. SAR MEASUREMENTS RESULTS.......................................................................................................18 9. PHOTOS............................................................................................................. 20 10. EQUIPMENT LIST & CALIBRATION STATUS............................................................... 23 11. REFERENCES...................................................................................................... 24 12. ATTACHMENTS.................................................................................................... 25 REPORT NO: 04U2611-2 DATE: April 9, 2004 FCC ID: Q9Z-PC5NR3-J1 COMPLIANCE CERTIFICATION SERVICES Page: 4 of 25 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 1. EQUIPMENT UNDER TEST (EUT) DESCRIPTION The EUT is an 802.11b transceiver. It is installed in a Hitachi Tablet PC host computer; model AIR- MPI352, FCC ID LDK102042. The WLAN radio utilizes two identical internal antennas for diversity. • Antennas (A0, A1) - The WLAN radio utilizes two internal antennas for diversity. Manufactured by Hitachi, P/N: SMA-F24016A1TL, gain: -4dBi • Battery Pack - Hitachi, Li-ion type, model PC-AB5900, rating 11.1V, 1.17Ah. Alternate - Same as above, except model PC-AB5910, rating 11.1V, 3.4Ah. 2. REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC The US Federal Communications Commission has released the report and order “Guidelines for Evaluating the Environmental Effects of RF Radiation", ET Docket No. 93-62 in August 1996 [1]. The order requires routine SAR evaluation prior to equipment authorization of portable transmitter devices, including portable telephones. For consumer products, the applicable limit is 1.6 mW/g for an uncontrolled environment and 8.0 mW/g for an occupational/controlled environment as recommended by the ANSI/IEEE standard C95.1-1992 [6]. According to…

Text truncated - open the document above for the full version.

Date/Time: 04/09/04 10:25:42 Test Laboratory: The name of your organization D2450V2SN706_Probe 3021_040904 DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 - SN:706 Ambient temperature = 23.0 deg. C; Liquid temperature = 22.0 deg. C Communication System: CW - 2450 MHz; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2450 MHz; σ = 1.89 mho/m; ε r = 38.7; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: z Probe: ES3DV2 - SN3021; ConvF(4.5, 4.5, 4.5); Calibrated: 7/29/2003 z Sensor-Surface: 4mm (Mechanical Surface Detection) z Electronics: DAE3 Sn500; Calibrated: 12/23/2003 z Phantom: SAM 1; Type: SAM 1; Serial: 1185 z Measurement SW: DASY4, V4.2 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 112 d=10mm, Pin=250mW/Area Scan (7x7x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 90.7 V/m; Power Drift = 0.0 dB Maximum value of SAR (measured) = 15.1 mW/g d=10mm, Pin=250mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 90.7 V/m; Power Drift = 0.0 dB Maximum value of SAR (measured) = 14.9 mW/g Peak SAR (extrapolated) = 29.5 W/kg SAR(1 g) = 13.6 mW/g; SAR(10 g) = 6.17 mW/g 0 dB = 14.9mW/g Date/Time: 04/02/04 14:11:20 Test Laboratory: The name of your organization D2450V2SN706_Probe 3021_040204 DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 - SN:706 DASY4 Configuration: z Probe: ES3DV2 - SN3021; ConvF(4.5, 4.5, 4.5); Calibrated: 7/29/2003 z Sensor-Surface: 0mm (Fix Surface) z Electronics: DAE3 Sn500; Calibrated: 12/23/2003 z Phantom: SAM 1; Type: SAM 1; Serial: 1185 z Measurement SW: DASY4, V4.2 Build 37; Postprocessing SW: SEMCAD, V1.8 Build 109 d=10mm, Pin=250mW/Z Scan (1x1x51): Measurement grid: dx=20mm, dy=20mm, dz=2mm Reference Value = 93.3 V/m; Power Drift = -0.003 dB Maximum value of SAR (measured) = 16 mW/g

Date/Time: 04/09/04 10:53:40 Test Laboratory: The name of your organization 1_EUT Setup Configuration 1_A0 Antenna DUT: Hitachi Keiyo Engineering and Systems, Ltd; Type: PC5NR3-XXXXXXXXX; Serial: 90043 Ambient temperature = 23.0 deg. C; Liquid temperature = 22.0 deg. C Communication System: 802.11b; Frequency: 2412 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 2412 MHz; σ = 1.99 mho/m; ε r = 51.8; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: z Probe: ES3DV2 - SN3021; ConvF(4.1, 4.1, 4.1); Calibrated: 7/29/2003 z Sensor-Surface: 4mm (Mechanical Surface Detection) z Electronics: DAE3 Sn500; Calibrated: 12/23/2003 z Phantom: SAM 2; Type: SAM 2; Serial: 1050 z Measurement SW: DASY4, V4.2 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 112 Low Ch./Area Scan (8x9x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 2.28 V/m; Power Drift = 0.17 dB Maximum value of SAR (measured) = 0.289 mW/g Low Ch./Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 2.28 V/m; Power Drift = 0.17 dB Maximum value of SAR (measured) = 0.330 mW/g Peak SAR (extrapolated) = 0.554 W/kg SAR(1 g) = 0.299 mW/g; SAR(10 g) = 0.156 mW/g Date/Time: 04/09/04 10:53:40 Test Laboratory: The name of your organization 1_EUT Setup Configuration 1_A0 Antenna DUT: Hitachi Keiyo Engineering and Systems, Ltd; Type: PC5NR3-XXXXXXXXX; Serial: 90043 Ambient temperature = 23.0 deg. C; Liquid temperature = 22.0 deg. C Communication System: 802.11b; Frequency: 2437 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 2437 MHz; σ = 2.01 mho/m; ε r = 51.7; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: z Probe: ES3DV2 - SN3021; ConvF(4.1, 4.1, 4.1); Calibrated: 7/29/2003 z Sensor-Surface: 4mm (Mechanical Surface Detection) z Electronics: DAE3 Sn500; Calibrated: 12/23/2003 z Phantom: SAM 2; Type: SAM 2; Serial: 1050 z Measurement SW: DASY4, V4.2 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 112 Middle Ch./Area Scan (8x9x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 2.57 V/m; Power Drift = 0.13 dB Maximum value of SAR (measured) = 0.316 mW/g Middle Ch./Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 2.57 V/m; Power Drift = 0.13 dB Maximum value of SAR (measured) = 0.376 mW/g Peak SAR (extrapolated) = 0.639 W/kg SAR(1 g) = 0.340 mW/g; SAR(10 g) = 0.177 mW/g Date/Time: 04/09/04 10:53:40 Test Laboratory: The name of your organization 1_EUT Setup Configuration 1_A0 Antenna DUT: Hitachi Keiyo Engineering and Systems, Ltd; Type: PC5NR3-XXXXXXXXX; Serial: 90043 DASY4 Configuration: z Probe: ES3DV2 - SN3021; ConvF(4.1, 4.1, 4.1); Calibrated: 7/29/2003 z Sensor-Surface: 0mm (Fix Surface) z Electronics: DAE3 Sn500; Calibrated: 12/23/2003 z Phantom: SAM 2; Type: SAM 2; Serial: 1050 z Measurement SW: DASY4, V4.2 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 112 Middle Ch./Z Scan (1x1x51): Measurement grid: dx=20mm, dy=20mm, dz=2mm Reference Value = 2.57 V/m; Power Drift = 0.1 dB Maximum value of SAR (measured) = 0.391 mW/g Date/Time: 04/09/04 10:53:40 Test Laboratory: The name of your organization 1_EUT Setup Configuration 1_A0 Antenna DUT: Hitachi Keiyo Engineering and Systems, Ltd; Type: PC5NR3-XXXXXXXXX; Serial: 90043 Ambient temperature = 23.0 deg. C; Liquid temperature = 22.0 deg. C Communication System: 802.11b; Frequency: 2462 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 2462 MHz; σ = 2.05 mho/m; ε r = 51.6; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: z Probe: ES3DV2 - SN3021; ConvF(4.1, 4.1, 4.1); Calibrated: 7/29/2003 z Sensor-Surface: 4mm (Mechanical Surface Detection) z Electronics: DAE3 Sn500; Calibrated: 12/23/2003 z Phantom: SAM 2; Type: SAM 2; Serial: 1050 z Measurement SW: DASY4, V4.2 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 112 High Ch./Area Scan (8x9x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 2.49 V/m; Power Drift = 0.1 dB Maximum value of SAR (measured) = 0.324 mW/g High Ch./Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 2.49 V/m; Power Drift = 0.1 dB Maximum value of SAR (measured) = 0.323 mW/g Peak SAR (extrapolated) = 0.575 W/kg SAR(1 g) = 0.294 mW/g; SAR(10 g) = 0.152 mW/g Date/Time: 04/09/04 13:56:25 Test Laboratory: The name of your organization 2_EUT Setup Configuration 1_A1 antenna DUT: Hitachi Keiyo Engineering and Systems, Ltd; Type: PC5NR3-XXXXXXXXX; Serial: 90043 Ambient temperature = 23.0 deg. C; Liquid temperature = 22.0 deg. C Communication System: 802.11b; Frequency: 2412 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 2412 MHz; σ = 1.99 mho/m; ε r = 51.8; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: z Probe: ES3DV2 - SN3021; ConvF(4.1, 4.1, 4.1); Calibrated: 7/29/2003 z Sensor-Surface: 4mm (Mechanical Surface Detection) z Electronics: DAE3 Sn500; Calibrated: 12/23/2003 z Phantom: SAM 2; Type: SAM 2; Serial: 1050 z Measurement SW: DASY4, V4.2 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 112 Low Ch./Area Scan (8x9x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 3.54 V/m; Power Drift = 0.12 dB Maximum value of SAR (measured) = 0.236 mW/g Low Ch./Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 3.54 V/m; Power Drift = 0.12 dB Maximum value of SAR (measured) = 0.237 mW/g Peak SAR (extrapolated) = 0.393 W/kg SAR(1 g) = 0.218 mW/g; SAR(10 g) = 0.120 mW/g Date/Time: 04/09/04 13:56:25 Test Laboratory: The name of your organization 2_EUT Setup Configuration 1_A1 antenna DUT: Hitachi Keiyo Engineering and Systems, Ltd; Type: PC5NR3-XXXXXXXXX; Serial: 90043 Ambient temperature = 23.0 deg. C; Liquid temperature = 22.0 deg. C Communication System: 802.11b; Frequen…

Text truncated - open the document above for the full version.

FCC CFR47 PART 15 SUBPART C CERTIFICATION TEST REPORT FOR WIRELESS TABLET MODEL NUMBER: PC5NR3-XXXXXXXXX FCC ID: Q9Z-PC5NR3-J1 REPORT NUMBER: 04U2611-1 ISSUE DATE: APRIL 15, 2004 Prepared for HITACHI KEIYO ENGINEERING AND SYSTEMS, LTD 7CHOME-1-1 HIGASHINARASHINO NARASHINO-SHI, CHIBA-KEN JAPAN, 275-0001 Prepared by COMPLIANCE CERTIFICATION SERVICES 561F MONTEREY ROAD, MORGAN HILL, CA 95037, USA TEL: (408) 463-0885 FAX: (408) 463-0888 REPORT NO: 04U2611 DATE: APRIL 15, 2004 EUT: WIRELESS TABLET FCC ID: Q9Z-PC5NR3-J1 Page 2 of 69 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION.................................................................................................. 3 2. EUT DESCRIPTION.......................................................................................................................... 4 3. TEST METHODOLOGY .................................................................................................................. 5 4. FACILITIES AND ACCREDITATION .......................................................................................... 5 5. CALIBRATION AND UNCERTAINTY.......................................................................................... 6 5.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 6 5.2. MEASUREMENT UNCERTAINTY ............................................................................................... 6 5.3. TEST AND MEASUREMENT EQUIPMENT................................................................................ 7 6. SETUP OF EQUIPMENT UNDER TEST ....................................................................................... 8 7. APPLICABLE LIMITS AND TEST RESULTS ........................................................................... 12 7.1. 6 dB BANDWIDTH ..................................................................................................................... 12 7.2. 99% BANDWIDTH ..................................................................................................................... 16 7.3. PEAK OUTPUT POWER............................................................................................................ 20 7.4. AVERAGE POWER..................................................................................................................... 24 7.5. PEAK POWER SPECTRAL DENSITY ....................................................................................... 25 7.6. CONDUCTED SPURIOUS EMISSIONS.................................................................................... 29 7.7. RADIATED EMISSIONS.............................................................................................................36 7.7.1. TRANSMITTER RADIATED SPURIOUS EMISSIONS ................................................. 36 7.7.2. TRANSMITTER RADIATED EMISSIONS ABOVE 1 GHZ .......................................... 39 7.7.3. TRANSMITTER RADIATED EMISSIONS ABOVE 1 GHZ (PORTABLE CONFIGURATION) .......................................................................................................................... 48 7.7.4. WORST-CASE RADIATED EMISSIONS BELOW 1 GHz ............................................. 53 7.8. POWERLINE CONDUCTED EMISSIONS ................................................................................ 57 8. SETUP PHOTOS .............................................................................................................................. 61 REPORT NO: 04U2611 DATE: APRIL 15, 2004 EUT: WIRELESS TABLET FCC ID: Q9Z-PC5NR3-J1 Page 3 of 69 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 1. TEST RESULT CERTIFICATION COMPANY NAME: HITACHI KEIYO ENGINEERING AND SYSTEMS, LTD 7CHOME-1-1 HIGASHINARASHINO NARASHINO-SHI, CHIBA-KEN JAPAN, 275-0001 EUT DESCRIPTION: WIRELESS TABLET MODEL: PC5NR3-XXXXXXXXX DATE TESTED: APRIL 6 – 14, 2004 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C NO NON-COMPLIANCE NOTED Compliance Certification Services, Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: This document reports conditions under which testing was conducted and results of tests performed. This document may not be altered or revised in any way unless done so by Compliance Certification Services and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by Compliance Certification Services will constitute fraud and shall nullify the document. Approved & Released For CCS By: Tested By: MIKE HECKROTTE VIEN TRAN ENGINEERING MANAGER EMC TECHNICIAN COMPLIANCE CERTIFICATION SERVICES COMPLIANCE CERTIFICATION SERVICES REPORT NO: 04U2611 DATE: APRIL 15, 2004 EUT: WIRELESS TABLET FCC ID: Q9Z-PC5NR3-J1 Page 4 of 69 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be no…

Text truncated - open the document above for the full version.

REPORT NO: 04U2611 DATE: APRIL 12, 2004 EUT: WIRELESS TABLET FCC ID: Q9Z-PC5NR3-J1 Page 62 of 70 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 8. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP ANTENNA PORT CONDUCTED PHOTO REPORT NO: 04U2611 DATE: APRIL 12, 2004 EUT: WIRELESS TABLET FCC ID: Q9Z-PC5NR3-J1 Page 63 of 70 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without…

Text truncated - open the document above for the full version.